• Bulletin of the Korean Chemical Society
• /
• 제23권2호
• /
• pp.325-329
• /
• 2002

In this study, the dependency of the behavior of propagating front on the reaction condition in frontal polymerization reaction has been studied. We have used some multifunctional acrylates as a monomer and ammonium persulfate as an initiator for the polymerization reactions. In frontal polymerization, a method of producing polymeric materials via a thermal front that propagates through the unreacted monomer/initiator solution, the behavior of self propagating front shows various dynamic patterns depending on the reaction condition. We have obtained some spin modes of propagating front in the number of 'hot spots' or 'spin heads' by changing the reaction condition. The effect of the reactor tube diameter on the mode of propagating front has also been studied by using some reactor tubes with different size of tube diameter and it has been examined in some detail by adopting an experimental method of two-tubes system.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.487-488
• /
• 2006

In these days, demand of a LCD monitor is remarkably increasing with development of the LCD technology. However, there are thermal problems for improvement of efficiency for the LCD monitor. Thus, this research analyzed thermal problems such as convection and conduction heat transfer characteristics in the LCD monitor using an infrared (IR) camera. Also, the results of the outer side of the front LCD panel using the IR camera have been compared with the results of the inner side of the front panel using T-type thermocouples. The equations have been derived for the temperature distribution of the inner side of the front LCD panel by a multiple regression method including variables for ambient temperature, humidity and temperature differences between the front and back panels of the LCD monitor.

• 한국연소학회지
• /
• 제11권2호
• /
• pp.22-27
• /
• 2006

This experimental study has been mainly motivated to obtain generally applicable design correlation for the front mixing premix combustor. The design concept of the front mixing premix combustor is to minimize thermal $NO_x$ and prompt $NO_x$ formation by maintaining low peak flame temperature, and nearly uniform flame temperature through rapid mixing process near the ignition point. The present experimental results clearly indicate that the front mixing premix combustor yields the $NO_x$ level lower than 43 ppm $NO_x$ emissions and the nearly uniform temperature distribution.

• 한국지리정보학회지
• /
• 제9권2호
• /
• pp.227-238
• /
• 2006

해양에서 수온의 등온선 밀집 정도를 표준지수로 정량화하기 위해 선밀도 지수(line density index: LDI)를 개발하였다. 지수 값의 범위를 0에서 100까지 제한시킨 LDI의 개발과정에 대한 이론적 배경을 기술하였고, line의 총 길이가 해당 면적의 1/10를 넘지 못한다는 적용조건에 대한 타당성 검증도 수행하였다. LDI의 적용 실험을 위해 남해역에서 관측된 NOAA SST 자료를 이용하였다. GIS를 이용하여 SST 레스터 데이터로 부터 $0.1^{\circ}C$ 등온선 벡터 데이터를 선형화하고 단위격자 영역을 폴리곤으로 제작한 후 공간중첩을 통해 LDI를 계산하였다. 단위 영역의 크기가 LDI의 분포에 미치는 영향을 분석하기 위해 두 종류의 격자 크기를 설계하여 LDI의 통계량를 산출하고 정규성 검정을 수행하였다. 분석 결과 격자크기에 따라 LDI의 평균과 정규성 같은 고유특징은 변하지 않으나, 통계량 값의 범위, 분산, 표준편차 등은 변하였는데, 이는 수온전선 구조가 복잡하고 전선폭이 격자 영역보다 훨씬 작을 때 발생하는 문제임이 확인되었다. 또한, LDI와 수온 차(${\Delta}T^{\circ}C$) 와의 관계성을 분석하고 수온전선역의 수온 수평경도(${\Delta}T^{\circ}C/km$)를 선형회귀모델로부터 계산하여 기존 연구자들의 제시한 수온전선역에서의 수온 수평경도 값과도 비교하였다. 본 연구를 통해 새롭게 개발된 LDI가 지니는 의미는 해양환경에서 시 공간적인 변화에 따른 수온전선 형성 지역을 절대적인 지수치로 비교 가능함은 물론, 수온전선과 해양환경 또는 해양생물과의 관계를 정량적으로 분석할 수 있는 기반을 제시했다는 점이다.

