• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.362-365
• /
• 2007

In wind turbine blades, airfoils are required to have different spec when compared with airplane airfoil. Airfoils for wind turbine blade must have a high lift-to-drag ratio, moderate to high lift and especially low roughness sensitivity. Also an operation Re. No.s are lower than conventional airplane airfoils. At mid-span and inboard region, structural problems have to be considered. Especially, for stall regulated type, moderate stall behavior is essential part of design. For these reasons, airfoil design for HAWT blade is essential part of blade design. In this paper, root airfoil and tip airfoil are discussed. For a root region, 24% thickness airfoil is designed and for a top region, 12% thickness ratio is done. A inverse design method and panel method are used for rapid airfoil design. In this paper, a design method, features of airfoil shape and characteristics are discussed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.5
• /
• pp.321-327
• /
• 2016

This paper presents the application of airfoil impeller for enhancement of aerodynamic performance of a high speed centrifugal fan. Three airfoil impellers are proposed, considering the maximum thickness and the location of maximum thickness of the airfoil. C4 airfoil thickness distribution is applied to the three airfoil impellers. The impellers are evaluated using CFD (computational fluid dynamics) and suction power test. From the results, it is confirmed that flow separations on the pressure side of the impeller blades and the pressure side of diffuser blades are reduced when airfoil blade is applied to the impellers. It is also confirmed that with the centrifugal fan having airfoil impellers, there is an increase in fan efficiency by approximately 3% and reduction in specific sound level by approximately 1.3 dB(A).

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.203-208
• /
• 2016

In this paper, vibration characteristics in terms of the airfoil cross-sectional shape was examined by using the EDISON co-rotational plane beam-transient analysis. Assuming aircraft wing as a cantilevered beam with a constant cross-sectional shape, natural frequencies of each airfoil shape was compared while varying airfoil maximum thickness and maximum camber length, using Fast Fourier Transformation(FFT). When the airfoil maximum thickness was varied, natural frequency showed peak value at 18% chord, and decreased afterwards. When the airfoil maximum camber length was varied, natural frequency either increased or decreased at 6% chord, while at 8% the natural frequency showed its maximum. Applying such trends to B-737 wing airfoil, an improved B-737_mod airfoil shape was obtained with regard to the vibration characteristics.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.6
• /
• pp.475-484
• /
• 2012

Numerical investigation is performed to understand the effects of thickness uncertainty of a supporting airfoil due to manufacturing processes on the aerodynamic characteristics of an airfoil used for measuring data in a wind tunnel testing. This is done by comparing the coefficients of lift, drag and moment of the airfoils. In this work, the airfoil model consists of three parts, one located in the center for measuring and two outer parts used for supporting. The study is carried out with a NACA64-418 airfoil and the turbulence model of Transition SST. It is found that the effect of thickness uncertainty of the airfoils used for supporting is not significant to the performance of the test airfoil at various angles of attack and Reynolds numbers.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.354-357
• /
• 2008

Drag reduction is one of main concerns for commercial aircraft companies than ever because fuel price has been tripled in ten years. In this research, Natural Laminar Flow airfoil is designed and tested to reduce drag at cruise condition, $c_l$=0.3, Re=3.4${\times}$10$^6$ and M=0.6. NLF airfoil is characterized by delayed transition from laminar to turbulent flow, which comes from maintaining favorable pressure gradient to downstream. Transition is predicted by solving Boundary Layer equations in viscous boundary layer and by solving Euler Equation outside the boundary layer. Once boundary layer thickness and momentum thickness are obtained, $e^N$-method is used for transition point prediction. As results, KARI's NLF airfoil is designed and shows better characteristics than NLF-0115. The characteristics are tested and verified at low Reynolds numbers, but at high Reynolds numbers, laminar flow characteristics are not obtainable because of fully turbulent flow over airfoil surfaces. Precious experiences, however, relating NLF airfoil design, subsonic and transonic tests are acquired.

