현재 대중화 되고 있는 디지털 방송 이후의 발전방향인 Post_HD(High-Definition)서비스로 3DTV(Three Dimensional Television)가 대두되고 있다. 이와 같은 3DTV 서비스는 스테레오스코픽 영상을 구성하는 방법에서 이를 기존의 방송망에서 서비스하기 위한 방법까지 다양한 방법들이 연구되어지고 있다. 본 논문에서는 3DTV 서비스를 제공하기 위한 다양한 비디오 영상의 구성 방법에 모두 적용 가능한 전송방법으로 MPEG-2 전송스트림의 PMT에 스테레오스코픽 기술자를 추가한 방안과 MPEG-C part 3의 확장을 통해 스테레오스코픽 비디오를 전송하는 방안의 분석하여 고화질 스테레오스코픽 비디오 방송서비스 방안을 제안한다. 제안된 기술은 기존의 3D 방송을 지원하지 않는 단말에서도 기준영상만을 출력하여 기존의 MPEG-2 전송스트림과 호환성을 유지하고 있다. 따라서 기존의 디지털 방송과 스테레오 스코픽 영상 서비스 지원이 가능한 규격으로써 향후 통신과 방송 영역에서 스테레오스코픽 기반 3D 서비스 활성화에 기여할 것이다.
이 연구는 한국, 중국, 일본을 포함하는 동아시아 지역의 지각과 최상부맨틀의 SV파 및 SH파 속도구조와 지진파의 속도 방사 이방성(radial anisotropy)을 알아보기 위해 수행하였다. IRIS (Incorporate Research Institutions for Seismology)에서 동아시아에 설치한 광대역 지진관측소에 기록된 지진자료를 사용하여 레일리파와 러브파를 추출하였으며, MFT (Multiple Filter Technique)을 사용하여 각 성분에 기록된 주기 3 ~ 200초 범위의 레일리파와 러브파의 군속도 분산자료를 획득하였다. 수직성분에서 62466개의 레일리파의 분산곡선 측정값을, 접선(transverse)성분에서 54141개의 러브파의 분산곡선 측정값을 얻을 수 있었다. 얻어진 분산자료를 역산하여 속도모델을 구하였고, 역산된 모델을 통해 깊이 100 km 까지의 SV파 및 SH파 속도 구조를 구하였다. SV파와 SH파 속도구조의 경우, 동일하게 깊이 30 km 까지 동해에서 강한 고속도 이상이 나타나며, 30 km 이상의 깊이에서는 중국 남서쪽의 티벳 고원에서 강한 저속도 이상이 나타난다. SH파 속도구조의 경우, 30 km 이상의 깊이에서 동해에서 상대적으로 더 강한 저속도 이상이 나타난다. 그 결과, 지진파 이방성은 평균적으로 동해지역에서 음의 이방성을, 중국 내륙지역에서 양의 이방성이 관측된다.
한국환경과학회 2003년도 International Symposium on Clean Environment
/
pp.177-184
/
2003
Numerical simulation on marine wind and sea surface elevation was carried out using both three-dimensional hydrostatic and non-hydrostatic models and a simple oceanic model from 0900 LST, August 13 to 0900 LST, August 15, 1995. As daytime easterly meso-scale sea-breeze from the eastern sea penetrates Kangnung city in the center part as basin and goes up along the slope of Mt. Taegullyang in the west, it confronts synoptic-scale westerly wind blowing over the top of the mountain at the mid of the eastern slope and then the resultant wind produces an upper level westerly return flow toward the East Sea. In a narrow band of weak surface wind within 10km of the coastal sea, wind stress is generally small, less than l${\times}$10E-2 Pa and it reaches 2 ${\times}$ 10E-2 Pa to the 35 km. Positive wind stress curl of 15 $\times$ 10E-5Pa $m^{-1}$ still exists in the same band and corresponds to the ascent of 70 em from the sea level. This is due to the generation of northerly wind driven current with a speed of 11 m $S^{-1}$ along the coast under the influence of south-easterly wind and makes an intrusion of warm waters from the southern sea into the northern coast, such as the East Korea Warm Current. On the other hand, even if nighttime downslope windstorm of 14m/s associated with both mountain wind and land-breeze produces the development of internal gravity waves with a hydraulic jump motion of air near the coastal inland surface, the surface wind in the coastal sea is relatively moderate south-westerly wind, resulting in moderate wind stress. Negative wind stress curl in the coast causes the subsidence of the sea surface of 15 em along the coast and south-westerly coastal surface wind drives alongshore south-easterly wind driven current, opposite to the daytime one. Then, it causes the intrusion of cold waters like the North Korea Cold Current in the northern coastal sea into the narrow band of the southern coastal sea. However, the band of positive wind stress curl at the distance of 30km away from the coast toward further offshore area can also cause the uprising of sea waters and the intrusion of warm waters from the southern sea toward the northern sea (northerly wind driven current), resulting in a counter-clockwise wind driven current. These clockwise and counter-clockwise currents much induce the formation of low clouds containing fog and drizzle in the coastal region.
