• 펄프종이기술
• /
• 제34권4호
• /
• pp.22-29
• /
• 2002

This research was conducted to investigate the morphological characteristics of fine fibers produced during beating process of high yield pulp treated with ozone and the distribution of lignin in the produced fine fibers. Thermomechanical(TMP) pulp and chemithermomechanical(CTMP) pulp of spruce and CTMP of white birch were beaten to reach 200$m\ell$ CSF, and then the fine fibers were observed using ultraviolet microscope. The fine fibers produced from TMP and CTMP of spruce using treated with ozone for 15 minutes were fragments of fiber surfaces or cell corners, and most of them contained lignin. However, lignin was not observed in the fibers after 15 minutes of ozone treatment. The fine fibers produced from CTMP of white birch were broken pieces or fragments of fiber surfaces or cell corners. The lignin was observed in the fibers until 5min of ozone treatment but no lignin was observed after 5 minutes of ozone treatment. Different morphological characteristics of TMP and CTMP explained both the different morphological characteristics and the distribution of lignin observed in the fine fibers produced from the beating process of TMP and CTMP treated with ozone.

• 열처리공학회지
• /
• 제4권2호
• /
• pp.9-18
• /
• 1991

Among the many maunfactured processes of producing multi filamentary composites, in situ process is widely used owing tv its simplicity and easyness of mass production. In this study, the mechanical and electromagnetic properties of Cu-Fe composite materials was investigated. The tensile strength of the Cu-Fe wires increased as the Fe content and reduction ratio were increased. The Cu-30 wt%Fe composites had the best properties in terms of figure merits compared to the other Cu-Fe composites made in this study or the commercially manufactured 6/1 ACSR cables of Cu cable. The coercivity was decreased by increasing Fe content, but the squareness was increased greatly. As increasing reduction ratio, the coercivity and squareness increased up to the maximum points, and then decreased. For example, the maximum values were obtained at $0.09mm{\phi}$ for Cu-30 wt%Fe composites and at $0.066mm{\phi}$ for Cu-45 wt%Fe composites. The magnetic property of Cu-Fe wires produced by precipitation treatment was higher than that of Cu-Fe wires produced by thermomechanical treatment. By annealing Cu-Fe wires after drawing process, the coercivity, remanence and squareness were improved.

• 폴리머
• /
• 제34권5호
• /
• pp.480-484
• /
• 2010

무수산인 4,4'-(4,4'-isopropylidene-diphenoxy)bis(phthalic anhydride)(BPADA)와 아민계인 2,2'-bis(trifluoromethyl)benzidine(TFB), bis(3-aminophenyl)sulfone(APS), 4,4'-methylene-bis-(2-methylcyclohexylamine)(MMCA), bis[4-(3-aminophenoxy)phenyl]sulfone(BAPS)에 melamine을 각각 5 몰%로 반응시켜 N,N'-dimethylacetamide(DMAc) 용매 속에서 폴리아믹산(poly(amic acid), PAA)들을 얻었다. 용액 상태의 PAA를 캐스팅하여 각각 다른 반응 온도에서 열처리를 통해 무색 투명한 폴리이미드(PI) 필름을 얻었다. PI의 열적 성질, 광학적 특성을 다양한 아민 구조의 변화에 따라 조사하였으며, 열적 성질은 differential scanning calorimetry(DSC), thermogravimetric analysis(TGA), thermomechanical analysis(TMA)를 이용해 측정하였고, 광학적 투명도는 색차계(spectrophotometry)를 이용하였다. 제조된 모든 필름의 열 팽창계수는 $48.53-64.24ppm/^{\circ}C$ 사이의 값을 얻었으며, 모든 필름 시료의 노란색 지수(yellow index, YI)는 3 이하를 나타내었다.

• 한국세라믹학회지
• /
• 제35권2호
• /
• pp.137-144
• /
• 1998

고온초전도체 61심 Bi-2223 선재간의 초전도 접합부위를 화학적 부식 및 열적· 기계적 반복 공정에 의하여 제조하였다. 초전도 선재 테이프의 은 피복재 한쪽 표면을 초전도체와 반응하지 않는 부식액(NH4OH:H2O2=1:1)으로 화학적으로 제거한 다음, 두 시편을 일출가압 성형하여 접합시편을 제조하였고 일련의 서로 다른 열적· 기계적 처리를 거쳐 접합부의 물성 및 미세구조를 분석하였다. 접합부를 따라 임계전류(Ic) 변화와 전류전압 곡선의 특성을 측정하기 위하여 여러 단자를 접합부 주위에 설치하여 부위별 I~V 특성을 측정한 결과 단심선재에 비하여 다심선재에서 선재 전체의 통전 능력을 좌우하는 천이구간의 임계전류값이 높았다. 그러나 단심에 비해 다심선재는 천이급속도를 나타내는 n값이 다심선재내 각각의 초전도 core들의 상호작용에 의하여 낮은 값을 나타내었다. 접합부의 임계전류 통전성은 반복적인 가압성형 공정과 서냉반응 열처리 공정에 의하여 향상되었다.

