• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.281-282
• /
• 2005

The AZO thin film was prepared on flexible substrate by Facing Targets Sputtering method. The substrate used the Polycarbonate(PC), thickness 200$\mu$m. In particular, the AZO thin film was prepared at room temperature because the substrate is weak in heat. The structural, electrical, optical properties of the AZO thin film were investigated and the surface was observed by microscope.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2006년도 춘계학술대회
• /
• pp.164-167
• /
• 2006

In this paper, we prepared Al doped ZnO thin films by using facing targets sputtering method. Al doped ZnO thin film was deposited with different working pressure on flexible substrate. We prepared Al doped ZnO thin film at room temperature, because the flexible substrate has weak thermal resistance. From the results, we could obtain thin film with a resistivity of $8.4{\times}10^{-4}{\Omega}cm$, an average transmittance of over 80% and a film thickness of 200nm.

• 한국결정성장학회지
• /
• 제26권6호
• /
• pp.220-224
• /
• 2016

초음파 스프레이를 이용하여 유리기판 위에 반사방지 박막이 제조되었다. GPTMS와 TEOS는 솔-젤 하이브리드 코팅 용액을 제조하기 위하여 사용되었다. 반사방지막의 코팅 두께를 제어하기 위하여 스프레이 노즐의 이동속도는 15~25 mm/s로 변경되었다. 스프레이 노즐의 이동속도가 증가 됨에 따라 반사방지막의 두께는 138 nm에서 86 nm로 감소되었다. 20 mm/s의 노즐 이동속도에 의해 제조된 반사방지막의 굴절률은 약 1.31, 막의 두께는 104 nm이며, 380 nm에서 780 nm의 가시광 영역에서의 평균 반사율은 0.75 %, 투과율은 94 %로 측정되었다.

• 센서학회지
• /
• 제18권2호
• /
• pp.110-115
• /
• 2009

Polystyrene (PS) microspheres were used to good advantage as a template material to prepare macroporous $TiO_2$ thin films. This is enabled to run the thermal decomposition of the PS without the collapsing of the 3-D macroporous framework during the calcination step. $TiO_2$ thin films were deposited onto the colloidal templated substrates at room temperature by RF sputtering, and then samples were thermally treated at $450^{\circ}C$ for 40.min in air to remove the organic colloidal template and induce crystallization of the $TiO_2$ film. The macroporous $TiO_2$ thin film exhibited a quasi-ordered partially hexagonal close-packed structure. Burst holes, estimated to be formed during PS thermal decomposition, are seen as the hemisphere walls. the inner as well as the outer surfaces of the hollow hemispheres formed by the method of thermal decomposition can be easily accessed by the diffusing gas species. As a consequence, the active surface area interacting with the gas species is expected to be enlarged about by a factor of fourth as large as compared to that of a planar films. Also the thickness at neighboring hemisphere could be controlled a few nm thickness. If the acceptor density becomes as large that depletion width reaches those thickness, the device is in the pinch off-situation and a strong resistance change should be observed.

• 센서학회지
• /
• 제24권6호
• /
• pp.364-367
• /
• 2015

Tin oxide thin films were fabricated on glass substrates by the successive ionic layer adsorption and reaction (SILAR) method at room temperature and ambient pressure. Before measuring their properties, all samples were annealed at $500^{\circ}C$ for 2 h in air. Film thickness increased with the number of cycles; X-ray diffraction patterns for the annealed $SnO_2$ thin films indicated a $SnO_2$ single phase. Thickness of the $SnO_2$ films increased from 12 to 50 nm as the number of cycles increased from 20 to 60. Although the optical transmittance decreased with thickness, 50 nm $SnO_2$ thin films exhibited a high value of more than 85%. Regarding electronic properties, sheet resistance of the films decreased as thickness increased; however, the measured resistivity of the thin film was nearly constant with thickness ($3{\times}10^{-4}ohm/cm$). From Hall measurements, the 50 nm thickness $SnO_2$ thin film had the highest mobility of the samples ($8.6cm^2/(V{\cdot}s)$). In conclusion, optical and electronic properties of $SnO_2$ thin films could be controlled by adjusting the number of SILAR cycles.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권8호
• /
• pp.813-818
• /
• 1996

