• Korean Journal of Materials Research
• /
• v.14 no.3
• /
• pp.181-185
• /
• 2004

The mechanical properties of a bulk amorphous alloy ($Zr_{41.2}$ $Ti_{13.8}$ /$Cu_{10}$ $Ni_{10}$ $Be_{22.5}$ /at.%) before and after an annealing treatment were investigated. For the bulk amorphous alloy, the compressive strength was about 2.0 GPa, irrespective of the strain rates in the range of $10^{-4}$ to $10^3$$ sec^{-1}$ . Fine-sized nanocrystalline particles (10～100 nm) were precipitated homogeneously in the bulk amorphous matrix after the annealing treatments. Compared to the bulk amorphous materials, these composite materials, composed of the nanocrystalline phases and a bulk amorphous matrix had much different mechanical properties. The strength and strain of coposite materials measured by a compressive test showed a peak-maximum values at 7 vol.% of the nanocrystalline phases. The values in higher volume fraction of the crystalline phases in the amorphous matrix were decreased, as measured by both quasi-static and high strain rate. The decrease in fracture strength is due to presence of the dispersed large-crystalline phases in the amorphous matrix.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.3
• /
• pp.248-252
• /
• 2005

The effects of electric field strength and mechanical compressive stress on the displacement of multilayered ceramic actuator, stacked alternatively 0.2 (PbM $n_{1}$3/N $b_{2}$3/ $O_3$)-0.8(PbZ $r_{0.475}$ $Ti_{0.525}$ $O_3$) ceramic thin films and 70Ag-30Pd electrodes were investigated. Because the actuators were designed to stack ceramic layer and electrode layer alternatively, the ceramic-electrode interfaces may act as a resistance to motion of domain wall. so the polarization and strain were affected by the amount of 180$^{\circ}$domain, electric field strength and mechanical compressive stress. Consequently, the change of polarization, displacement with respect to field strength, and mechanical compressive stress were likely to be caused by readiness of the domain wall movement around the ceramic-electrode interfaces.ces.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.341-344
• /
• 1999

The effects of post annealing treatments of ferroelectrlclty in PZT(P $b_{1.05}$(Z $r_{0.52}$, $Ti_{0.48}$) $O_3$ thin film deposited on Pt/ $SiO_2$/Si substrate by RF-Magnetron sputtering methode was Investigated. Analyses by RTA(Rapid Thermal Annealing) treatments reveled that the crystallization process strongly depend on the healing temperature. The Perovskite structure with strong PZT (101) plan was obtained by RTA treatments at 75$0^{\circ}C$ With increasing RTA temperature of PZI thin films, the coercive field and remanent Polarization decreased, while saturation polarization( $P_{r}$) was decreased. P-E curves of Pt/PZT/Pt capacitor structures demonstrate typical hysteresiss loops. The measure values of $P_{r}$,. $E_{c}$ and dielectric constants by post annealed at 75$0^{\circ}C$ were 38 $\mu$C/$\textrm{cm}^2$ 35KV/cm and 974, respectively. Switching polarization versus fatigue characteristic showed 12% degradation up to 10$^{7}$ cycles.s.s.s.s.s.s.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.2
• /
• pp.110-115
• /
• 2019

$Pb(Sb_{0.5}Nb_{0.5})_x(Zr_{0.51}Ti_{0.49})_{1-x}O_3$ (abbreviation: PSN-PZT) ceramics were synthesized, using conventional bulk ceramic processing technology, with various PSN doping contents. The maximum density of PSN-PZT was 97% of the theoretical density in the samples sintered at $1,250^{\circ}C$. The maximum values of the piezoelectric properties achieved using the conventional processes were: $k_p$ of 0.625, $d_{33}$ of 531 pC/N, and $g_{33}$ of $33mV{\cdot}m/N$. Finally, we fabricated a piezo-speaker with the optimized PSN-PZT ceramics. The SPL of the speaker was measured at a distance of 1 m, with a driving voltage of $40V_{rms}$ in the frequency range of ~300 Hz to 9 kHz. The measured $SPL_{max}$ was at a very high level (95 dB), which was superior in quality in comparison with those of other commercial products.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.05a
• /
• pp.155-160
• /
• 2002

