• Membrane Journal
• /
• v.24 no.4
• /
• pp.317-324
• /
• 2014

It is very well known that the conventional polyamide (PA) thin film composite (TFC) reverse osmosis (RO) membranes have excellent permselective properties, but their chlorine tolerance is not good enough. In this study, to improve such chlorine tolerance, microporous membranes containing hydrophilic functional groups such as -COOH were used as a support to prepare PA TFC RO membranes, employing the conventional interfacial polymerization method. Meta-phenylene diamine (MPD) and 2,6-diamine toluene (2,6-DAT) were used as diamine monomers and tri-mesoyl chloride (TMC) as an acid monomer. The membranes prepared were characterized using various instrumental analytical methods and permeation test set-up. The flux obtained from the membranes prepared so was more than $1.0m^3/m^2day$ at 800 psi of operating pressure, while the salt rejection was over 99.0%. The chlorine tolerance of them was also found to be better than that of the membrane prepared by using conventional polysulfone support without hydrophilic functional groups.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.4
• /
• pp.303-310
• /
• 2017

Pressure retarded osmosis(PRO) has attracted much attention as potential technology to reduce the overall energy consumption for reverse osmosis(RO) desalination. The RO/PRO hybrid process is considered as the most logical next step for future desalination. The PRO process aims to harness the osmotic energy difference of two aqueous solutions separated by a semipermeable membrane. By using the concentrated water(RO brine) discharged from existing RO plants, the PRO process can effectively exploit a greater salinity gradient to reduce the energy cost of processing concentrated water. However, in order to use RO brine as the draw solution, PRO membrane must have high water flux and enough mechanical strength to withstand the high operational pressure. This study investigates the development of a thin film composite PRO membrane and spiral wound module for high power density. Also, the influence of membrane backing layer on the overall power density was studied using the characteristic factors of PRO membranes. Finally, the performance test of an 8-inch spiral wound module was carried out under various operating conditions(i.e. hydraulic pressure, flow rate, temperature). As the flow rate and temperature increased under the same hydraulic pressure, the PRO performance increased due to the growth of water permeability coefficient and osmotic pressure. For a high performance PRO system, in order to optimize the operating conditions, it is highly recommended that the flow pressure be minimized while the flow rate is maintained at a high level.

• Journal of the Korean Applied Science and Technology
• /
• v.22 no.3
• /
• pp.281-288
• /
• 2005

The silica nanoparticles were used as support of catalyst, filling material, electronic assembler, thin film material, and sensor material. And, the titania nanoparticles were used as pigment, dielectric substance, sensor and photocatalyst. In this paper, the spherical composite particles of $TiO_2/SiO_2$with narrow size distribution and phase pure were synthesized by ultrasonic spray pyrolysis method from $TiOSO_4$ and colloidal silica solution. Using ultrasonic apparatus, this starting solution was vaporized to droplets, and these droplets were induced into tube furnace by carrier gas. The resulting composite powder was characterized by scanning electron microscopy, X-ray diffraction analysis, TG-DTA, in vitro sun protection factor(SPF) and BET surface area analysis.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.136-141
• /
• 2007

This paper introduces an artificial neuron which is a nano composite continuous sensor. The continuous nano sensor is fabricated as a thin and narrow polymer film sensor that is made of carbon nanotubes composites with a PMMA or a silicone matrix. The sensor can be embedded onto a structure like a neuron in a human body and it can detect deteriorations of the structure. The electrochemical impedance and dynamic strain response of the neuron change due to deterioration of the structure where the sensor is located. A network of the long nano sensor can form a structural neural system to provide large area coverage and an assurance of the operational health of a structure without the need for actuators and complex wave propagation analyses that are used with other methods. The artificial neuron is expected to effectively detect damage in large complex structures including composite helicopter blades and composite aircraft and vehicles.

• Composites Research
• /
• v.20 no.2
• /
• pp.27-31
• /
• 2007

"Structural surface becomes an antenna." This term, CAS, indicates antenna embedding in structural surfaces. The CAS is composed of several composite laminates and Nomex honeycombs, and microstrip antenna elements are inserted between layers with designed configurations. Constituent materials are selected considering electrical contributions as well as mechanical performances. Antenna design with adhesive films are impossible because of their thin and rough distributions between honeycomb and substrate. Therefore, adhesive effects on antenna performances in CAS are experimentally investigated, CAS with targeted impedance and radiation characteristics are designed considering adhesive effects. multilayer

