• Journal of the Korean Solar Energy Society
• /
• v.36 no.2
• /
• pp.1-7
• /
• 2016

This study was experimentally performed to analyze the growth characteristics of a plant(wax tree or privet) using the surface temperature measured from thermal images captured using a thermal camera with water and cider. To do that, this study measured every each 12 hours the surface temperature and the stem temperature of leaves attached to the plant sample until the plants wilt on summer season in the laboratory room. From the experimental results, this study revealed that the temperature of front and back of the leaves is a little different due to the pore. The mean surface temperature of a leaf in cider is $0.52^{\circ}C$ higher than that of a leaf in water. The phenomena that the leaves of plants fall could be also demonstrated using the surface temperature. Before a leaf is falling from the tree, the temperature of the stem is lowered about $2^{\circ}C$ than those of other parts in a leaf. This result can be validated from previous result performed in University of Wisconsin.

• Progress in Superconductivity and Cryogenics
• /
• v.18 no.4
• /
• pp.25-29
• /
• 2016

The high temperature superconducting (HTS) contra-rotating propulsion (CRP) systems comprise two coaxial propellers sited on behind the other and rotate in opposite directions. They have the hydrodynamic advantage of recovering the slipstream rotational energy which would otherwise be lost to a conventional single-screw system. However, the cooling systems used for HTS CRP system need a high cooling power enough to maintain a low temperature of 2G HTS material operating at liquid neon (LNe) temperature (24.5 - 27 K). In this paper, a single thermo-syphon cooling approach using a Gifford-McMahon (G-M) cryo-cooler is presented. First, an optimal thermal design of a 1.5 MW HTS motor was conducted varying to different types of commercial 2G HTS tapes. Then, a mono-cryogenic cooling system for an integration of two 1.5 MW HTS motors will be designed and analyzed. Finally, the 3D finite element analysis (FEA) simulation of thermal characteristics was also performed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.9 s.180
• /
• pp.2183-2190
• /
• 2000

A thermal aging is observed in a primary reactor cooling system(RCS) made of a casting stainless steel when the RCS is exposed for long period at the reactor operating temperature, 290~3300C An investigation of effects of thermal aging on a low cycle fatigue characteristics included a stress variations caused by a reactor operation and trip, is required. The purpose of the present investigation is to find an effect of a thermal aging of the CF8M on a low cycle fatigue life. The specimen of CF8M are prepared by an artificially accelerated aging technique holding 300 and 1800hr at 4300C respectively. The low cycle fatigue tests for the virgin and two aged specimens are performed at the room temperature for various strain amplitudes($\varepsilon$ta), 0.3, 0.5, 0.8, 1.0, 1.2 and 1.5% strain. Through the experiment, it is found that the fatigue life is rapidly reduced with an creasing of the aging time. The experimental fatigue life estimation formulas between the virgin and two aged specimen are obtained and are proposed to a analysis purpose.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.9 no.1
• /
• pp.17-27
• /
• 1985

In order to investigate the warmth retaining properties of fabrics some characteristics such as thickness. porosity, packing density, thermal conductivity, moisture regain and air permeability were measured and experimental results were analysed statistically to relate the warmth retaining properties with those characteristics. From the analysis, the following results were obtained. 1. When the warmth retaining properties of fabrics (Y) are dependent variable and thickness ($x_1$), porosity ($x_2$), packing density ($x_3$), thermal conductivity ($x_4$), moisture regain ($x_5$) and air permeability ($x_6$) are independent variables, the regression equation of warmth retaining properties can be represented as follows. 1) Y= 1.6005+46.817$x_1$, (R=0.9487) 2)Y=-1.4187+26.5072$x_1$+0.2055$x_2$(R=0.9704) 3) Y= -3.6908+17.4482$x_1$+0.1782$x_2$+28.3243$x_3$ (R=0.9756) 4) Y=0.9202+16.9553$x_1$+0. 1167$x_2$+30.3577$x_3$+1.8884$x_4$ (R=0.9792) 5) Y=0.9353+17.2266$x_1$+0.1177$x_2$+28.9821$x_3$-1.8302$x_4$+0.0151$x_5$ (R=0.9792) 6) Y=0.7583+17.2343$x_1$+0.1196$x_2$+28.8830$x_3$-1.8336$x_4$+0.0187$x_5$0.0004$x_5$ (R=0.9792) 2. The warmth retaining properties of fabrics are merely affected by adding thermal conductivity, moisture regain and multiple regression equation which contains thickness, porosity and packing density as variables. Therefore the multiple regression which contains thickness, porosity and packing density as variables Y=-3.6908+17.4482$x_1$+0.1782$x_2$+28.3243$x_3$ is highly practical.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.194-200
• /
• 2020

