• 한국재료학회지
• /
• 제19권1호
• /
• pp.24-27
• /
• 2009

Indium Gallium Zinc Oxide (IGZO) thin films were deposited onto 300 nm-thick oxidized Si substrates and glass substrates by direct current (DC) magnetron sputtering of IGZO targets at room temperature. FESEM and XRD analyses indicate that non-annealed and annealed IGZO thin films exhibit an amorphous structure. To investigate the effect of an annealing treatment, the films were thermally treated at $300^{\circ}C$ for 1hr in air. The IGZO TFTs structure was a bottom-gate type in which electrodes were deposited by the DC magnetron sputtering of Ti and Au targets at room temperature. The non-annealed and annealed IGZO TFTs exhibit an $I_{on}/I_{off}$ ratio of more than $10^5$. The saturation mobility and threshold voltage of nonannealed IGZO TFTs was $4.92{\times}10^{-1}cm^2/V{\cdot}s$ and 1.46V, respectively, whereas these values for the annealed TFTs were $1.49{\times}10^{-1}cm^2/V{\cdot}$ and 15.43V, respectively. It is believed that an increase in the surface roughness after an annealing treatment degrades the quality of the device. The transmittances of the IGZO thin films were approximately 80%. These results demonstrate that IGZO thin films are suitable for use as transparent thin film transistors (TTFTs).

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.443-443
• /
• 2012

We fabricated a-IGZO TFT with AZO/Ag/AZO transparent multilayer source/drain contacts by rf magnetron sputtering. Enhanced electrical device performance of a-IGZO TFT with AZO/Ag/AZO multilayer S/D electrodes (W/L = = 400/50 mm) was achieved with a subs-threshold swing of 3.78 V/dec, a minimum off-current of 10-12 A, a threshold voltage of 1.80 V, a field effect mobility of 10.86 cm2/Vs, and an on/off ration of 9x109. It demonstrated the potential application of the AZO/Ag/AZO film as a promising S/D contact material for the fabrication of the high performance TFTs.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2004년도 제27회 학술발표회 초록집
• /
• pp.146-146
• /
• 2004

• Journal of Information Display
• /
• 제12권4호
• /
• pp.213-217
• /
• 2011

Printing technologies were applied to fabricate a flexible organic thin-film transistor (OTFT) backplane for electrophoretic displays (EPDs). Various printing processes were adopted to maximize the figures of each layer of OTFT: screen printing combined with reverse offset printing for the gate electrodes and scan bus lines with Ag ink, inkjet for the source/drain electrodes with glycerol-doped Poly (3,4-ethylenedioxythiophene): Poly (styrenesulfonate) (PEDOT:PSS), inkjet for the semiconductor layer with Triisopropylsilylethynyl (TIPS)-pentacene, and screen printing for the pixel electrodes with Ag paste. A mobility of $0.44cm^2/V$ s was obtained, with an average standard deviation of 20%, from the 36 OTFTs taken from different backplane locations, which indicates high uniformity. An EPD laminated on an OTFT backplane with $190{\times}152$ pixels on an 8-in panel was successfully operated by displaying some patterns.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.441-445
• /
• 2007

In this paper we demonstrated the applications of OTFTs (organic thin film transistors) to flexible displays such as AM-EPD (active matrix electrophoretic display) and AM-OLED (active matrix organic light emitting diode), and also to integrated circuits. The OTFTs using pentacene semiconductor layer and PVP gate dielectric and Au S/D electrodes exhibited good performance for AM-EPD with the mobility of $0.59\;cm^{2}/V.sec,$ and with also good uniformity over 2.5" diagonal area. However, it is nor enough for AM-OLED requiring the mobility larger than $1\;cm^{2}/V.sec$ for large area displays. The integrated circuits also worked, producing the operating frequency of 1MHz. We need to develop a fabrication process to reduce parasitic capacitance for high frequency operation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 춘계학술대회 논문집
• /
• pp.63-64
• /
• 2009

The TFTs have been fabricated with 3 different geometry SID electrodes which have the same channel W/L ratio (W/L = 5) due to constant channel resistance, The 3 samples have different channel widths (350, 150, and $25\;{\mu}m$) and channel lengths (70, 30, and $5\;{\mu}m$) by fixed channel W/L ratio simultaneously on one chip for reliable comparisons. Resultant on-current and field effect mobility are proportional to the channel width, while the subthreshold swing is inversely proportional to the channel width mainly due to the change of contact resistance. These results show that the contact resistance strongly affects the device performances and should be considered in the applications.