• Textile Coloration and Finishing
• /
• v.34 no.1
• /
• pp.58-67
• /
• 2022

In this study, self-reinforced composite(SRC) was prepared using HDPE(High density polyethylene) fabric(2×2 plain) and LDPE(Low density polyethylene) film. The optimal conditions were derived by manufacturing specimens according to the temperature of 100 ~ 140℃ using a hot stamping at a pressure of 100bar for 10 minutes in order to find the optimal conditions for the SRC. The manufactured SRC was analyzed for tensile properties, compressive strength and shear strength through a universal testing machine(UTM). As a result of the measurement, the P3 specimen prepared by hot stamping at a temperature of 130℃ and a pressure of 100bar for 10 minutes was found to be higher than other specimens with tensile strength and tensile modulus of 210MPa and 19GPa, compressive strength 69MPa and shear strength 13MPa and it was considered to be optimal condition. Finally, the composite material according to the fabric structure was modeled using experimental values and the physical properties of the composite material according to the fabric structure were predicted using GeoDict and Digimat.

• Journal of the Korean Ceramic Society
• /
• v.29 no.6
• /
• pp.496-504
• /
• 1992

Alumina tubes suitable for the support of gas separation membranes have been prepared by the slipcasting technique. These supports have the average pore size of 0.1 ${\mu}{\textrm}{m}$ within the narrow distribution. The sol-gel dipcoating process of nanoparticulate sols is very sensitive to microstructure of the support, and the coating on the inside surface of the tube is found to be more successful than on the outside surface. Nanoparticulate silica sols (0.82 mol/ι) have been synthesized by an interfacial hydrolysis reaction between TEOS and high alkaline water. When coating an alumina tube with these sols, the minimum limits of the particle size and the aging time required for forming the coated gel layer at the given pH are provided. It is optimum to coat the support with less concentrated sols stabilized through aging for the appropriate time (more than 22 days) at the lower pH (pH 2.0) for producing a reproducible crack free thin film coating in composite membranes.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.3
• /
• pp.51-55
• /
• 2014

Ni-CNT(Carbon Nanotubes) composite coating is often used for the surface treatment of mechanical/electronic devices to improve the properties of the Ni coating. For the Ni-CNT coating, the dispersion of CNT fibers is a critical process. In this study, ultrasonic treatment instead of the conventional ball milling was attempted as a dispersion method for the electroless Ni-CNT coating. SEM-EDX analysis was performed and contact angle, sheet resistance, and micro-hardness were measured. Results showed that the ultrasonic treatment was comparable to the ball milling, as a dispersion method, but the difference was negligible. However, combined ball milling and ultrasonic treatment(double treatment) showed much improved micro-hardness value, above 350Hv(close to the value obtained by the Ni-CNT electroplating). In addition, electroless Ni-CNT(double-treated) coatings formed on the thin Ni film deposited by the electroless plating(double coating) showed better mechanical properties. Thus, double treatment and double coating are suggested as an improved electroless Ni-CNT coating method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.214-215
• /
• 2006

Colloidal Silica(CS)와 유기수지를 혼합하여 서로의 단점을 보완하는 나노복합재료를 합성하기 위해 친수성인 CS를 유기실란으로 표면처리하여 소수성화하고 유기수지와 복합체를 제조하였다. CS표면의 -OH기와 실란의 -OH기가 축합반응하여 화학결합을 형성함으로서 CS의 표면은 실란의 $CH_3$에 의해 소수성화되어 CS sol이 제조된다. CS sol과 유기수지는 공동용매에 의해 균일한 분산이 가능하고 필름 및 코팅제로의 제조가 가능하다. 사용된 무기물은 40nm 의 크기를 가지므로 가시광선영역의 빛을 산란하지 않아 투명하고 사용된 수지 또한 투명하여 우수한 광학적 특성을 나타낸다. 만들어진 필름은 CS의 영향으로 유기수지의 내열성보다 향상된 열분해온도와 높은 접촉각, 높은 절연율을 보였다.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2006.03a
• /
• pp.613-619
• /
• 2006

This paper introduces a new structural health monitoring using a nano sensor. The sensor is made of nano smart composite material based on carbon nanotubes. The nano sensor is fabricated as a thin and narrow polymer film sensor that is bonded or deposited onto a structure. The electrochemical impedance and dynamic strain response of the neuron change due to deterioration of the structure where the sensor is located. A network of the long nano sensorcan form a structural neural system to provide large area coverage and an assurance of the operational health of a structure without the need for actuators and complex wave propagation analyses that are used with other methods.