• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.481-488
• /
• 2008

A detail design of overhead catenary system can be divided into a pegging plan and a design of MD(mounting diagram). In the pegging plan, the mast location, staggering and tension length are determined in the longitudinal point of view according to track condition, location of substation and etc. In the MD, a transversal diagram including masts, all of wires, cantilever, foundation and etc. and materials used are shown. This study presents a development of a software to design the MD for a conventional catenary system automatically. In the program, thin walled steel pole, foundation, cantilever, all of wires and etc. are automatically drawn according to the input and catenary conditions. And materials used in the MD and the section can be also managed respectively in the program. This application of the program is developed using C# for input/calculating and using C++(ObjectARX) for drafting the MD, respectively.

• Nuclear Engineering and Technology
• /
• v.48 no.4
• /
• pp.1009-1014
• /
• 2016

SiC-based ceramic composites are currently being considered for use in fuel cladding tubes in light-water reactors. The joining of SiC ceramics in a hermetic seal is required for the development of ceramic-based fuel cladding tubes. In this study, SiC monoliths were diffusion bonded using a Ti foil interlayer and additional Si powder. In the joining process, a very low uniaxial pressure of ~0.1 MPa was applied, so the process is applicable for joining thin-walled long tubes. The joining strength depended strongly on the type of SiC material. Reaction-bonded SiC (RB-SiC) showed a higher joining strength than sintered SiC because the diffusion reaction of Si was promoted in the former. The joining strength of sintered SiC was increased by the addition of Si at the Ti interlayer to play the role of the free Si in RB-SiC. The maximum joint strength obtained under torsional stress was ~100 MPa. The joint interface consisted of $TiSi_2$, $Ti_3SiC_2$, and SiC phases formed by a diffusion reaction of Ti and Si.

• Journal of Veterinary Clinics
• /
• v.29 no.5
• /
• pp.427-430
• /
• 2012

An infertile, three-year-old primiparous cow was diagnosed preliminarily with pyometra by rectal palpation at 180 days postpartum. Ultrasonography showed that the cranial portion of the right uterine horn was distended with fluid, while the base portion of the horn was missing. A dense band of tissue connected the cranial portion of the uterine horn to the uterine body. However, the left uterine horn was normal. Gross postmortem analysis of the reproductive organs confirmed the ultrasonographic observations. Histopathological observations also showed that dark red-brown mucus filled the thin-walled right uterine horn, where neither caruncles nor uterine glands were observed. Finally, this primiparous Holstein cow was diagnosed with segmental aplasia of the right uterine horn.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.1
• /
• pp.233-241
• /
• 2005

The paper is presented experimental study results on bond stress between profiled steel and concrete in Profiled SPC(Profiled Steel Plate Concrete) rectangular steel tubes through an experimental program in which 13 pull-out specimens were tested. Advantages and class of composite members and current problems of construction work are noted, past research of PSSC is described. An experimental study is described and evaluated. The bond capacity is interrelated with slip at the steel concrete interface. The factors influencing the mechanism of bond stress transfer were the cross section shape, length/diameter, diameter/thickness and environmental parameters (temperature, moisture). The results of experimental program indicated that the force transfer could be characterized into two regions The first region was governed by bond with no relative slip between the profiled steel and concrete. The second region occurs after the chemical debonding. Bond stress transfer in this region was governed by frictional resistance between profiled steel and concrete and cross section shapes. The important factors influencing the magnitude of frictional resistance are the profiled steel shapes, length/diameter and environmental parameters. (temperature, moisture)

• Journal of the korean academy of Pediatric Dentistry
• /
• v.27 no.4
• /
• pp.485-489
• /
• 2000

A mucocele is a thin-walled, bluish, fluctuant swelling occurring just beneath the oral mucosa and filled with mucoid material. It usually results from damage to a salivary gland following which there is extravasation of mucus into the tissues, or occasionally it forms from dilatation of the duct of a salivary gland. The accepted treatment of a mucocele is excision of the sac and the associated minor salivary gland. Use of the $CO_2$ laser in oral surgery has several advantages. It is a very precise means of cutting tissue and causes little adjacent nontarget tissue damage. There is excellent coagulation of small blood vessels and consequently operative hemorrhage is greatly decreased. There is instant sterilization of the operative site, which decreases bacteremia. The operation sites were completely healed without any infection or complication and discomfort from swelling or pain was not noted in all cases throughout the healing process. In addition, following this therapy, there is little contraction or scarring.

• Tuberculosis and Respiratory Diseases
• /
• v.78 no.4
• /
• pp.371-374
• /
• 2015

Pulmonary pneumatoceles are air-filled thin-walled spaces within the lung and are rare in adult cases of pneumonia. We report the case of a 74-year-old male who was admitted with a cough and sputum production. He had been treated with oral dexamethasone since a brain tumorectomy 6 months prior. Contrast-enhanced computed tomography (CT) of the chest revealed a large pneumatocele in the right middle lobe and peripheral pneumonic consolidation. Bronchoalveolar lavage was performed; cultures identified extended-spectrum ${\beta}$-lactamase (ESBL) producing Proteus mirabilis. A 4-week course of intravenous ertapenem was administered, and the pneumatocele with pneumonia resolved on follow-up chest CT. To the best of our knowledge, this is the first reported case of pulmonary pneumatocele caused by ESBL-producing P. mirabilis associated with pneumonia.