Amorphous As$_{10}$Ge$_{15}$ Te$_{75}$ device shows the memory switching characteristics under d.c. bias. In bulk material, a-As$_{10}$Ge$_{15}$ Te$_{75}$ switching threshold voltage (V$_{th}$) is very high (above 100 volts), but in the case of thin film, V$_{th}$ decreases to a few or ten a few volts. The characteristics of V$_{th}$ depends on the physical dimensions such as the thickness of thin film and the separation between d.c. electrodes, and the annealing conditions. The switching threshold voltage decreases exponentially with increasing annealing temperature and annealing time, but increases linearly with the thickness of thin film and exponentially with increasing the separation between d.c. electrodes. The desirable low switching threshold voltage, therefore, can be obtained by the stabilization through annealing and changing physical dimensions.imensions.sions.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권2호
• /
• pp.129-135
• /
• 1995

SiO thin films are deposited by evaporator the refractive index of wave length, photon energy and the absorptive rate of these films are measured by spectroscopic ellipsometer. It is derived the absorptive rate and permitivity of SiO thin films from the equations that calculating the refractive index. And the result show good agreement with the calculated values and experimental values. As a result, the wave length of light is increased in the condition that the angle of incidence is fixed on SiO thin film, the basic absorption and the absorption impurities are found in the low wave length (below 450 nm in this study) and the reflective absorption and conductive absorption is increased by the form of exponential function over the low wavelength. The absorptive rate is increased by increased the angle of incidence and thickness of SiO film for the insulating layer. As the thickness of SiO film is increased, the value of complex permitivity is decreasing and as wave length of incidence is increased., the value of dielectric is linearly increasing.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2005년도 추계 학술대회
• /
• pp.93-96
• /
• 2005

In this study, AZO(ZnO:Al) thin film were Prepared by FTS(Facing Target Sputtering) system. The electrical, optical properties and crystalline of AZO thin film with thickness have been investigated. The thickness, transmittance, crystalline and electrical Properties of AZO thin film were measured by $\alpha$-step, UV-VIS spectrometer, hall effect measurement system, XRD and four-point probe, respectively. As a result, AZO thin film deposited with the transmittance over $80\%$ and the resistivity about $10^{-4}{\Omega}-cm$.

• 한국재료학회지
• /
• 제11권4호
• /
• pp.319-323
• /
• 2001

펄스레이저 증착법 (PLD)으로 (0001)면 사파이어 기판 위에 성장시킨 ZnO 박막의 두게 변화가 표면형상, 결정성 및 전기/광학적 특성에 미치는 효과에 대하여 조사하였다. SEM 및 XRD 분석을 통해 약 4000 의 두께에서 3차원 island들이 생성되며, 박막의 두께가 증가함에 따라 결정립의 크기가 증가하고, 결정성이 향상되었음을 알 수 있었다 상온에서의 PL 측정을 통해 두께가 증가함에 따라 ultraviolet(UV) 및 deep level emission peak의 강도가 급격히 증가함을 알 수 있었다. Hall측정 결과, 모든 박막들이 H형 전도도를 보였고, 운반자농도가 $10^{19}$ $cm^{-3}$ 이상이었으며, 두께가 증가할수록 운반자농도가 감소하여 약 4000 에서 포화되는 경향을 보였다. 따라서, 사파이어 기판 위에 증착시킨 ZnO 박막은 약 4000 의 두께에서 bulk ZnO의 특성을 나타내었다.

• 한국정밀공학회지
• /
• 제20권4호
• /
• pp.143-150
• /
• 2003

Frictional properties of ultra-thin carbon coatings on silicon wafer were investigated based on Taguchi experimental design method. Sensitivity analysis was performed with normal load, relative humidity, deposition process, and coating thickness as the variables. It was found that despite low thickness, the carbon coating resulted in relatively low friction coefficient. Also, the frictional behavior was affected significantly by humidity and normal load.