• 제어로봇시스템학회논문지
• /
• 제18권3호
• /
• pp.230-236
• /
• 2012

Shielding the air-gap magnetic field of the electrodynamic wheel below a conductive plate and opening the shielding plate partially, a thrust force and a normal force generate on the conductive plate at the open area. But, as only the variable controlling both forces is a rotating speed of the electrodynamic wheel, it is very difficult to control the forces independently by the speed. So, we discuss a novel method controlling the forces effectively through manipulating a size of the open area. The independent control is made possible by virtue of the feature that the relative ratio between both forces is irrelevant to an air-gap length and determined uniquely for a specific rotating speed of the wheel. Therefore, the rotating speed and the size of open area become new control variables. The feasibility of the method is verified experimentally. Specially, the controllable magnetic forces are used in a noncontact conveyance of the conductive plate.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.779-783
• /
• 2004

First this paper introduces an advanced FADEC (Full Authority Digital Electric Control) for current and future jet engines.It is designed to realize not only stable thrust control, but also performance improvement, reliability enhancement, service life extension, etc. It can be built by using current micro-processor with high computational power and there exists no difficulties but reliability problem of the micro- processor. Next, the simulation results of SFC minimization control are shown. The target engine is a supersonic, low-bypass ratio, 2-spool, combined cycle turbofan, designated as HYPR90T, which consists of a turbo engine for under Mach 3 flight and a ram engine for over Mach 3 flight. he results can then be used for performance optimization of the engine, which plays important role in the advanced FADEC.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.275-278
• /
• 2010

핀틀형 추력기는 운용 도중에 노즐목 면적을 변경시켜 고체추진기관과 같은 추력기를 액체 추진기관과 같이 추력을 자유자재로 조절할 수 있다. 본 논문에서는 SNECMA사(社)에서 개발한 Divert용 핀틀추력기의 핀틀의 형상 변화에 대해 수치해석 기법으로 분석하였다. Bore에 의하여 핀틀 구동시 받게되는 핀틀의 하중은 줄어들었고, 핀틀 형상에 따라 유동장이 크게 변하는걸 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.1091-1094
• /
• 1993

Recently, in the industrial applications, the direct drive method with linear pulse motor(LPM) has been introduced and studied for practical use. This paper describes the analysis result of hybrid(HB), permanent magnet(PM), and variable reluctance(VR) type LPM. First, calculation of the flux density distribution in the air gap at these LPM by finite element method. And by mean of Maxwell's stress tensor with above magnetic flux density, calcurated the static thrust force and normal force.

• 한국지능시스템학회논문지
• /
• 제20권4호
• /
• pp.476-482
• /
• 2010

본 논문에서는 시간에 따라 종방향 속도가 변하는 무인 수중 잠수정의 경로 추적 제어기 설계 방법을 제안한다. 본 논문에서 제안한 경로 추적 제어기는 운동학적 제어기와 동역학적 제어기로 구성된다. 운동학적 제어기는 무인 수중 잠수정이 시간에 따라 속도가 변하는 기준 경로를 따라 가기 위해 종방향 속도와 yaw 각속도를 계산하고, 계산된 값이 동역학적 제어기의 기준 입력 값이 된다. 즉, 동역학적 제어기는 추진력과 회전력을 제어하여 무인 수중 잠수정의 종방향 속도와 yaw 각속도가 운동학적 제어기에서 계산한 값과 일치하도록 설계한다. 이 때 사용한 동역학적 제어기는 무인 잠수정의 옆 미끄럼 속도를 외란으로 가정하고, 종방향 속도와 yaw 각속도를 슬라이딩 모드 제어 기법을 이용하여 설계한다. 한편 설계된 제어기의 안정도 판별을 위해 Lyapunov 방법을 이용하여 제어기의 안정성을 보인다. 마지막으로, 컴퓨터 시뮬레이션을 이용하여 설계된 제어기의 성능을 검증한다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.513-520
• /
• 2004

A steady-state/transient performance simulation model was newly developed for the propulsion system of the CRW (Canard Rotor Wing) type UAV (Unmanned Aerial Vehicle) during flight mode transition. The CRW type UAV has a new concept RPV (Remotely Piloted Vehicle) which can fly at two flight modes such as the take-off/landing and low speed forward flight mode using the rotary wing driven by engine bypass exhaust gas and the high speed forward flight mode using the stopped wing and main engine thrust. The propulsion system of the CRW type UAV consists of the main engine system and the duct system. The flight vehicle may generally select a proper type and specific engine with acceptable thrust level to meet the flight mission in the propulsion system design phase. In this study, a turbojet engine with one spool was selected by decision of the vehicle system designer, and the duct system is composed of main duct, rotor duct, master valve, rotor tip-jet nozzles, and variable area main nozzle. In order to establish the safe flight mode transition region of the propulsion system, steady-state and transient performance simulation should be needed. Using this simulation model, the optimal fuel flow schedules were obtained to keep the proper surge margin and the turbine inlet temperature limitation through steady-state and transient performance estimation. Furthermore, these analysis results will be used to the control optimization of the propulsion system, later. In the transient performance model, ICV (Inter-Component Volume) model was used. The performance analysis using the developed models was performed at various flight conditions and fuel flow schedules, and these results could set the safe flight mode transition region to satisfy the turbine inlet temperature overshoot limitation as well as the compressor surge margin. Because the engine performance simulation results without the duct system were well agreed with the engine manufacturer's data and the analysis results using a commercial program, it was confirmed that the validity of the proposed performance model was verified. However, the propulsion system performance model including the duct system will be compared with experimental measuring data, later.