• Computational Structural Engineering
• /
• v.7 no.3
• /
• pp.133-141
• /
• 1994

When a bolt is tightened up to the range of plastic deformation, yielding may be governed by the combined stresses due to the axial force developed in the bolt and the frictional torque induced on the thread by the contact with the nut. Consideration is taken account of the fact that the unengaged portion of the thread has least sectional area, being subject to initial yielding. Once yielding has taken place some strain hardening effect may result. Incremental stress-strain relations are used to treat the continued yielding, which is equivalent to treat continued yielding as if summing up the effects of thin walled cylinders subject to plastic deformation. M10 bolts of fine threads are used for both computational and experimental purposes. Variation of axial forces and frictional torques vs. the frictional coefficients are presented together with other plots showing some characterist of bolt under plastic deformation. Finally, a design and control aid for the tightening(i.e., kind of nomograph) is presented, showing the relationships among the torque factor and frictional coefficients for that particular bolt used in the experiment.

• Structural Engineering and Mechanics
• /
• v.24 no.6
• /
• pp.709-725
• /
• 2006

In this paper the buckling and post-buckling behavior of slender bars under self-weight are studied. In order to study the post-buckling behavior of the bar, a geometrically exact formulation for the non-linear analysis of uni-directional structural elements is presented, considering arbitrary load distribution and boundary conditions. From this formulation one obtains a set of first-order coupled nonlinear equations which, together with the boundary conditions at the bar ends, form a two-point boundary value problem. This problem is solved by the simultaneous use of the Runge-Kutta integration scheme and the Newton-Raphson method. By virtue of a continuation algorithm, accurate solutions can be obtained for a variety of stability problems exhibiting either limit point or bifurcational-type buckling. Using this formulation, a detailed parametric analysis is conducted in order to study the buckling and post-buckling behavior of slender bars under self-weight, including the influence of boundary conditions on the stability and large deflection behavior of the bar. In order to evaluate the quality and accuracy of the results, an experimental analysis was conducted considering a clamped-free thin-walled metal bar. As this kind of structure presents a high index of slenderness, its answers could be affected by the introduction of conventional sensors. In this paper, an experimental methodology was developed, allowing the measurement of static or dynamic displacements without making contact with the structure, using digital image processing techniques. The proposed experimental procedure can be used to a wide class of problems involving large deflections and deformations. The experimental buckling and post-buckling behavior compared favorably with the theoretical and numerical results.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.156-161
• /
• 2004

To predict the direction of the fatigue crack initiated from a hole under various types of biaxial fatigue loads with different phase difference and biaxiality, fatigue parameters were investigated. Axial and torsional biaxial fatigue loads were selected with the respective combination of five different phase differences of 0, 45, 90, 145 and 180 degrees and five biaxialities of 0, $1/{\sqrt{3}}$, 1, ${\sqrt{3}}$, ${\infty}$. Directions of the fatigue crack initiation around the hole were found to approach to the circumferential direction of the specimen with increment of the phase difference for fatigue tests with phase differences less than $90^{\circ}$. Whereas directions for tests with phase differences greater than $90^{\circ}$ went away from the circumferential direction and those were symmetric to the directions for tests with phase difference less than $90^{\circ}$. With increase of biaxilities, the fatigue crack initiated more apart from the circumferential direction of the specimen. These crack initiation direction were predicted using maximum tangential stress range and maximum shear stress range obtained at far-field and around the hole. Comparing these two stress parameters, The crack initiation direction can be successfully explained by using the direction of the maximum tangential stress range obtained around the hole and at far-field.

• Tuberculosis and Respiratory Diseases
• /
• v.42 no.4
• /
• pp.624-628
• /
• 1995

Lymphangioleiomyomatosis is a rare disease which afflicts young women of childbearing age. We experienced a 32-year-old female who was admitted because of worsening exertional dyspnea after hormonal therapy with Clomifen for five months and intermittent hemoptysis. Chest PA showed diffuse ground glass appearance with some reticular infiltrations. High resolution CT scan showed multiple small thin walled cysts distributed homogeneously throughout the entire lung. Pulmonary function test showed characteristic obstructive pattern despite the restrictive interstitial pattern of chest radiography. Thoracoscopic lung biopsy specimen showed abnormal proliferation of smooth muscle cells in the walls of lymphatic vessels, bronchioles, and pulmonary vessels typical of pulmonary lymphangioleiomyomatosis. Hormonal therapy with medroxyprogesterone was initiated.