• Nuclear Engineering and Technology
• /
• v.53 no.3
• /
• pp.804-811
• /
• 2021

The T-junction exists widely in industrial engineering, especially in nuclear power plants, which plays an important part in nuclear power reactor thermal-hydraulics. However, the existing prediction models of the liquid entrainment are mainly based on the small branches or small breaks while there are a few researches for large branches (d/D > 0.2). Referring to the classical models about the onset of liquid entrainment of the T-junction, most of previous models regard liquid as ideal working fluid and ignore surface tension. This paper aims to study the effect of surface tension on the liquid entrainment, and develops an improved model based on the reasonable assumption. The establishment of new model employs the methods of force analysis, dimensional analysis. Besides, the dimensionless Weber number is adopted innovatively into the model to show the effect of surface tension. What is more, in order to validate the new model, three kinds of working fluids with different surface tensions are creatively adopted in the experiments: water, silicone oil and ethyl alcohol. The final results show that surface tension has a nonnegligible effect on the onset of liquid entrainment in large branch T-junction. The new model is well matched with the experimental data.

• Steel and Composite Structures
• /
• v.39 no.4
• /
• pp.453-469
• /
• 2021

The cracking at the transverse diaphragm cutout is one of the most severe fatigue failures threatening orthotropic steel decks (OSDs), whose mechanisms and crack treatment techniques have not been fully studied. In this paper, full-scale experiments were first performed to investigate the fatigue performance of polished cutouts involving the effect of an artificial geometrical defect. Following this, comparative experimental testing for defective cutouts strengthened with carbon fiber-reinforced polymer (CFRP) was carried out. Numerical finite element analysis was also performed to verify and explain the experimental observations. Results show that the combinative effect of the wheel load and thermal residual stress constitutes the external driving force for the fatigue cracking of the cutout. Initial geometrical defects are confirmed as a critical factor affecting the fatigue cracking. The principal stress 6 mm away from the free edge of the cutout can be adopted as the nominal stress of the cutout during fatigue evaluation, and the fatigue resistance of polished cutouts is higher than Grade A in AASHTO specification. The bonded CFRP system is highly effective in extending the fatigue life of the defective cutouts. The present study provides some new insights into the fatigue evaluation and repair of OSDs.

• Earthquakes and Structures
• /
• v.20 no.2
• /
• pp.201-213
• /
• 2021

Contrast to the conventional jointed bridge design, integral abutment bridges (IABs) offer some marked advantages like reduced maintenance and enhanced service life of the structure due to elimination of joints in the deck and monolithic construction practices. However, the force transfer mechanism during seismic and thermal movements is a topic of interest owing to rigid connection between superstructure and substructure (piers and abutments). This study attempts to model an existing IAB by including the abutment backfill interaction and soil-foundation interaction effects using Winkler foundation assumption to determine its seismic response. Keeping in view the significance of abutment behavior in an IAB, the probability of damage to the abutment is evaluated using fragility function. Incremental Dynamic Analysis (IDA) approach is used in this regard, wherein, nonlinear time history analyses are conducted on the numerical model using a selected suite of ground motions with increasing intensities until damage to abutment. It is concluded from the fragility analysis results that for a MCE level earthquake in the location of integral bridge, the probability of complete damage to the abutment is minimal.

• Geomechanics and Engineering
• /
• v.24 no.6
• /
• pp.531-543
• /
• 2021

Freezing and thawing of pore water within backfill can affect the stability of retaining wall as the phase change of pore water causes changes in the mechanical characteristics of backfill material. In this study, the effects of freezing and thawing on the mechanical performance of retaining wall with granular backfill were investigated for various temperature and groundwater level (GWL) conditions. The thermal and mechanical finite element analyses were performed by assigning the coefficient of lateral earth pressure according to phase change of soil for at-rest, active and passive stress states. For the at-rest condition, the mobilized lateral stress and overturning moment changed markedly during freezing and thawing. Active-state displacements for the thawed condition were larger than for the unfrozen condition whereas the effect of freezing and thawing was small for the passive condition. GWL affected significantly the lateral force and overturning moment (Mo) acting on the wall during freezing and thawing, indicating that the reduction of safety margin and wall collapse due to freezing and thawing can occur in sudden, unexpected patterns. The beneficial effect of an insulation layer between the retaining wall and the backfill in reducing the heat conduction from the wall face was also investigated and presented.

• Nuclear Engineering and Technology
• /
• v.54 no.8
• /
• pp.2960-2973
• /
• 2022

Since Fukushima nuclear power plant (NPP) accident in 2011, the importance of research on various severe accident phenomena has been emphasized. Particularly, detailed analysis of combustion risk is necessary following the containment damage caused by combustion in the Fukushima accident. Many studies have been conducted to evaluate the risk of local hydrogen concentration increases and flame propagation using computational code. In particular, the potential for combustion by local hydrogen concentration in specific areas within the containment has been emphasized. In this study, the process of flame propagation generated inside a reactor core to containment during a loss of coolant accident (LOCA) was analyzed using MELCOR 2.1 code. Later in the LOCA scenario, it was expected that hydrogen combustion occurred inside the reactor core owing to oxygen inflow through the cold leg break area. The main driving force of the oxygen intrusion is the elevated containment pressure due to the molten corium-concrete interaction. The thermal and mechanical loads caused by the flame threaten the integrity of the containment. Additionally, the containment spray system effectiveness in this situation was evaluated because changes in pressure gradient and concentrations of flammable gases greatly affect the overall behavior of ignition and subsequent containment integrity.