Metal matrix composites had generated a lot of interest in recent times because of significant in specific properties. It was also highlighted as the materials of frontier industry because strength, heat-resistant, corrosion-resistant, wear-resistant were superiored. In this study the strength properties of $Al_{18}B_4O_{33}/AC4CH$ were represented mixing the binder of $Al_2O_3$ and $TiO_2$. It was also fabricated by squeeze casting. $Al_{18}B_4O_{33}/AC4CH$ was fabricated at the melt temperature of $760^{\circ}C$ the perform temperature of $700^{\circ}C$ and mold temperature of $200^{\circ}C$ under the pressure of 83.4MPa and observed SEM. Fatigue crack growth rate tests on compact tension specimen(half-size) of thickness 12.5mm were conducted by using sinusoidal waveform. Compact tension specimens(half-size) were used and fatigue crack growth rate da/dN and stress intensity factor range ${\Delta}K$ were analyzed concerning to the R value of 0.1 and 0.05. In order to find out the value of ${\Delta}K$, load amplitude constant method was applied by the standard fatigue testing method describes in ASTM E647-95a. As the results of this study, Fatigue crack growth rate increased with in creasing the load ratio, Consequently, At equivalent stress intensity factors, the fatigue crack growth rates in MMC were faster than those of AC4CH alloy. then the fatigue life and the fatigue crack growth rate was investigated using scanning election microscopy(SEM)

• Progress in Superconductivity
• /
• v.10 no.2
• /
• pp.139-143
• /
• 2009

We have fabricated a low-noise 61-channel axial-type first-order gradiometer system for measuring fetal magnetocardiography(MCG) signals. Superconducting quantum interference device(SQUID) sensor was based on double relaxation oscillation SQUID(DROS) for detecting biomagnetic signal, such as MCG, magnetoencphalogram(MEG) and fetal-MCG. The SQUID sensor detected axial component of fetal MCG signal. The pickup coil of SQUID sensor was wound with 120 ${\mu}m$ NbTi wire on bobbin(20 mm diameter) and was a first-order gradiometer to reject the environment noise. The sensors have low white noise of 3 $fT/Hz^{1/2}$ at 100 Hz on average. The fetal MCG was measured from $24{\sim}36$ weeks fetus in a magnetically shielded room(MSR) with shielding factor of 35 dB at 0.1 Hz and 80 dB at 100 Hz(comparatively mild shielding). The MCG signal contained maternal and fetal MCG. Fetal MCG could be distinguished relatively easily from maternal MCG by using independent component analysis(ICA) filter. In addition, we could observe T peak as well as QRS wave, respectively. It will be useful in detecting fetal cardiac diseases.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.2
• /
• pp.1003-1007
• /
• 2013

Objective: This work aimed to investigate the correlations of tumor-associated macrophages (TAMs) and their subtypes M1 and M2 with liver metastasis of colorectal cancer, and provide useful references for seeking predictors of liver metastasis and studying mechanisms. Methods: 120 patients with colorectal cancer from 2000 to 2009 were divided into low, middle and high liver metastasis groups (group A, B and C, respectively). S-P immunohistochemical staining and microscopic observation were conducted to compare expression in CD68-positive cells (TAMs), CD80-positive cells (M1) and CD163-positive cells (M2) in three groups. Correlations of TAMs, M1, M2, and M2/M1 ratio with clinical and pathological parameters were analyzed. Results: With increase of liver metastatic ability, the number of TAMs decreased gradually, with no significant difference between any two of the three groups (P > 0.05), while the numbers of M1 and M2 were significantly decreased and increased, respectively, with significant difference between any two of three groups (P < 0.05 or P < 0.01). In addition, the M2/M1 ratio increased with increase of liver metastatic ability (P < 0.01). There was no statistical significance of correlation of TAMs with each clinical and pathological parameter. M1 was negatively related with lymphatic metastasis and liver metastatic ability. M2 was positively correlated with preoperative CEA level, lymphatic metastasis, tumor differentiation degree and liver metastatic ability. The same was the case for the M2/M1 ratio. Conclusions: Effects of TAMs on liver metastasis of colorectal cancer do not depend on the total number of TAMs, but on the number and proportion of functional subtypes M1 and M2. M2 number and M2/M1 ratio are more accurate predictors for liver metastasis of colorectal cancer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.3
• /
• pp.214-219
• /
• 2000