Purpose : This study was to assess the loading distributing characteristics of implant systems with internal connection or external connection under vertical and inclined loading using finite element analysis. Materials and methods : Two finite element models were designed according to type of internal connection or external connection The crown for mandibular first molar was made using cemented abutment. Each three-dimensional finite element model was created with the physical properties of the implant and surrounding bone This study simulated loads of 200N at the central fossa in a vertical direction (loading condition A), 200N at the centric cusp tip in a 15$^{\circ}$ inward inclined direction (loading condition B), or 200N at the centric cusp tip in a 30$^{\circ}$ outward inclined direction (loading condition C) respectively. Von Mises stresses were recorded and compared in the supporting bone, fixture, abutment and abutment screw. Results : 1. In comparison with the whole stress or the model 1 and model 2, the stress pattern was shown through th contact of the abutment and the implant fixture in the model 1, while the stress pattern was shown through the abutment screw mainly in the model 2. 2. Without regard to the loading condition, greater stress was taken at the cortical bone, and lower stress was taken at the cancellous bone. The stress taken at the cortical bone was greater at the model 1 than at the model 2, but the stress taken at the cortical bone was much less than the stress taken at the abutment, the implant fixture, and the abutment screw in case of both model 1 and model 2. 3. Without regard to the loading condition, the stress pattern of the abutment was greater at the model 1 than at the model 2. 4. In comparison with the stress distribution of model 1 and model 2, the maximum stress was taken at the abutment in the model 1. while the maximum stress was taken at the abutment screw in the model 2. 5. The magnitude of the maximum stress taken at the supporting bone, the implant fixture, the abutment, and the abutment screw was greater in the order of loading condition A, B and C. Conclusion : The stress distribution pattern of the internal connection system was mostly distributed widely to the lower part along the inner surface of the implant fixture contacting the abutment core through its contact portion because of the intimate contact of the abutment and the implant fixture and so the less stress was taken at the abutment screw, while the abutment screw can be the weakest portion clinically because the greater stress was taken at the abutment screw in case of the external connection system, and therefore the further clinical study about this problem is needed.
Cardiac disease is one of the leading causes of death in Korea. In quantitative analysis of cardiac function and morphological information by three-dimensional reconstruction of magnetic resonance images, left ventricle provides an important role functionally and physiologically. However, existing procedures mostly rely on the extensive human interaction and are seldom evaluated on clinical applications. In this study, we developed a system which could perform automatic extraction of enpicardial and endocardial contour and analysis of cardiac function to evaluate reliability and stability of each system comparing with the result of ARGUS system offered 1.5T Siemens MRI system and manual method performed by clinicians. For various aspects, we investigated reliability of each system by compared with left ventricular contour, end-diastolic volume (EDV), end-systolic volume (ESV), stock volume (SV), ejection fraction (EF), cardiac output (CO) and wall thickness (WT). When comparing with manual method, extracted results of developed process using minimum error threshold (MET) method that automatically extracts contour from cardiac MR images and ARGUS system were demonstrated as successful rate 90% of the contour extraction. When calculating cardiac function parameters using MET and comparing with using correlation coefficients analysis method, the process extracts endocardial and epicardial contour using MET, values from automatic and ARGUS method agreed with manual values within :t 3% average error. It was successfully demonstrated that automatic method using threshold technique could provide high potential for assessing of each parameters with relatively high reliability compared with manual method. In this study, the method developed in this study could reduce processing time compared with ARGUS and manual method due to a simple threshold technique. This method is useful for diagnosis of cardiac disease, simulating physiological function and amount of blood flow of left ventricle. In addition, this method could be valuable in developing automatic systems in order to apply to other deformable image models.
