• Korean Journal of Remote Sensing
• /
• v.39 no.5_3
• /
• pp.921-932
• /
• 2023

Land cover change due to urban population concentration and urban expansion can cause various environmental problems such as urban heat islands. In particular, New towns are considered an appropriate study site to analyze changes in urban climate due to rapid urbanization in a short period. This study used Landsat satellite imagery to compare and analyze the land cover changes before and after the development of two new towns with different plans, and the resulting changes in surface urban heat island (SUHI) phenomena. Correlation analysis was also conducted between urban structural features that may affect the SUHI intensity. The results of the analysis confirm the rapid change in land cover as new town development progresses and the direct intensification of the SUHI phenomenon. This study confirms the differences in SUHI caused by different urban plans and suggests the need for three-dimensional urban planning to improve the thermal environment.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.4
• /
• pp.276-286
• /
• 2013

The goal of this study was to investigate change of thermal decomposition feature of miscanthus (Miscanthus sacchariflorus) after removal of inorganic constituents using distilled water (D.I-w; 30, 60 and $90^{\circ}C$). The carbon content was increased whereas the oxygen content was decreased with the temperature of D.I-w treatment. Moreover, ash content was slightly decreased from 4.6% of control to 3.2% of $90^{\circ}C$ D.I-w treated sample. Results of total monomeric sugar contents and X-ray diffraction (XRD) analysis showed that structural changes of cellulose/hemicellulose regions did not occurr during D.I-w treatment. Results of inductively coupled plasma emission spectrometer (ICP-ES) showed that miscanthus has the largest amount of inorganic constituents such as potassium (5,644 ppm), phosphorus (3,995 ppm), magnesium (1,403 ppm) and calcium (711 ppm). Thermogravimetric analysis (TGA) confirmed that the yield of char slightly decreased whereas the yield of volatiles increased with increasing D.I-w treatment temperature. In addition, differential thermogravimetric analysis (DTGA) indicated that the maximum decomposition rate ($V_M$) and temperature ($T_M$) corresponding to VM were varied from $0.82%/^{\circ}C$, $360.60^{\circ}C$ of control to $1.17%/^{\circ}C$, $362.62^{\circ}C$ of $90^{\circ}C$-D.I-w treated sample.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.5
• /
• pp.485-492
• /
• 2009

The thermal fatigue crack(TFC) is one of the life-limiting mechanisms at the nuclear power plant operating conditions. In order to evaluate the structural integrity, various non-destructive test methods such as radiographic test, ultrasonic test and eddy current are used in the industrial field. However, these methods have restrictions that defect detection is possible after the crack growth. For this reason, acoustic emission testing(AET) is becoming one of powerful inspection methods, because AET has an advantage that possible to monitor the structure continuously. Generally, every mechanism that affects the integrity of the structure or equipment is a source of acoustic emission signal. Therefore the noise filtering is one of the major works to the almost AET researchers. In this study, acoustic emission signal was collected from the pipes which were in the successive thermal fatigue cycles. The data were filtered based on the results from previous experiments. Through the data analysis, the signal characteristics to distinguish the effective signal from the noises for the TFC were proven as the waveform difference. The experiment results provide preliminary information for the acoustic emission technique to the continuous monitoring of the structure failure detection.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.1
• /
• pp.24-31
• /
• 2021

We report structural, mechanical, and thermal properties of diecast ADC12 aluminum alloys characterized using synchrotron X-ray diffraction (XRD), scanning electron microscopy, energy dispersive X-ray (EDX) analysis, thermal conductivity (λ), Vickers hardness (Hv), and stress-strain measurements. We also studied the effect of post-annealing performed in a vacuum atmosphere on the mechanical properties of diecast ADC12 alloys. EDX and XRD results revealed that Al2Cu and AlCu3 grains are formed, well dispersed in Al base and highly crystalline. Ultimate tensile strength (UTS) of 307.9 ± 9.1 MPa and elongation of 2.98 ± 0.62 % were estimated. λ was 129.3 ± 0.27 W/m·K and Hv was approximately 130. Both values were significantly higher than the reported values. At annealing temperatures ranging from 25 to 200℃, UTS and Hv values remained constant, while as the annealing temperature increased to 500℃, these values gradually decreased. This is because stabilization of the microstructure improves toughness and ductility.

• Korean Journal of Materials Research
• /
• v.29 no.7
• /
• pp.437-442
• /
• 2019

Green $BaSi_2O_2N_2:0.02Eu^{2+}$ phosphor is synthesized through a two-step solid state reaction method. The first firing is for crystallization, and the second firing is for reduction of $Eu^{3+}$ into $Eu^{2+}$ and growth of crystal grains. By thermal analysis, the three-time endothermic reaction is confirmed: pyrolysis reaction of $BaCO_3$ at $900^{\circ}C$ and phase transitions at $1,300^{\circ}C$ and $1,400^{\circ}C$. By structural analysis, it is confirmed that single phase [$BaSi_2O_2N_2$] is obtained with Cmcm space group of orthorhombic structure. After the first firing the morphology is rod-like type and, after the second firing, the morphology becomes round. Our phosphor shows a green emission with a peak position of 495 nm and a peak width of 32 nm due to the $4f^65d^1{\rightarrow}4f^7$ transition of $Eu^{2+}$ ion. An LED package (chip size $5.6{\times}3.0mm$) is fabricated with a mixture of our green $BaSi_2O_2N_2$, and yellow $Y_3Al_5O_{12}$ and red $Sr_2Si_5N_8$ phosphors. The color rendering index (90) is higher than that of the mixture without our green phosphor (82), which indicates that this is an excellent green candidate for white LEDs with a deluxe color rendering index.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.5
• /
• pp.543-551
• /
• 2006