In this paper the structural dielectric and piezoelectric properties of Pb［(M $g_{1}$2// $W_{1}$2/)$_{x}$-(N $i_{1}$3//N $b_{2}$3/)$_{0.15-x-(Zr_{0.5})}$ $Ti_{0.5}$)$_{0.85}$］ $O_3$ (x=0.0~0.10) ceramic were investigated with the substitution of Pb(M $g_{1}$2// $W_{1}$2/) $O_3$. According to the substitution of Pb(M $g_{1}$2//W/1/2/) $O_3$ curie temperatures were slightly decrease due to the decrease of the tetrag-onality of crystal structure and coercive fields were decreased. Up to the substitution of Pb(M $g_{1}$2// $W_{1}$2/) $O_3$ 3mol%,remnant polarization dielectric constant piezoelectric constant were increased. Dielectric constant and electro-mechanical coupling factor( $k_{p}$, $k_{31}$ ) were appeared the highest value of 2230, 0.64, and 0.38 and piezoelectric constant( $d_{33}$ , $d_{31}$ ) was the largest value of 418, 202($\times$10$^{-12}$ /C/N), respectively, when the substitution amount of Pb(M $g_{1}$2// $W_{1}$2/N) respectively, when the substitution amount of Pb(M $g_{1}$2// $W_{1}$2/) $O_3$ was 3mol%.s 3mol%.%.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.10
• /
• pp.2923-2928
• /
• 2010

This study examined the synthesis of the crystal structure of bis(2,2'-bipyridine)nitrato zinc (II) nitrate, $[Zn(bipy)_2(NO_3)]^+NO_3^-$ using a microwave treatment at 300 W and 60 Hz for the application to dye-sensitized solar cells. The simulated complex structure of the complex was optimized with the density functional theory calculations for the UV-vis spectrum of the ground state using Gaussian 03 at the B3LYP/LANL2DZ level. The structure of the acquired complex was expected a penta-coordination with four nitrogen atoms of bipyridine and the oxygen bond of the $NO_3^-$ ion. The reflectance UV-vis absorption spectra exhibited two absorptions (L-L transfers) that were assigned to the transfers from the ligand ($\sigma$, $\pi$) of $NO_3$ to the ligand ($\sigma^*$, $\pi^*$) of pyridine at around 200 - 350 nm, and from the non-bonding orbital (n) of O in $NO_3$ to the p-orbital of pyridine at around 450 - 550 nm, respectively. The photoelectric efficiency was approximately 0.397% in the dye-sensitized solar cells with the nanometer-sized $TiO_2$ at an open-circuit voltage (Voc) of 0.39 V, a short-circuit current density (Jsc) of $1.79\;mA/cm^2$, and an incident light intensity of $100\;mW/cm^2$.

• Journal of Magnetics
• /
• v.7 no.3
• /
• pp.106-114
• /
• 2002

To reduce the grain size and the media noise in a typical CrMo/CoCrPtB longitudinal media, a sputtering process which includes the exposure of oxygen onto the surface of CrW$_x$ (x=0, 25, 50, 75, 100 at.%) and CrTi$_{15}$ seedlayers with the thickness of 0.5 nm have been utilized. The main results are: (1) the media grain size and the media noise are reduced when using CrW$_x$ (x=0, 25, 50 at.%) seedlayers, and not reduced when using CrTils or CrW$_x$ (x=75, 100 at.%) seedlayers, (2) AES and RHEED results suggest that W seedlayer, which has the highest melting point, forms layer-like film with very small and dense island grain, due to its high free surface energy and low mobility. On the other hand, CrW$_{50}$ and Cr seedlayers, which have lower melting point than W seedlayer, form island film, (3) to effectively reduce the media grain size and improve the media signal to noise ratio, it is essential to utilize a very thin Cr-based seedlayer with high affinity for oxygen and which forms island-like structure, such as CrW$_{50}$ seedlayer.