3차원적 정량적인 구조-활성관계(3D-QSARs: CoMFA 및 CoMSIA)에 기초하여 phytoene desaturase (PDS)에 대한 O-(2-phenoxy)ethyl-N-aralkylcarbamate 유도체(1-15)의 제초성 평가를 위한 R-phenoxy 치환기들의 구조적인 요건들을 정량적으로 검토하였다. CoMFA 1 모델의 예측성 및 상관성($r^2_{cv.}=0.753$ 및 $r^2_{ncv.}=0.964$)이 나머지 모델들보다 높았다. 최적화된 CoMFA 1 모델로부터 PDS 저해활성은 O-(2-phenoxy)ethyl-N-aralkylcarbamate 유도체들의 입체장(44.0%), 정전기장(36.3%) 및 소수성장(19.6%)에 의존적이었다. CoMFA 등고도 분석결과, phenoxy 고리상 meta-와 para-위치에는 입체적으로 큰 치환기, meta-위치는 음하전, para-위치의 바깥 부분에는 양하전, ortho- 및 para- phenoxy 고리 중앙의 바깥 부분에는 친수성 치환기가 그리고 meta-위치에 소수성 R-치환기가 각각 도입될 경우에 PDS에 대한 저해활성이 증가할 것으로 예측되었다.
Kim, Byung-Soo;Edler, Lutz;Park, Jin-Joo;Fournier, Dietrich Von;Haase, Wulf;Sautter-Bihl, Mare-Luise;Hagmuller, Egbert;Gotzes, Florian;Thielmann, Heinz Walter
Toxicological Research
/
제20권2호
/
pp.89-100
/
2004
The comet assay (also called the single-cell gel electrophoresis assay) has been widely used for detecting DNA damage and repair in individual cells. Since the conventional methods of evaluating comet assay data using frequency statistics are unsatisfactory we developed a new quantitative measure of DNA damage/repair that is based on all information residing in the dose/time-response curves of a comet experiment. Blood samples were taken from 25 breast cancer patients before undergoing radiotherapy. The comet assay was performed under alkaline conditions using isolated lymphocytes. Tail DNA, tail length, tail moment and tail inertia of the comet were measured for each patient at four doses of $\gamma$-rays (0, 2, 4 and 8 Gy) and at four time points after irradiation (0, 10, 20 and 30 min) using 100 cells each. The resulting three-dimensional dose-time response surface was modeled by multiple regression, and the second derivative, termed 2D, on dose and time was determined. A software module was programmed in SAS/AF to compute 2D values. We applied the new method successfully to data obtained from cancer patients to be assessed for their radiation sensitivity. We computed the 2D values for the four damage measures, i.e., tail moment, tail length, tail DNA and tail inertia, and examined the pairwise correlation coefficients of 2D both on the log scale and the unlogged scale. 2D values based on tail moment and tail DNA showed a high correlation and, therefore, these two damage measures can be used interchangeably as far as DNA repair is concerned. 2D values based on tail inertia have a correlation profile different from the other 2D values which may reflect different facets of DNA damage/repair. Using the dose-time response surface, other statistical models, e.g., the proportional hazards model, become applicable for data analysis. The 2D approach can be applied to all DNA repair measures, Le., tail moment, tail length, tail DNA and tail inertia, and appears to be superior to conventional evaluation methods as it integrates all data of the dose/time-response curves of a comet assay.
작물 모델의 개발과 검증에 사용되는 생체중 자료는 파괴적 샘플링을 통해 얻어져 왔다. 파괴적 샘플링이 가지는 단점을 보완하기 위해 저가형 3D 센서인 Kinect 센서와 무료 공개 소프트웨어들을 사용하여 생체중을 추정하는 기법을 개발하였다. 특히, 많은 작물모델들이 개발되어 있지 않은 배추를 대상으로 입체이미지를 생성하여, 그로부터 얻어진 부피와 생체중 추정치의 신뢰도를 분석하고자 하였다. 크기가 다른 배추 결구 부위를 스캔하기 위해 Kinect 센서와, Microsoft가 무상으로 제공하는 Software Development Kit 내 Kinect Fusion Explorer 프로그램을 사용하였다. 개별 배추의 입체이미지를 생성하기 위해 3D 그래픽 편집 소프트웨어인 Meshlab을 활용하여 배경과 불필요한 물체를 수동으로 제거하였다. 또한, 불완전한 입체모델로부터 생체중 추정을 위해 3D 프린터 소프트웨어인 Makerbot Desktop 을 사용하여 배추를 생성하기 위해 필요한 플라스틱 필라멘트 소모량을 추정하였다. 입체모델 편집 프로그램인 Blender를 사용하여 부피를 추정하였을 때, 실제 부피에 비해 17.6%에서 2160.6% 범위의 상당한 오차가 있었다. 반면, 필라멘트 소요량은 실제 배추 생체중 변이의 98.7%를 설명할 수 있었다. 또한, 이들의 상관관계는 5% 수준에서 유의하였다. 이러한 결과들은 직접적인 부피 계산 절차를 제외하더라도 간편하게 생체중을 추정할 수 있음을 확인하였다. Kinect 센서를 사용하여 배추의 생체중 추정이 가능하다는 것이 확인 되었으나, 기존의 고가형 3D 센서에 비해 낮은 해상도와 주간에 활용이 어려운 점이 있다. 그럼에도 불구하고, 배추 생육 모델의 시계열적 검증 자료를 Kinect 센서를 이용하여 간편하고 신속하게 획득할 수 있어 모델의 불확도를 감소하는 데에 기여할 수 있을 것으로 판단된다. 따라서, 후속 연구에서 보다 저렴한 가격대의 3D 센서들을 대상으로 야외 및 주간조건애서 작물의 생체중 측정 가능성에 대해 검토하고 작물 모형 개발 및 개선을 위한 기술개발이 이루어져야 할 것으로 사료된다.
