• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.362-367
• /
• 2023

Recently, research and development of proton exchange membrane fuel cells (PEMFC) membranes are progressing in the direction of thinning to reduce prices and improve performance. Demand for hydrogen-powered vehicles for commercial vehicles is also increasing, and their durability should be five times greater than those for passenger vehicles. Despite the thinning of the membranes, the durability of the membranes must be increased five times, so the improvement of the durability of the membranes has become more important. Since the acceleration durability evaluation time also needs to be shortened, the protocol using oxygen instead of air in the existing protocol was applied to a 10 ㎛ thin membrane to evaluate durability. The accelerated durability test (Open circuit voltage holding) was terminated at 720 hours. If the air-based department of energy (DOE) protocol was used, a lifespan of 450,000 km of driving hours would be expected, with a durability of about 1,500 hours. During the chemical durability evaluation, the active area of the electrode decreased by 51%, suggesting that catalyst degradation had an effect on membrane durability. Reducing the catalyst degradation rate is expected to increase membrane durability.

• Progress in Medical Physics
• /
• v.2 no.2
• /
• pp.183-192
• /
• 1991

Ophthalmoscopy following the intravenous injection of fluorescein has gained great diagnostic importance in ophthalmology. This technique provides sequential evaluation of the anatomic and physiologic status of the choroidal and retinal vasculature. In order to detect the changes between fluorescein ocular fundus image frames, the direct subtraction of the two frames is inadequate because of geometric distortions and background gray level differences in two images. In this study, a scheme for the correction of the geometric distortions is proposed. Precise control point coordinate values for transformation functions are manually determined after the process including a series of blood vessel detection and thinning, and one frame is mapped to another, and then a geometric distortion corrected image is obtained. When the corrected image is used in interframe change detections, a sucessful result is ensured.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.11
• /
• pp.55-61
• /
• 2009

The wall thinning defect of nuclear power pipe is mainly occurred by the affect of the flow accelerated corrosion (FAC) of fluid. This type of defect becomes the cause of damage or destruction of in carbon steel pipes. Therefore, it is very important to measure defect which is existed not only on the welding part but also on the whole field of pipe. This study use dual-beam Shearography, which can measure the out-of-plane deformation and the in-plane deformation by using another illuminated laser beam and simple image processing technique. And this study proposes Infrared thermography, which is a two-dimensional non-contact nondestructive evaluation that can detect internal defects from the thermal distribution by the inspection of infrared light radiated from the object surface. In this paper, defect of nuclear power pipe were, measured using dual-beam shearography and infrared thermography, quantitatively evaluated by the analysis of phase map and thermal image pattern.

• International Journal of Quality Innovation
• /
• v.6 no.3
• /
• pp.204-215
• /
• 2005

This paper explores innovative manufacturing processes, which can be used to manufacture the national musical instrument of Trinidad and Tobago, the Musical Steel Drum or Steel Pan. The main manufacturing process used today is the manual hand-forming technique. In order to achieve more consistent and deeper formed components while maintaining the high quality of the instrument, it is proposed that the Marforming process and the Flow-forming process, an adaptation of the Spinforming process, be used more frequently in the future to replace the traditional Hand-forming method. In the traditional Spinforming technique material is pushed from the outer circumference of the metal disc to the center in progressive passes of the former. This results in a thinning of the outer region of the formed component with thickening of the center, however the opposite is required for the musical steel drum and by adapting the process the required strain distributions were achieved. Evaluation took the form of strain analyses of pre-formed steel drums and visual inspection of the quality of the surface finish. It was found that the Marformed components had the smallest range of strain values while the Spinformed components had the largest range.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.12 s.255
• /
• pp.1618-1625
• /
• 2006

During the last two decades, several guidelines have been developed and used for assessing the integrity of a defective steam generator (SG) tube that is generally caused by stress corrosion cracking or wall-thinning phenomenon. However, as some of SG tubes are also failed due to fretting and so on, alternative failure estimation schemes are required for relevant defects. In this paper, parametric three-dimensional finite element (FE) analyses are carried out under internal pressure condition to simulate the failure behavior of SG tubes with different defect configurations; elliptical wear, tapered and flat wear type defects. Maximum pressures based on material strengths are obtained from more than a hundred FE results to predict the failure of SG tube. After investigating the effect of key parameters such as defect depth, defect length and wrap angle, simplified failure estimation equations are proposed in relation to the equivalent stress at the deepest point in wear region. Comparison of failure pressures predicted by the proposed estimation scheme with corresponding burst test data showed a good agreement.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.8
• /
• pp.826-831
• /
• 2009

