• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1430-1432
• /
• 1997

A solar cell conversion effiency was degraded by grain boundary effect in polycrystalline silicon. To reduce these effects of the grain boundaries, we investigated various influencing factors such as preferential chemical etching of grain boundaries, grid design, transparent conductive thin film, and top metallization along grain boundaries. Pretreatment in $N_2$ atmosphere and gettering by $POCl_3$ and Al were performed to obtain polycrystalline silicon of the reduced defect density. Structural, electrical, and optical properties of solar cells were characterized. Improved conversion efficiencies of solar cell were obtained by a combination of Al diffusion into grain boundaries on rear side, fine grid finger, top Yb metal grid on Cr thin film of $200{\AA}$ and buried contact metallization along grain boundaries.

• Journal of the Korean Solar Energy Society
• /
• v.28 no.3
• /
• pp.21-26
• /
• 2008

Solar cells are renewable energy source which is not only environmentally friendly but also economically viable. For that matter, thin film materials are in observed with great in terest by a number of sources throughout the nations. Among these, CdTe (Cadium telluride) and CIS (copper indium diselenide) are the latest commercial products that are gathering attention in the solar cells markets. However there are some downsides to this newly invention. Since the materials are embedded, in the occasion of damage, certain amount of module residue can be released to water or soil. This paper outlines the results of our outdoor leaching experiments on photovoltaic (PV) samples broken into small fragments and been observed for 1 year.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.3
• /
• pp.75-79
• /
• 2009

An intrinsic silicon thin film passivation layer is deposited by the microwave remote-plasma enhanced chemical vapor deposition at temperature of $175^{\circ}C$ and various gas ratios for solar cell applications. The good quality amorphous silicon films were formed at silane $(SiH_4)$ gas flow rates above 15 seem. The highest effective carrier lifetime was obtained at the $SiH_4$, flow rate of 20 seem and the value was about 3 times higher compared with the bulk lifetime of 5.6 ${\mu}s$ at a fixed injection level of ${\Delta}n\;=\;5{\times}10^{14}\;cm^{-3}$. An annealing treatment was performed and the carrier life times were increased approximately 5 times compared with the bulk lifetime. The optimal annealing temperature and time were obtained at 250 $^{\circ}C$ and 60 sec respectively. This indicates that the combination of the deposition of an amorphous thin film at a low temperature and the annealing treatment contributes to the excellent surface and bulk passivation.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1598-1600
• /
• 2003

Microcrystalline silicon(c-Si:H) thin-film solar cells are prepared with intrinsic Si-layer by hot wire CVD. The operating parameters of solar cells are strongly affected by the filament temperature ($T_f$) during intrinsic layer. Jsc and efficiency abruptly decreases with elevated $T_f$ to $1400^{\circ}C$. This deterioration of solar cell parameters are resulted from increase of crystalline volume fraction and corresponding defect density at high $T_f$ The heater temperature ($T_h$) are also critical parameter that controls device operations. Solar cells prepared at low $T_h$ (<$200^{\circ}C$) shows a similar operating properties with devices prepared at high $T_f$, i.e. low Jsc, Voc and efficiency. The origins for this result, however, are different with that of inferior device performances at high $T_f$. In addition the phase transition of the silicon films occurs at different silane concentration (SC) by varying filament temperature, by which highest efficiency with SC vanes with $T_f$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.99.1-99.1
• /
• 2010

Many efforts on the surface sulfurization of $Cu(InGa)Se_2$ (CIGS)thin films have been reported as techniques to improve CIGS solar cell performance. We have investigated the sulfurization technique using the sulfur vapor. The co-evaporated $Cu(In,Ga)Se_2$ tin film was used for sulfurization. A thin $Cu(In,Ga)(S,Se)_2$ layer was grown on the surface of the CIGS thin film after high-temperature annealing in sulfur vapor. The structural and compositional properties of the thin films were studied by XRD, EDS and AES analysis. The obtained results revealed that the surface modification technique is promising method to S incorporated into CIGS absorber.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.2
• /
• pp.14-19
• /
• 2013

The size and distribution of residual stresses and the effect of the minimum mesh size were investigated by the a-Si thin film solar cell. Attributed to the difference in coefficient of thermal expansion of the a-Si and Ag concentrated residual stresses at the joint interface of dissimilar materials. The ${\sigma}y$ and ${\tau}xy$ didn't appear in the central part, but ${\sigma}x$ existed. However, ${\sigma}x$, ${\sigma}y$ and ${\tau}xy$ appeared in the edge part and concentrated residual stresses at the interface between a-Si and Ag. Minimum mesh size gets smaller, the concentration of ${\sigma}y$ was significantly and existence area was reduced. As a result, the failure of thin film solar cells during the cutting process can be explained by the residual stresses.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.465-466
• /
• 2009

Dye-sensitized Solar Cell (DSC) is a new type of solar cell by using photocatalytic properties of $TiO_2$. The electric potential distribution in DSCs has played a major role in the operation of such cells. $TiO_2$ thin films were deposited on the ITO substrate by Nd:YAG Pulsed Laser Deposition(PLD) at room temperature and post-deposition annealing at $500^{\circ}C$ in flowing $O_2$ atmosphere for 1hour. The structural properties of $TiO_2$ thin films have investigated by X-ray diffraction(XRD). We manufactured DSC unit cells then I-V and efficiency were tested by solar simulator.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.83-84
• /
• 2009

Thin film solar cells based on CIGS continue to be a leading candidate for thin film photovoltaic devices due to their appropriate bandgap, long-term stability, and low-cost production. To date, the most successful technique for the deposition of a CIGS absorber layer has been based on the co-evaporation However, the evaporation process is difficult to scale-up for large-area manufacturing the sputtering and Selenizaton process has been a promising method for low-cost and large-scale production of high quality CIGS In this study, we have used Cu and CuIn alloy targets for precursor deposition the precursor deposited by sputtering Cu and CuIn targets and $CuInSe_2$ thin film is manufactured by Selenization process

• Laser Solutions
• /
• v.14 no.3
• /
• pp.1-6
• /
• 2011

Globally, the interest of renewable energy has become an upsurge. Especially, the solar industry is the one which is getting rapid growth rate. Many of researchers have been undertaking to improve the efficiency of solar cell to accomplish grid parity. The most of research has been concentrated on two methods, one on the selective emitter and the other is on LBSF (Local Back Surface Field) formation. Laser patterning will be needed to eliminate the thin film to form selective emitter and LBSF of solar cell. This paper reports some experimental results in laser patterning process for high-efficiency crystalline solar cell manufacturing. The experimental results indicate that the patterning quality depends on the average power and repetition rate of laser. The experimental results prove that the laser patterning process is an advantageous method to improve the efficiency of solar cell.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.243-243
• /
• 2007