Cold-formed steel studs that are being used as load-bearing members of wall panels for steel houses have a problem with their insulation due to the heat bridging of their web. Some additional thermal insulating materials should be used. To solve this problem, the new-concept hybrid stud, which consists of a galvanized steel sheet (t = 1.0 m - 12.0 m) and a GFRP panel (t = 4.0-6.0 mm), has recently been developed. An investigation on the structural behavior and the strength capacity of this new hybrid stud has been conducted so that it can be used in load-bearing wall panels of residential buildings. This paper describes the axial compression-torsion test results of the hybrid studs under both axial compression and torsion using ATTM. The main factors of the test were the stud length, the magnitude of the initial compressive force, and the loading method of the monotonic or cyclic loading. The torsion was applied increasingly while the initial compression was kept constant to the failure of the hybrid section. The advanced analysis results obtained form the finite element procedure that considered the material properties of the high-strength galvanized steel and the GFRP were compared with the test results for verification.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.83-90
• /
• 1998

Stage transformation characteristics of Li, K and Na-graphite deintercalation compounds (GDICs) were studied under consideration of a deintercalation mechanism of the intercalants between carbon layers. Li-graphite intercalation compounds (GICs) synthesized by a controlling temperatures and pressures have been spontaneously decomposed in the atmosphere. By X-ray differaction analysis the $d_{001}$-values of stage 1 and 2 were identified to be 3.71 and 7.06 $\AA$, respectively. After 6 weeks, the deintercalation reaction of the Li-GICs ceased and only residual compounds could be observed. K-GICs were synthesized by the modified two-bulb method resulting in structural stabilities and stage transitions. By X-ray diffraction analysis the very stable K-graphite residue compounds were observed after 10 weeks. Na-GICs with stage 1 and 2 were synthesized using the high temperature and pressure technique. The temperature dependence of a deintercalation reaction and a thermal stability of Na-GICs were discussed. The structure changes of the Na-GDICs depending on heating rates were identified by X-ray diffraction. According to the deintercalation process, the stage transformations could be attributed to irregular deintercalations of the GDICs with disordered stage.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.1
• /
• pp.79-83
• /
• 2010

The conventional welding technique such as shield metal arc welding has been mostly applied to the piping system of the nuclear power plants. It is well known that this welding technique causes the overheating and welding defects due to the large groove angle of weld. On the other hand, the narrow gap welding(NGW) technique has many merits, for instance, the reduction of welding time, the shrinkage of weld and the small deformation of the weld due to the small groove angle and welding bead width comparing with the conventional welds. These characteristics of NGW affect the deformation behavior and the distribution of welding residual stress of NGW, thus it is believed that the residual stress results obtained from conventional welding procedure may not be applied to structural integrity evaluation of NGW. In this paper, the welding residual stress of NGW was predicted using the nonlinear finite element analysis to simulate the thermal and mechanical effects of the NGW. The present results can be used as the important information to perform the flaw evaluation and to improve the weld procedure of NGW.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.7
• /
• pp.627-633
• /
• 2009

Composite has become one of the most frequently used material for a tube of satellite camera due to its attractive characteristics. However, laminated composites can be weakened by delamination which comes from interlaminar stress. Such failure mode cause structural instability of the camera as well as degradation of optical quality. Therefore composite tube should be robust in delamination. Also, composite tube should have high stiffness, sufficient high natural frequency and small coefficient of thermal expansion. The design procedures presented in this paper are based on design of experiments. The experiments for mechanical analysis are designed by the tables of orthogonal arrays. In order to manipulate the various mechanical properties systematically, multiple-attribute decision making(MADM) is employed. Through analysis of variance and F-test, the critical design variables which have dominant influences on mechanical performance are determined. Finally improved ply angles for composite tube are determined.

• Current Photovoltaic Research
• /
• v.2 no.4
• /
• pp.177-181
• /
• 2014

$Cu_2ZnSn(S_xSe_{1-x})_4$ (CZTSSe) absorber thin films were prepared on Mo coated soda lime glass substrates by sulfo-selenization of sputtered stacked Zn-Sn-Cu precursor thin films. The Zn-Sn-Cu precursor thin films were sulfo-selenized inside a graphite box containing S and Se powder using rapid thermal processing furnace at $540^{\circ}C$ in Ar atmosphere with pre-treatment at $300^{\circ}C$. The effect of different S/Se ratio on the structural, compositional, morphological and electrical properties of the CZTSSe thin films were studied using XRD (X-ray diffraction), XRF (X-ray fluorescence analysis), FE-SEM (field-emission scanning electron microscopy), respectively. The XRD, FE-SEM, XRF results indicated that the properties of sulfo-selenized CZTSSe thin films were strongly related to the S/Se composition ratio. In particular, the CZTS thin film solar cells with S/(S+Se)=0.25 shows best conversion efficiency of 4.6% ($V_{oc}$ : 348 mV, $J_{sc}$ : $26.71mA/cm^2$, FF : 50%, and active area : $0.31cm^2$). Further detailed analysis and discussion for effect of S/Se composition ratio on the properties CZTSSe thin films will be discussed.