• Journal of Advanced Marine Engineering and Technology
• /
• 제10권2호
• /
• pp.156-164
• /
• 1986

In the case of boiling on high temperature wall, vapor film covers fully or parcially the surface. This phenomenon, film boiling or transition boiling, is very important in the surface heat treatment of metal, design of cryogenic heat exchanger and emergency cooling of nuclear reactor. Mainly supposed hydraulic-thermal accidents in nuclear reactor are LCCA (Loss of Coolant Accident) and PCM (Power-Cooling Mismatch). Recently, world-wide studies on reflooding of high temperature rod bundles after the occurrence of the above accidents focus attention on wall temperature history and required time in transient cooling process, wall superheat at rewet point, heat flux-wall superheat relationship beyond the transition boiling region, and two-phase flow state near the surface. It is considered that the further systematical study in this field will be in need in spite of the previous results in ref. (2), (3), (4). The paper is the study about the fast transient cooling process following the wall temperature excursion under the CHF (Critical Heat Flux) condition in a forced convective subcooled boiling system. The test section is a vertically arranged concentric annulus of 800 mm long and 10 mm hydraulic diameter. The inner tube, SUS 304 of 400 mm long, 8 mm I.D, and 7 mm O.D., is heated uniformly by the low voltage AC power. The wall temperature measurements were performed at the axial distance from the inlet of the heating tube, z=390 mm. 6 chromel- alumel thermocouples of 76 .mu.m were press fitted to the inner surface of the heating tube periphery. To investigate the heat transfer characteristics during the fast transient cooling process, the outer surface (fluid side) temperature and the surface heat flux are computed from the measured inner surface temperature history by means of a numerical method for inverse problems of transient heat conduction. Present cooling (boiling) curve is sufficiently compared with the previous results.

• Journal of Magnetics
• /
• 제8권1호
• /
• pp.1-6
• /
• 2003

The new class of $Gd_5(Si_xGe_{1-x})_4$ compounds undergoes a simultaneous magnetic/structural phase transition giving a high level of strain that can be induced either by change in temperature or by application of a magnetic field. Profound changes of structural, magnetic, and electronic changes occur in the $Gd_5(Si_xGe_{1-x})_4$ system lead to extreme behavior of the material such as the giant magnetocaloric effect, colossal magnetostriction, and giant magnetoresistance. These unique material characters can be utilized for various applications including magnetic solid refrigerants, sensors, and actuators.

• 한국전산구조공학회논문집
• /
• 제29권6호
• /
• pp.577-582
• /
• 2016

본 논문에서는 나노입자가 삽입된 고분자 복합재에서 형성되는 계면 상의 정량적인 열탄성 물성을 계산과학적 접근으로 제시하였다. 균질해법이 적용된 유한요소모델과, 미시역학법에 의한 3상 복합재의 열탄성 이론, 그리고 분자동역학 전산모사법이 본 연구에 모두 적용되었고, 이를 유기적으로 연계한 멀티스케일 모델을 수립하였다. 특히, 제시한 유한요소모델과 분자동역학 기반의 나노복합재 모델로부터 각각의 인장하중에 따른 계면의 변형에너지 밀도를 도출, 이를 직접 비교하는 과정이 본 멀티스케일 해석 과정에 포함되었다. 이로써 주어진 온도 조건에 따른 나노입자 주변의 계면 상에 대한 탄성계수와 그 두께를 물리적 엄밀해로써 정량 도출할 수 있다. 이렇게 얻은 고분자 나노복합재의 연속체모델은 다시 미시역학 모델과 연계함으로써, 최종적으로는 광범위한 온도 조건에 의한 재료의 열탄성 거동 및 유리전이거동이 계면 상의 두께와 기계적 물성에 미치는 영향에 대해 분석, 평가하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.287.1-287.1
• /
• 2013

The Isolation of few-layered transition metal dichalcogenides has mainly been performed by mechanical and chemical exfoliation with very low yields. in particular, the two-dimensional layer of molybdenum disulfide (MoS2) has recently attracted much interest due to its direct-gap property and potential application in optoelectronics and energy harvesting. However, the synthetic approach to obtain high-quality and large-area MoS2 atomic thin layers is still rare. In this account, a controlled thermal reductionsulfurization method is used to synthesize large-MoOx thin films are first deposited on Si/SiO2 substrates, which are then sulfurized (under vacuum) at high temperatures. Samples with different thicknesses have been analyzed by Raman spectroscopy and TEM, and their photoluminescence properties have been evaluated. We demonstrated the presence of single-, bi-, and few-layered MoS2 on as-grown samples. It is well known that the electronic structure of these materials is very sensitive to the number of layer, ranging from indirect band gap semiconductor in the bulk phase to direct band gap semiconductor in monolayers. This synthetic approach is simple, scalable, and applicable to other transition metal dichalcogenides. Meanwhile, the obtained MoS2 films are transferable to arbitrary substrates, providing great opportunities to make layered composites by stacking various atomically thin layers.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.50.1-50.1
• /
• 2011