연안에서 표사문제의 대책을 장기적인 관점에서 수립하기 위해서는 연안에서의 표사뿐만 아니라 배후지 하천으로부터 유출되는 유사량을 포함한 종합적인 토사관리 필요성이 증가하고 있다. 이와 같은 관점에서 본 연구에서 연안해역으로 유출되는 하천 유사의 이송, 하구에서 사주발생과 발달 및 하구폐색, 연안으로 유출된 유사의 저류문제, 홍수 시 외해로 유출되는 유사의 특성 등에 대해 검토하였다. 최근 울산 회야강 하구에 하구폐색과 하구사주의 발생에 따른 대책으로 1997년부터 2004년에 걸쳐 총연장 156m의 도류제를 건설하였다. 이에 따라 회야강 하구에서 도류제 건설에 따른 토사이동 특성이 변히고 있음에 따라 해저지형 변동과 표사이동을 해석하기 위하여 1차원 수치해석을 수행하였다. 이를 위해 먼저 울산 회야강 하구역에서 유출하는 유사량을 3가지 모래가 혼합되어 있다고 가정한 혼합입경의 관점을 가정하였다. 그리고 회야강 하구인근의 파동장, 해빈류장 및 표사이동 특성을 Bailard(1981)의 에너지 모형에 의해 해저지형 변동 특성을 해석하였다. 또, 하구폐색의 변동특성을 확인하기 위하여 항공사진을 통한 회야강 하구 및 진하 해수욕장 인근 지형변화를 비교하였다.
Restorative procedures can lead to weakening tooth due to reduction and alteration of tooth structure. It is essential to prevent fractures to conserve tooth. The resistance to fracture of the restored tooth may be influenced by many factors, among these are the cavity dimension and the physical properties of the restorative material. The placement of direct composite resin restorations has generally been found to have a strengthening effect on the prepared teeth. It is the purpose of this investigation to study the relationship between the cavity isthmus and the fracture resistance of a tooth in composite resin restorations. In this study, MO cavity was prepared on maxillary first premolar. Three dimensional finite element models were made by serial photographic method and isthmus(1/4, 1/3, 1/2 of intercuspal distance) were varied. Two types of model(B and R model) were developed. B model was assumed perfect bonding between the restoration and cavity wall and R model was left unfilled. A load of 500N was applied vertically at the first node from the lingual slope of the buccal cusp tip. This study analysed the displacement, 1 and 2 direction normal stress and strain with FEM software ABAQUS Version 5.2 and hardware IRIS 4D/310 VGX Work-station. The results were as follows : 1. Displacement of buccal cusp in R model occurred and increased as widening of the cavity, and displacement in B model was little and not influenced by cavity width. 2. There was a significant decrease of stress resulting in increase of fracture resistance in B model when compared with R model. 3. With the increase of the isthmus width, B model showed no change in the stress and strain. In R model, the stress and strain increased both in the area of buccal-pulpal line angle and the buccal side of marginal ridge, therefore the possibility of crack increased. 4. The stress and strain were distributed evenly on the tooth in B model, but in R model, were concentrated on the buccal side of the distal marginal ridge and buccal-pulpal line angle, therefore the possibility of fracture increased.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.