Perylene bisimide derivatives are developed for red organic phosphor because of their advantages, such as excellent luminous efficiency and high thermal stability. Despite these advantages, they have poor solubility characteristics in organic solvents and short emission wavelength as red organic phosphor for hybrid light-emitting diodes (LEDs). In this study, we prepared terrylene bisimide using a coupling reaction and swallow-tail imide group, which has excellent solubility. The structures and properties of swallow-tail terrylene bisimide (9C) were analyzed using ¹H-nuclear magnetic resonance (¹H-NMR), Fourier-transform infrared (FT-IR), UV/Vis spectroscopy, and thermal gravimetric analysis (TGA). The maximum absorption wavelength of (9C) in the UV/Vis spectrum was 647 nm, and the maximum emission wavelength was 676 nm. In the TGA, (9C) demonstrated good thermal stability with less than 5 wt% weight loss up to 415℃. In the solubility test, (9C) has a good solubility of more than 5 wt% in chloroform and dichloromethane. When the compounds (9C) were mixed with PMMA (polymethly methacrylate), the films showed peaks at 680 nm in the PL spectra. The results verify the suitability of (9C) as a red organic phosphor for hybrid LEDs.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1295-1297
• /
• 1993

Properties of oxynitride films oxidized by $N_2O$ gas after thermal oxidation and $N_2O$ oxide films directly oxidized using $N_2O$ gas on the bare silicon wafer have been studied. Through the AES analysis, Nitrogen pile-up at the interface of Si/oxynitride and Si/$N_2O$ oxide has observed. Also, it could be presumed that there are differences in the mechanism of the growth of film by observing film growth. $N_2O$ oxide and oxynitride films have the self-limited characteristics. Therefore, it will be possible to obtain ultra-thin films. Nitrogen pile-up at the interfaces Si/oxynitride and Si/$N_2O$ oxide strengthens film structure and improves dielectric reliability. Although fixed charge densities and interface trap densities of $N_2O$ oxide and oxynitride films has somewhat higher than those of thermal $SiO_2,\;N_2O$ oxide and oxynitride films showed improved I-V characteristics and constant current stress.

• Nuclear Engineering and Technology
• /
• v.26 no.2
• /
• pp.225-236
• /
• 1994

The sudden discharge of the loop seal water, which is present upstream of the SEBIM POSRV, creates large momentum and inertia forces on the downstream of the discharge piping system. This study provides the procedures and results of analysis of the thermal-hydraulic transient in the SEBIM POSRV discharge piping during the valve opening. The analysis is peformed by RELAP5/MOD3. The appropriate modeling of the discharge piping system, SEBIM POSRV opening characteristics, and loop seal water discharge for the RELAP5/MOD3 analysis is suggested. Also performed is the sensitivity study for the selection of proper options for the junction and volume control. flags. The analysis results demonstrate the adequacy of the RELAP5/HOD3 for the thermal-hydraulic transient analysis of the loop seal water discharge of the SEBIM POSRV discharge piping system. From the sensitivity analysis results, it is shown that the smooth area change option with reasonable geometric pressure drop distribution, non-equilibrium option, and proper time step should be selected for loop seal water discharge analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.24-31
• /
• 2004

A cylindrical constant volume combustion bomb is used to investigate the combustion characteristics and to analyzer the heat quantity of inhomogeneous charge methane-air mixture. To analyze the heat quantity, some definitions including the CHR ratio, the UHC ratio and the HL ratio are needed and are calculated. It is shown that the effect of stratification is not significant in case of the overall excess air ratio of 1.1, mainly due to the higher heat loss and lower thermal efficiency compared to those of homogeneous condition. In the case of the overall excess air ratio of 1.4, as the initial charge pressure decreases, the CHR ratio has been decreased while the HL ratio has been increased, Generally, as the initial charge pressure increases, the amount of injection mixture has been decreased and has resulted in lower mean velocity and turbulence intensity for injection mixture. Also, the injected mixture is too rich to result in mixing deficiency in combustion chamber. From these results, it could be possible to acquire the improvement of thermal efficiency and the reduction of heat loss simultaneously through the 2-stage injection in CNG direct injection engine.

• The Journal of the Acoustical Society of Korea
• /
• v.13 no.6
• /
• pp.24-30
• /
• 1994

In this paper, the system for detection of photoacoustic signal has been constructed by using CW $CO_{2}$ laser for an analysis of the photoacoustic signal In metals and aluminum carbon steel, brass have been used as sample. The photoacoustic signals of several nano amperes have been detected in each sample with varying modulation frequency of laser, time constant of lock-in amplifier, thickness of sample. The characteristics of photoacoustic signal has been analysed in term of phase angle by using signal processing technique. Results indicate that the photoacoustic signal can be stabilized by adjustment of time constant of lock-in amplifier, that the signal amplitude is proportional to the ratio of thermal expansion coefficient to thermal capacity of metal, and that the signal amplitude decreases exponentially with sample thickness as well as with modulation frequency.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.9
• /
• pp.772-779
• /
• 2007

In this paper, thermo-flow characteristics of an outer-rotor type BLDC motor are numerically analyzed using three-dimensional turbulence modeling. On the rotor of the BLDC motor, cooling blades and cooling holes are existed for the enhanced cooling performances. Rotating the blades and holes generates axial air flow streaming into inner rotor side and passing through stator slots, which cools down stator by forced convection. Operating tests are performed and the numerical temperature fields are found to be in good agreement with experimental results. A new design of the BLDC motor has also been developed and major design parameters such as the arrangement of cooling holes, the area of cooling holes and cooling blades, and the cooling blade angle, are analyzed for the enhanced convective heat transfer rate. It is found that the convective heat transfer rate of the new BLDC motor model is increased by about 8.1%, compared to that of the reference model.