Lead-free ceramics with a composition of 0.55 mol%$K_4CuNb_8O_23-(K_{1-x}Na_x)NbO_3$ (KCN-KNNx) where $0.45{\leq}x{\leq}0.60$ were synthesized by conventional ceramic processing. Results revealed that the addition of Na was effective in changing the microstructure and relative density of KCN-KNNx. Further, the addition of Na resulted in a slight shift of the phase transition temperatures (To-t and Tc) toward low values. A high mechanical quality factor (Qm) of 1850 was found atx=0.54, which might be due to the build-up of an internal bias field (Ei) within KCN. Thermal hysteresis in KNNx was confirmed with an increase in the Na content during the heating and cooling cycles, resulting from structural changes. Thus, KCN-KNNx with x=0.54 exhibits excellent piezoelectric properties with d33 (97 pC/N), kp (36%), and Qm (1850), being promising candidates for application in high-power piezoelectric devices.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1576-1579
• /
• 2005

With varying rapid thermal annealing (RTA) temperature, luminescence properties of $Zn_{0.75}Mg_{0.25}S:Mn$ thin film deposited by RF-magnetron sputtering technique were investigated. In this study, $Zn_{0.75}Mg_{0.25}S:Mn$ thin film phosphor showed more red emission than those of the previous studies when annealed around 600 or $650^{\circ}C$. Although all samples were deposited from identical source composition, a main peak wavelength of photoluminescence spectra of $Zn_{0.75}Mg_{0.25}S:Mn$ shifted toward shorter wavelengths depending upon increase of RTA temperature. The same dependence of wavelength on RTA temperature was also observed in cathodoluminescence as well as electroluminescence measurements. It was revealed that the change of the luminescence properties were originated from structural changes in $Zn_{0.75}Mg_{0.25}S:Mn$ thin film phosphor from cubic to hexagonal phases analyze using conventional X-ray pole figure mapping. The phase transition would be the origin of luminescence property changes with respect to RTA temperature.

• 한국염색가공학회지
• /
• 제22권3호
• /
• pp.181-186
• /
• 2010

A thermoresponsive poly(NIPAM-co-dye) labeled with benzopyran-based D-$\pi$-A type dye was prepared by typical radical copolymerization. It can be also constructed a acid/base-induced molecular switch by modulation of intramolecular charge transfer with protonation/deprotonation. The lower critical solution temperature behavior was investigated by means of UV-vis spectroscopy which allows the measurement of the phase transition from $25^{\circ}C$ to $45^{\circ}C$ in aqueous DMSO solution. The morphology of the internal microstructure of the poly(NIPAM-co-dye) hydrogel was observed by scanning electron microscopy. The reversible switch could be obtained by thermal and acid/base stimuli.

• 한국재료학회지
• /
• 제13권2호
• /
• pp.120-125
• /
• 2003

A low melting borosilicate glass frit was used as an adhesion promoter, which enables $MnWO_4$to be sintered with in a reasonable sintering temperature range ($800∼1000^{\circ}C$). The glass was evaluated for glass transition temperature ($Τ_{g}$ X) and thermal expansion coefficient($\alpha$). Mechanical property (Vickers hardness), grain growth, the comparison of lattice parameter and pore distribution of sintered $MnWO_4$ with the frit were methodically discussed. As sintering temperature increased, a typical liquid phase sintering showed the rapid grain growth and high densification of X$MnWO_4$grain, improvement of hardness (until $920^{\circ}C$) and different pore size distribution. Resistance of sintered $MnWO_4$varied from 450k$\Omega$ to 8.8M$\Omega$ under the measuring humidify ranging from 30 to 90%. Thus, the results will contribute to the application of glass frit containing sensor materials and their future use.

• Elastomers and Composites
• /
• 제41권2호
• /
• pp.108-115
• /
• 2006

비페닐기를 함유하는 새로운 형태의 액정성 폴리우레탄을 신규로 합성한 4,4'-Bis(9-hydroxynonoxy)biphenyl (BP9)와 2,6-tolylene diisocyanate, 2,5-tolylene diisocyanate, 2,4-tolylene diisocyanate, 1,4-phenylene diisocyanate 및 hexamethylene diisocyanate의 중부가 반응에 의해 합성하였다. 단량체 BP9은 스멕틱상을 형성하였으며 1,4-PDI/BP9을 제외한 나머지 폴리우레탄에서는 모두 액정성을 나타내었다. 합성된 단량체와 중합체들의 구조는 적외선분광분석기 및 핵자기공명분석기를 사용하여 확인하였으며, 그들의 열적 상전이 온도 및 안정성들은 시차주사 열량분석기와 편광현미경으로 조사하였다.

• 열처리공학회지
• /
• 제8권1호
• /
• pp.75-83
• /
• 1995

The purpose of this study is to investigate the effect of heat treatments on the martensite transformation and tensile deformation behavior in Ti-Ni-B alloys with various boron concentration. Three types of heat treatment are given to the specimens; i) solution treatment ii) aging iii) thermo-mechanical treatment. In solution treated specimens. R-phase transition which is related to abnormal increase of electrical resistance prior to martensitic transformation has been formed at a boron content of 0.2at % and the $M_s$ temperature has been decreased with the increasing of boron content. However. It has not been affected by aging, while that of thermo-mechanically treated specimens has been remarkably increased in the vicinity of recrystallization temperature. The thermo-mechanically treated specimen has showed a good thermal fatigue characteristics, shape memory effect and superelasticity in comparison with the solution treated specimen.