The piping systems in nuclear power plant are composed of various typed pipes such as straight, elbow pipe, branch and reducer etc. The elbow is connected from straight pipe to another pipes in order to establish the complicated piping system. Elbow is one of very important components considering management of wall thinning degradation. It is however applied by various loads such as system pressure, earthquake, postulated break loading and many transient loads, which provoke simply the internal pressure, bending and torsional stress. In this study, firstly pipes in the secondary system of the nuclear power plant are classified as pipe size and type for selecting the investigating range. Next, a large number of finite element analysis considering the all typed dimensions of commercial pipe has been performed to find out the behavior of TES(twice elastic slop) plastic load of elbows, which is based on evaluation of the structural safety factor. Finally performance based structural safety factor was investigated comparing with maximum allowable load by construction code.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.6
• /
• pp.453-459
• /
• 2015

In this paper, we propose a new digit recognition method based on opened enclosure. In the proposed method, each digit is divided into two parts, an upper part and a lower part, which are based on a cutting line that is modified depending on the number of intersection points. In the simulation, the performance evaluation through the data acquisition and application of the proposed algorithm was carried out and the result was presented.

• Archives of Plastic Surgery
• /
• v.50 no.2
• /
• pp.171-176
• /
• 2023

Background Human bite wounds in emergency department need evaluation in regard of reconstruction. These are due to occlusive bite injuries over face. Most commonly, human bites over face involve ear and nose, and may lead to avulsion injury. Defects over nose can be reconstructed immediately after debridement or delayed till the wound heals and scar becomes supple. Thorough wash and lavage with broadspectrum antibiotic cover has utmost importance in preventing cartilage infection. Methods We report 20 cases of human bite injuries over nose who presented to us in emergency department between 2018 and 2020. At the time of presentation the wound was assessed for closure. If not possible, patient was planned for delayed reconstruction after 3 months. In case delayed reconstruction was planned, the skin and nasal mucosa were approximated at first presentation. The patients underwent paramedian forehead flap after recreation of defect with conchal cartilage graft. Second stage of flap detachment and insetting was done after 3 weeks. After three weeks of second stage, third stage of flap thinning was done. Patients were followed for 3-6 months and subjective satisfaction was noted. Results Nineteen patients underwent delayed staged reconstruction with paramedian forehead flap and one underwent primary wound closure. The flap survival was 100%. The patient satisfaction was excellent in most cases. Conclusion We recommend delayed reconstruction for human bite nasal injuries. For reconstruction, paramedian forehead flap with conchal cartilage graft, if required, provides excellent reconstructive option with good contour and color match and minimal donor site scar.

• Journal of Biosystems Engineering
• /
• v.36 no.1
• /
• pp.40-47
• /
• 2011

Image analysis algorithm for the quality evaluation of ginseng seedling was investigated. The images of ginseng seedling were acquired with a color CCD camera and processed with the image analysis methods, such as binary conversion, labeling, and thinning. The processed images were used to calculate the length and weight of ginseng seedlings. The length and weight of the samples could be predicted with standard errors of 0.343 mm, and 0.0214 g respectively, $R^2$ values of 0.8738 and 0.9835 respectively. For the evaluation of the three quality grades of Gab, Eul, and abnormal ginseng seedlings, features from the processed images were extracted. The features combined with the ratio of the lengths and areas of the ginseng seedlings efficiently differentiate the abnormal shapes from the normal ones of the samples. The grade levels were evaluated with an efficient pattern recognition method of support vector machine analysis. The quality grade of ginseng seedling could be evaluated with an accuracy of 95% and 97% for training and validation, respectively. The result indicates that color image analysis with support vector machine algorithm has good potential to be used for the development of an automatic sorting system for ginseng seedling.

• Journal of Korean Society of Forest Science
• /
• v.88 no.3
• /
• pp.309-319
• /
• 1999

This study was conducted to get forest scenic beauty management information toward forest working systems; characteristics in Larix forest stands. 35 different alternatives were simulated to visualize on basis of actual forest working methods. The options were illustrated as photos produced by computer software. Each alternatives were evaluated by 3 groups with total 593 respondents after reliability test. Visual preference evaluation was used 1 - 10 point rating scale. The ratings were scaled using SBE analysis program of RMRATE. To compare the relationship of visual preference and image scale, Spatial images of 13 thinning alternatives were measured by Semantic differential scale. In general, the respondents preferred refreshing and ordering forest stand after forest working to natural forest stand before forest working. Visual preference decreased with the increasing intensity of bare ground area and slash area in forest stand. And also, visual preference was high related to tree density, clear length of stem, and ground vegetation. Farm line of small clear cutting area was preferred straight line to curve line. Visual preferences were significant differences in certain socioeconomic variables of the respondents. Results indicate how to conduct forest working system for forest scenic beauty management.