• 한국기계가공학회지
• /
• 제20권12호
• /
• pp.113-122
• /
• 2021

Complicated residual stress distributions occur in the vicinity of a deposited region via directed energy deposition (DED) process owing to the rapid heating and cooling cycle of the deposited region and the substrate. The residual stress can cause defects and premature failure in the vicinity of the deposited region. Several heat treatment technologies have been extensively researched and applied on the part deposited by the DED process to relieve the residual stress. The aim of this study was to investigate the residual stress characteristics of a specimen fabricated by DED and a quenching process using thermomechanical analyses. A coupled thermomechanical analysis technique was adopted to predict the residual stress distribution in the vicinity of the deposited region subsequent to the quenching step. The results of the finite element (FE) analyses for the deposition and the cooling measures show that the residual stress in the vicinity of the deposited region significantly increases after the completion of the elastic recovery. The results of the FE analyses for the heating and quenching stages further indicate that the residual stress in the vicinity of the deposited region remarkably increases at the initial stage of quenching. In addition, it is observed that the residual stress for quenching is lesser than that after the elastic recovery, irrespective of the deposited material.

• Macromolecular Research
• /
• 제13권5호
• /
• pp.453-459
• /
• 2005

Natural fiber henequen/unsaturated polyester (UPE) composites were fabricated by means of a compression molding technique using chopped henequen fibers treated at various electron beam (EB) dosages. The interfacial shear strength (IFSS), dynamic mechanical properties, and thermal expansion behavior were investigated through a single fiber microbonding test, fractographic observation, dynamic mechanical analysis, and thermomechanical analysis, respectively. The results indicated that the interfacial and dynamic mechanical properties significantly depended on the level of the EB treatment irradiated onto the henequen fiber surfaces. The effect of EB treatment on the IFSS, storage modulus and fracture surface of the henequen/UPE composites agreed with each other. The results of this study also suggested that the modification of henequen fiber surfaces at 10 kGy EB is the most effective for improving the interfacial properties of the henequen/UPE composites.

• 한국재료학회지
• /
• 제7권11호
• /
• pp.942-950
• /
• 1997

NiAI기 산화물 분산강화(Oxide Dispersion Strengthende:ODS)합금을 기계적 합금화 (Mechanical Alloying: MA)방법으로 제조하였으며, 열간압축방법으로 성형하였다. 연이어 단순항온처리에 의한 정상결정립성장과 특성조건에서의 thermomechanical treatment 에 의한 이차재결정화를 유도하였다. 결정립 조대화된 ODSD MA NiAI의 creep 성질 및 이에 조대화된 미세조직은 creep 성질이 저하된 반면, 이차재결정화된 MA NiAI의 creep성질은 크게 향상되었다. 이 creep 성질의 향상은 이차재결정화의 특성인 급격한 결정립의 조대화, 분산상의 성장억제 및 grain aspect ratio의 증가에 기인한 것으로 사료되었다. 이차재결정화된 ODS MA NiAI의 creep또는 glide controlled dislocation creep임을 제시하지만, 전체 creep속도가 결정립 크기 및 grain aspect ratio의 영향을 크게 받은 것을 볼 때, 결정립계 미끄럼기구가 주 creep 기구와 조합되어 MA NiAI의 전체 creep기구에 영향을 준 것으로 추정할 수 있었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.17-20
• /
• 2000

In order to improve the sheet formability of the ferritic stainless steel, the through-thickness textures of the recrystallized sample was modified by means of a thermomechanical treatment. An annealing process between the cold rolling reductions modified the preferred orientations throughout the thickness, which resulted in the modification of the final cold rolling texture as well as the final recrystallization texture. With the help of the modification of the recrystallization texture by the intermediate annealing, improvement of the sheet formability, i.e. an increase of the Lankford value.

• 연구논문집
• /
• 통권27호
• /
• pp.175-181
• /
• 1997

Superconducting joints between Bi-2223/Ag tapes are fabricated by a press & reaction anneal and a multiple press & anneal. The silver sheath was mechanically or chemically removed from one side of each tape without altering the superconducting core. The exposed superconducting core of the two tapes were brought into contact and pressed so as to form a lap joint. The joined tapes were then subjected to a series of different thermomechanical treatments to achieve optimum heat treatment condition. The result from transport measurements shows that critical current ($I_c$) transmitting through joined area reaches 9A, approximately 60% of the current capacity of the tapes themselves. The critical current through joined area was improved by repeated press and reaction annealing. Measurements of the current-voltage relationship were made with several configuration of the voltage probes to characterize the critical current variation and I-V curve along the joint. Also discussed are microstructural aspects of the superconducting joint.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 춘계학술대회논문집
• /
• pp.114-123
• /
• 1995

Hot workability and microstructural development of 7075Al alloy were studied by hot torsion test. With decling temperature from 440$^{\circ}C$ to 340$^{\circ}C$, and strain rate ranges form 5 ${\times}$10-3/sec to 5 ${\times}$10-1/sec , flow stress and microstructural development were analyzed . The hot resoration mechanism was found to be dynamic recrystalization (DRX) form the analysis of the flow curves and the microstructures. In multistage deformation with decreasing temperature grain refinement was obtained effectively compared to conventional thermomechanical treatment (TMT) process. The strain of the 1st stage deformation at 440$^{\circ}C$ was found to play an important role for the next stage deformation behavior at 380$^{\circ}C$.