• Textile Coloration and Finishing
• /
• v.34 no.3
• /
• pp.173-184
• /
• 2022

In this study, the TPU film was laminated on an aramid fabric or circular knits in order to implement an air cushion material that can respond to high impact forces in case of a fall and is easy to expand. To increase the bonding strength between the fabric layer and the film layer, a primer layer was formed in two ways: one for thermally bonding and laminating PET film and two for coating and aging hot melt type PUR adhesive. The tensile strength of the aramid air cushion was 2.5 times higher than that of the circular knits, but the tensile elongation of the aramid air cushion was very low compared to that of the circular knits. The tear strength of the aramid air cushion was about twice or more superior to that of the circular knits, the primer treatment method was good at A, and the peel strength was excellent at method A. The aramid air cushion was the lightest in weight. Summarizing the above results, it was best to combine the air cushion material with aramid woven fabric and primer treatment method A to cope with the high impact force applied when falling.

• Journal of The Korean Astronomical Society
• /
• v.55 no.6
• /
• pp.215-220
• /
• 2022

To seek an atmospheric heating mechanism operating on the Sun we investigated a heating source generated by a downflow, both of which may arise in a magnetic loop dynamically formed on the Sun via flux emergence. Since an observation shows that the illumination of evolving magnetic loops under the dynamic formation occurs sporadically and intermittently, we performed a magnetohydrodynamic simulation of flux emergence to obtain a high-cadence simulated data, where temperature enhancement was identified at the footpoint of an evolving magnetic loop. Unlike a rigid magnetic loop with a confined flow in it, the evolving loop in a low plasma β atmosphere is subjected to local compression by the magnetic field surrounding the loop, which drives a strong supersonic downflow generating an effective footpoint heating source in it. This may introduce an energy conversion system to the magnetized atmosphere of the Sun, in which the free magnetic energy causing the compression via Lorentz force is converted to the flow energy, and eventually reduced to the thermal energy. Dynamic and thermodynamic states involved in the system are explained.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.11
• /
• pp.115-120
• /
• 2021

In this study, cigarettes, which are an essential element in the production of tobacco, are generally not cylindrical. The main materials used for cigarettes are generally hemp and pulp. For the production of cylindrical cigarettes, the cigarettes or cylinders are mounted via gluing. This adhesive is a vinyl acetate emulsion, a high-temperature melt adhesive, and is adhered in a cylindrical shape immediately after being linearly applied to the inner surface of the paper roll or a local part. These adhesives are greatly affected by the atmospheric temperature of the manufacturing space in summer and winter. In the summer, even if the adhesive is temporarily adhered, the coagulation time of the adhesive is long, and problems such as deterioration of the adhesive state occur. in the winter, there is a problem that the temperature of the manufacturing space is low and the adhesive force of the adhesive is poor, resulting in defective adhesive products. In order to solve these problems, another heat transfer device is utilized to cure the remaining adhesive to ensure higher adhesiveness.

• Membrane Journal
• /
• v.32 no.6
• /
• pp.383-389
• /
• 2022

Membrane separation process is an important technique utilized for various applications. This separation process proceeds due to a driving force such as concentration gradient, pressure or electrical potential gradient etc. Pervaporation is one of the separation process based on solution-diffusion mechanism. The pressure of the permeate side is reduced by creating vacuum and separation is driven due to pressure difference. Purity of the fuel or chemical like ethanol or isopropyl alcohol are improved by dehydration process through porous zeolite membrane. These membranes have high thermal, chemical, mechanical stability. This review is classified mainly into two different sections: Ethanol and bio-oil dehydration by zeolite membrane.

• Advances in concrete construction
• /
• v.15 no.1
• /
• pp.1-10
• /
• 2023

Concrete is one of the most widely used structure materials. Concrete is like the motor of the construction industry. The remarkable feature of this Concrete is its cheapness and low energy consumption. Concrete alone does not show resistance against any force but only against compressive forces. Therefore, steel rebar product is used as a reinforcement and increase the strength of Concrete. It can be done by putting rebar in Concrete in different ways. Rebar rusting is one of the crucial symptoms that cause swift destruction in reinforced structures-factors such as moisture in concrete increase the steel corrosion rate. In most cases, it is difficult to compensate for the damage caused by the corrosion of base metals, so preventing corrosion will be much more cost-effective. Coatings made with nanotechnology can protect Concrete against external degradation factors to prevent water and humidity from penetrating the Concrete and prevent rusting and corrosion of the rebar inside. It prevents water penetration and contamination into the Concrete and increases the Concrete's quality and structural efficiency. In this research, silica and titanium dioxide nanoparticle coatings have been used due to their suitable electrical and thermal properties, resistance to oxidation, corrosion, and wear to prevent the corrosion of rebars in Concrete. The results of this method show that these nanoparticles significantly improve the corrosion resistance of rebars.