• 한국음향학회지
• /
• 제7권4호
• /
• pp.110-116
• /
• 1988

한국 남서 해안에 겨울철 발생하는 수온전선으로 매우 특이한 음향매체가 존재한다. 이러한 조건하에서의 음파방정식은 변수분리가 용이하고 그 해 역시 간단하며 이는 이미 잘 알려진 수학적인 해이다. 수평 성분의 방정식 해를 구하기 위하여 WKB 방법 대신 mode 방법을 사용하였으며 구한 해의 특성은 수온전선이 존재함으로 야기된 수중음속의 수평변화로 인한 영향은 주파수에 따라 그 크기가 달라진다. 이를 설명하기 위해 ray tracing 을 이용, 그 물리적인 의미를 부여하였다.

• 대한기계학회논문집
• /
• 제17권2호
• /
• pp.438-444
• /
• 1993

The circuit board of an electronic equipment were simulated with a vertical channel which had thermal blocks protruded from one of the channel walls. A rought front plate was made of a circuit board attached with short wires to simulate the back side of a printed circuit board. Natural convection experiments were carried out to study the effects of channel space and rough front plate and to find the suitable characteristic value after the fourth row. The effect of a rough front plate was negligble. There were negligible effects of the channel space on the first and second heaters. Heat transfer coefficients after the third row decreased as the channel space decreased. Heat transfer coefficients were almost constant for larger than 20 mm channel space. A characteristic length was suggested to non-dimensionalize Nu and Ra numbers in a vertical channel with protruded heaters. A correlation was obtained using the new characteristic lengths.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.122.1-122.1
• /
• 2011

Phosphorus is known to pile-up at the silicon surface when it is thermally oxidized. A thin layer, about 40nm thick from the silicon surface, is created containing more phosphorus than the bulk of the emitter. This layer has a gaussian profile with the peak at the surface of the silicon. In this study the pile-up effect was studied if this layer can act as a front surface field for solar cells. The effect was also tested if its high dose of phosphorus at the silicon surface can lower the contact resistance with the front metal contact. P-type wafers were first doped with phosphorus to create an n-type emitter. The doping was done using either a furnace or ion implantation. The wafers were then oxidized using dry thermal oxidation. The effect of the pile-up as a front surface field was checked by measuring the minority carrier lifetime using a QSSPC. The contact resistance of the wafers were also measured to see if the pile-up effect can lower the series resistance.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.237-242
• /
• 2001

This paper presents the thermal characteristics analysis of a high-speed HMC spindle system with angular contact ball bearings, built-in motor, oil-jet lubrication method, oil jacket cooling method, and so on. The spindle system is composed of the main spindle and sub-spindle which are mechanically connected by a flexible coupling. The spindles are supported by two front and rear bearings, and the built-in motor is located between the front and rear bearings of the sub-spindle. The thermal analysis model of spindle system is constructed by the finite element method, and the thermal characteristics in the design stage are estimated based on temperature distribution, heat flow and thermal deformation under the various testing conditions related to material of bearing ball, spindle speed and coolant temperature.

• 한국공작기계학회논문집
• /
• 제13권1호
• /
• pp.69-75
• /
• 2004

This paper presents the thermal characteristics analysis of a high-speed motor-separated spindle system consisted of angular contact ball bearings and built-in motor with oil-jet lubrication. The spindle system is composed of the main spindle and sub-spindle which are mechanically connected by a flexible coupling. The spindles are supported by two front and rear bearings, and the built-in motor is located between the front and rear bearings of the sub-spindle. The thermal analysis model of spindle system is constructed by the finite element method, and the thermal characteristics in the design stage are estimated based on temperature distribution and heat flow under the various testing conditions related to material of bearing ball, spindle speed and coolant temperature.

• Nuclear Engineering and Technology
• /
• 제54권3호
• /
• pp.1085-1097
• /
• 2022

A printed circuit steam generator (PCSG) is being considered as the component for pressurized water reactor (PWR) type small modular reactor (SMR) that can further reduce the physical size of the system. Since a steam generator in many PWR-type SMR generates superheated steam, it is expected that dryout front oscillation can potentially cause thermal fatigue failure due to cyclic thermal stresses induced by the transition in boiling regimes between convective evaporation and film boiling. To investigate the fatigue issue of a PCSG, a reference PCSG is designed in this study first using an in-house PCSG design tool. For the stress analysis, a finite element method analysis model is developed to obtain the temperature and stress fields of the designed PCSG. Fatigue estimation is performed based on ASME Boiler and pressure vessel code to identify the major parameters influencing the fatigue life time originating from the dryout front oscillation. As a result of this study, the limit on the temperature difference between the hot side and cold side fluids is obtained. Moreover, it is found that the heat transfer coefficient of convective evaporation and film boiling regimes play an essential role in the fatigue life cycle as well as the temperature difference.