• 한국전기전자재료학회논문지
• /
• 제22권9호
• /
• pp.747-750
• /
• 2009

The TFTs have been fabricated with 3 different geometry SID electrodes which have the same channel W/L ratio (W/L = 5) due to constant channel resistance, The 3 samples have different channel widths (350, 150, and 25 ${\mu}m$) and channel lengths (70, 30, and 5 ${\mu}m$) by fixed channel W/L ratio simultaneously on one chip for reliable comparisons. Resultant on-current and field effect mobility are proportional to the channel width, while the subthreshold swing is inversely proportional to the channel width mainly due to the change of contact resistance. These results show that the contact resistance strongly affects the device performances and should be considered in the applications.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.479-479
• /
• 2011

Flexible inverters based on complementary thin-film transistor (CTFTs) are important because they have low power consumption and other advantages over single type TFT inverters. In addition, integrated CTFTs in flexible electronic circuits on low-cost, large area and mechanically flexible substrates have potentials in various applications such as radio-frequency identification tags (RFIDs), sensors, and backplanes for flexible displays. In this work, we introduce flexible complementary inverters using pentacene and amorphous indium gallium zinc oxide (IGZO) for the p-channel and n-channel, respectively. The CTFTs were fabricated on polyimide (PI) substrate. Firstly, a thin poly-4-vinyl phenol (PVP) layer was spin coated on PI substrate to make a smooth surface with rms surface roughness of 0.3 nm, which was required to grow high quality IGZO layers. Then, Ni gate electrode was deposited on the PVP layer by e-beam evaporator. 400-nm-thick PVP and 20-nm-thick ALD Al2O3 dielectric was deposited in sequence as a double gate dielectric layer for high flexibility and low leakage current. Then, IGZO and pentacene semiconductor layers were deposited by rf sputter and thermal evaporator, respectively, using shadow masks. Finally, Al and Au source/drain electrodes of 70 nm were respectively deposited on each semiconductor layer using shadow masks by thermal evaporator. Basic electrical characteristics of individual transistors and the whole CTFTs were measured by a semiconductor parameter analyzer (HP4145B, Agilent Technologies) at room temperature in the dark. Performance of those devices then was measured under static and dynamic mechanical deformation. Effects of cyclic bending were also examined. The voltage transfer characteristics (Vout- Vin) and voltage gain (-dVout/dVin) of flexible inverter circuit were analyzed and the effects of mechanical bending will be discussed in detail.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.465-468
• /
• 1999

Electrical properties of metal-ferroelectric-semiconductor field effect transistor(MFSFET) using $BaMgF_4$ thin films grown on p-Si(100) substrates have been investigated. $BaMgF_4$ thin films have been directly deposited on the p-Si(100) wafers at a low temperature of $300^{\circ}C$ in an ultra high vacuum(UHV) system. First an in-situ post-deposition annealing was conducted for 20s at $650^{\circ}C$ and second an in-situ post-annealing was conducted for 10s at $950^{\circ}C$. The electrical properties of MFSFET compared with using A1 and Pt electrodes.

• 대한전자공학회논문지SD
• /
• 제47권8호
• /
• pp.7-12
• /
• 2010

본 논문에서는 BPhen(Bathophenanthroline)과 BPhen에 Cs가 도핑 된 interlayer를 $C_{60}$활성층과 Al전극사이에 주입해 $C_{60}$을 기반으로 한 유기박막트랜지스터 (OTFTs)를 제작하여 전기적 특성을 향상시켰다. BPhen층을 증착하면 유기물과 금속층계면의 표면 거칠기가 낮아져 결과적으로 성능이 향상되는 것을 알 수 있었다. 또한 BPhen에 Cs가 도핑 된 interlayer를 co-evaporation을 이용하여 주입하였을 경우는 Contact resistance가 감소하였다. 이러한 $C_{60}$을 기반으로 한 BPhen에 Cs가 도핑 된 interlayer를 삽입한 유기박막트랜지스터는 향후 n형 유기박막트랜지스터를 제작하는데 있어서 적용이 될 것이라고 기대된다.