• 한국추진공학회지
• /
• 제19권5호
• /
• pp.1-14
• /
• 2015

아음속에서 초음속까지 운용되어야 하는 초음속 터빈엔진의 경우, 엔진 운용 공기량이 범위가 넓고 추력 및 연료소모율 등의 엔진 성능에 대해 요구조건이 높으므로 가변시스템 및 이를 제어하기 위한 최적의 제어로직 개발이 반드시 필요하다. 본 연구에서는 압축기 가변 시스템이 적용된 가스터빈 성능해석 모델 및 제어기법을 개발하였다. 그리고 터빈 노즐 가변에 따른 엔진 운용 특성을 분석하였다. 또한 가변 시스템을 구동하는 액추에이터에 대한 개념 설계를 수행 하였다. 저바이패스비 혼합흐름 터보팬 엔진에 대한 탈설계점에서의 성능해석을 수행하였으며, 제어기법을 적용하여 탈설계점에서의 서지마진을 확보할 수 있었다.

• 한국태양에너지학회 논문집
• /
• 제36권6호
• /
• pp.1-12
• /
• 2016

A control algorithm for a 100 kW wind turbine is designed in this study. The wind turbine is operating as a variable speed variable pitch (VSVP) status. Also, this wind turbine is a permanent magnet synchronous generator (PMSG) Type. For the medium capacity wind turbine considered in this study, it was found that the optimum tip speed ratios to achieve the maximum power coefficients varied with wind speeds. Therefore a commercial blade element momentum theory and multi-body dynamics based program was implemented to consider the variation of aerodynamic coefficients with respect to Reynolds numbers and to find out the power and thrust coefficients with respect tip speed ratio and blade pitch angles. In the end a basic power controller was designed for below rated, transition and above rated regions, and a load reduction algorithm was designed to reduce tower vibration by the nacelle motion. As a result, damage equivalent Load (DEL) of tower fore-aft has been reduced by 32%. From dynamic simulations in the commercial program, the controller was found to work properly as designed. Experimental validation of the control algorithm will be done in the future.

• 한국항공우주학회지
• /
• 제32권4호
• /
• pp.80-87
• /
• 2004

KSR-III 비행용 액체추진제 로켓엔진의 각 성능 변수 간 상관관계를 파악하기 위하여, 엔 진 지상연소시험의 결과에 대한 분석이 수행되었다. 내열재 연소실의 삭마에 따른 변화를 고려하였으며, 산화제/연료비에 의한 변화를 무시한 선형 회귀분석과 이를 포함한 이변수 이차 회귀분석이 수행되었다. 선형 회귀분석은 간단하면서도 분석영역 내에서 1% 이내의 오차율을 가지는 매우 실용적인 방법임을 보여주었다. 또한 이변수 이차 회귀분석 결과는 분석영역 내에서 매우 높은 정확도의 예측이 가능하였으며, KSR-III 엔진의 추력 (혹은 비추력) 및 연소실 압력 (혹은 특성속도)에 대한 최적 산화제/연료비가 각각 2.22 와 2.17 인 것으로 분석되었다.

• 대한조선학회논문집
• /
• 제53권1호
• /
• pp.37-44
• /
• 2016

Recently researchers are conducting a lot of research related to EEDI in order to satisfy IMO resolution MEPC. Especially they are interested in design of energy saving device. This paper is to design the asymmetric pre-swirl stator for 160K LNG carrier in order to reduce energy. Two types of the asymmetric pre-swirl stator are taken into account; constant and variable pitch angle stators. “constant” and “variable” mean state that the pitch of stators change by radius. The dimensions of the stators are initially determined using potential-flow code. The propulsion performances of the stators are predicted using viscous-flow code. The model test is carried out in towing tank in PNU. Prediction of ship performance generally follow ITTC recommended. Ship wake prediction was done by two method, ITTC 1978 and ITTC 1999. Therefore propulsion performances were compared ITTC 1978 with ITTC 1999 methods. Comparison components are delivered power and thrust deduction coefficient of the model. Final pre-swirl stator is selected by comparing experiment and CFD.