• Proceeding of EDISON Challenge
• /
• 2014.03a
• /
• pp.562-567
• /
• 2014

본 연구에서는 교육 및 연구를 위한 CFD 해석 프로그램인 EDISON_CFD를 이용하여 Symmetric airfoil(NACA0012)과 Cambered airfoil(NACA4412)의 뒷전 두께에 따른 공력 특성을 분석해보았다. Chord 길이의 0%, 1%, 2%, 3%, 4%에 해당하는 뒷전 두께를 가지는 Blunt trailing edge airfoil의 받음각에 따른 공력 특성을 비교 및 분석하고, 어떠한 장단점을 가지는지 확인하였다. 그 결과 Chord 길이의 1% 뒷전 두께를 가질 때를 제외하면 뒷전 두께가 두꺼워질수록 최대양력계수는 증가하였고, 양항비와 실속각은 감소하였다. 또한, 뒷전 두께가 두꺼워질수록 Symmetric airfoil에서는 받음각 $0^{\circ}$를 기준으로 양력곡선기울기가 증가하였고, Cambered airfoil에서는 전체적으로 양력계수가 증가함과 동시에 양력곡선기울기 또한 증가하는 것을 확인할 수 있었다.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.632-637
• /
• 2016

This study shows what difference would be made to the aerodynamic characteristic with different thickness ratio of the same airfoil, Eppler 387, at low Reynolds number, at the angle of attack of $0^{\circ}$. Konkuk Univ.'s airfoil has a bigger thickness ratio than that of the original Eppler 387 airfoil. The reason for the thicker camber is a Pt 100 ohm heater mounted inside the Konkuk Univ.'s airfoil and this was assumed to make some differences to aerodynamic characteristic. The comparison of these two airfoils' CFD data, provided by EDSION_CFD, with real experiment that had been made in subsonic wind tunnel at Konkuk Univ. is done. A finer result would come out if the complement of the homogeneity of the wind tunnel's fluid is done in the future.

• 한국전산유체공학회:학술대회논문집
• /
• 1997.10a
• /
• pp.61-65
• /
• 1997

A two-dimensional airfoil under ground effect in subsonic turbulent flow is calculated by sieving the Navier-Stokes equation. Some numerical results for different NACA four-digit airfoils are presented. The numerical results show that the lift and drag coefficients are strongly influenced by the shape of the region between the lower surface of airfoil and the ground In general, the airfoil with large camber and small thickness is suitable for WIG vehicles

• Advances in Computational Design
• /
• v.7 no.1
• /
• pp.69-79
• /
• 2022

In this research, the aeroelastic instability of a tail section manufactured from aluminum isotropic material with different shell thickness investigated. For this purpose, the two degrees of freedom flutter analytical approach are used, which is accompanied with simulation by finite element analysis. Using finite element analysis, the geometry parameters such as the center of mass, the aerodynamic center and the shear center are determined. Also, by simulation of finite element method, the bending and torsional stiffnesses for various thickness of the airfoil section are determined. Furthermore, using Lagrange's methods the equations of motion are derived and modal frequency and critical torsional/bending modes are discussed. The results show that with increasing the thickness of the isotropic airfoil section, the flutter and divergence speeds increased. Compared of the obtained results with other research, indicates a good agreement and reliability of this method.

• Wind and Structures
• /
• v.22 no.5
• /
• pp.595-616
• /
• 2016

Providing high starting torque and efficiency simultaneously is a significant challenge for vertical axis wind turbines (VAWTs). In this paper, a new approach is studied in order to modify VAWTs performance and cogging torque. In this approach, J-shaped profiles are exploited in the structure of blades by means of eliminating the pressure side of airfoil from the maximum thickness toward the trailing edge. This new profile is a new type of VAWT airfoil using the lift and drag forces, thereby yielding a better performance at low TSRs. To simulate the fluid flow of the VAWT along with J-shaped profiles originated from NACA0018 and NACA0030, a two-dimensional computational analysis is conducted. The Reynolds Averaged Navier-Stokes (RANS) equations are closed using the two-equation Shear Stress Transport (SST) turbulence model. The main objective of the study is to investigate the effects of J-shaped straight blade thickness on the performance characteristics of VAWT. The results obtained indicate that opting for the higher thickness in J-shaped profiles for the blade sections leads the performance and cogging torque of VAWT to enhance dramatically.