• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.898-901
• /
• 2000

It is known that Si3N4 ceramic insert has less hardness than Al2O3 ceramic insert. But Si3N4 ceramic insert has not only high toughness and strength but also low thermal expansion coefficient, which makes it has longer tool life under thermal stress condition. In this study, commercial Si3N4 ceramic insert and home-made SiC-Si3N4 ceramic insert which has different sintering time and chemical composition is tested under various cutting conditions. The experimental result is compared in terms of tool life and cutting force. Generally, As the cutting speed and the feed rate increased, the cutting force and the flank wear increased too. The performance of SiC-Si3N4 ceramic insert shows the possibility to be a new ceramic tool.

• International Journal of Precision Engineering and Manufacturing
• /
• 제3권1호
• /
• pp.76-82
• /
• 2002

This paper presents an experimental study of the effect of cutting tool materials on surface quality when turning hardened steels. Machining tests on a lathe are performed using polycrystalline cubic boron nitride (PCBN) and ceramic tools at various cutting conditions without coolant. From the experiments, it is observed that the radial force is the largest force component regardless the type of tool used. The specific cutting energy for the hard turning is estimated to be considerably smaller than the specific grinding energy. It is also found that cutting force and surface roughness with the PCBN tools are higher and better than those with the ceramic tools under the same cutting condition. It is due that the PCBN tools transfer the generated heat more effectively than the ceramic tools due to their higher thermal conductivity. The optimal cutting conditions for the best surface quality are selected by using an orthogonal array concept.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.335-340
• /
• 2003

This paper presents contact behavior of a perfluoroelastomer bonded door seal by a non-linear finite element method using the mechanical and thermal analysis. The shape effects are investigated for sealing performance of bonded door seal. Also maximum stress, temperature distribution and contact force are investigated. A bonded door seal was modeled three shape. The highest contact force occurs at model III(sunflower shape). The maximum stress of model III is lower than that of the others. The calculated FEM results show that the model III has excellent performance compared with other seal models.

• 한국결정성장학회지
• /
• 제9권5호
• /
• pp.454-458
• /
• 1999

Hydrodynamic Thermal Capilary Model developed previously has been modified to study the transport phenomena in the Czochralski process. Our analysis is focused on the heat transfer in the system, convection in the melt phase, and the meniscus and interface shape. Four major forces drive melt flow in the crucible, which include thermal buoyancy force in the melt, thermocapillary force along the curved meniscus, crucible rotation and crystal rotation. Individual flow mechanism due to each driving force has been examined to determine its interaction with the meniscus and interface shape. A nominal 4-inch-diameter silicon crystal growth process is chosen as a subject for analysis. Heater temperature profile for constant diameter crystal is also present as a function of crystal height or fraction solidified.

• 조명전기설비학회논문지
• /
• 제21권6호
• /
• pp.85-93
• /
• 2007

본 논문에서는 철심형 영구자석 선형동기전동기(PMLSM, Steel-Cored Permanent Magnet Linear Synchronous Motor)에서 운전 특성을 고려한 설계 특성 및 전략 등에 대한 내용을 다룬다. 특히 반송장치의 운송궤적에서 요구하는 동적특성과 전동기의 동적용량(Dynamic Capability)을 고려한 동적제약조건(Dynamic Constraints) 규정을 통하여, 짧은 변위의 급가감속 왕복운전을 위한 철심형 PMLSM의 최적설계 전략을 살펴본다. 이와 더불어 동특성이 두드러진 PMLSM의 설계특성으로 열적인 특성, 디텐트력 해석 및 저감, 그리고 자계의 포화특성에 대하여 추가 고찰한다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1115-1117
• /
• 2005

This paper describes the three dimension model and simulation results of a thermal actuator based on polyMUMPs process, known as thermal multimorph actuator. The device has potential application in micro-transducers such as atomic force microscope (AFM) tip and scanning tunneling microscope (STM) tip. This device made of a multi-layer materials stack together with consisted of polysilicon, $SiO_2$ and gold. A mask layout design, three dimension model and simulation results are reported and discussed.

• Journal of Welding and Joining
• /
• 제19권6호
• /
• pp.658-663
• /
• 2001

Residual stress caused in the weldments with high restraint force are often during welding observed in the weldments of large size nozzles or radial tanks. The reason is that quantitative analysis about thermal stresses during welding is lack for this weldments. To verify FEM theory, the temperature was measured with thermocouple in a real time in this paper. Also analysis of the thermal stress for welding condition is performed by ABAQUS program package on various welding condition in STS butt welding.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.969-974
• /
• 2002

Thermal characteristics according to the cooling methods are studied for the three type spindles with high frequency motor. For the analysis, three dimensional mode]s are built considering heat transfer characteristics such as natural and force convection coefficients. Unsteady-state temperature distributions and thermal deformations according to the cooling conditions are analyzed by using the finite element method.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.101-106
• /
• 2005

During braking at a train, thermal energy is generated due to the frictions between disk and lining and wheel and shoe. In general, the braking transfers the kinetic energy into thermal energy. Therefore. the frictional characteristics are varied according to the braking force, the thermal resistance, and the thermostable, etc. Using a Dynamo testing we have studied the frictional characteristics and the thermal distribution to investigate a stable speed and to improve the testing method through comparing and analysing in the measurement or the thermocouple temperature and infrared camera.

• Tribology and Lubricants
• /
• 제22권4호
• /
• pp.182-189
• /
• 2006

In this paper, the adhesion characteristics between a fused silica without or with an anti-sticking layer and a thermoplastic polymer film used in thermal NIL were investigated experimentally in order to identify the release performance of the anti-sticking layer. The anti-sticking layers were derived from fluoroalkylsilanes, (1H, 1 H, 2H, 2H-perfluorooctyl)trichlorosilane ($F_{13}-OTS$) and (3, 3, 3-trifluoropropyl)trichlorosilane (FPTS), and coated on the silica surface in vapor phase. The commercial polymers, mr-I 7020 and 8020 (micro resist technology, GmbH), for thermal NIL were spin-coated on Si substrate with a rectangular island which was fabricated by conventional microfabrication process to achieve small contact area and easy alignment of flat contact sur- faces. Experimental conditions were similar to the process conditions of thermal NIL. When the polymer film on the island was separated from the silica surface after imprint process, the adhesion force between the silica surface and the polymer film was measured and the surfaces of the silica and the polymer film after the separation were observed. As a result, the anti-sticking layers remarkably reduced the adhesion force and the surface damage of polymer film and the chain length of silane affects the adhesion characteristics. The anti-sticking layers derived from FPTS and $F_{13}-OTS$ reduced the adhesion force per unit area to 38% and 16% of the silica sur-faces without an anti-sticking layer, respectively. The anti-sticking layer derived from $F_{13}-OTS$ was more effective to reduce the adhesion, while both of the anti-sticking layers prevented the surface damages of the polymer film. Finally, it is also found that the adhesion characteristics of mr-I 7020 and mr-I 8020 polymer films were similar with each other.