• 한국지반공학회논문집
• /
• 제36권8호
• /
• pp.49-60
• /
• 2020

동상민감성 시료의 동상 거동을 평가하기 위해 완전히 결합된 열-수리-역학 연계해석을 수행하였다. 이를 위한 구성모델은 질량보존방정식, 에너지보존방정식, 힘평형방정식을 기반으로 유도되었다. 구성모델을 통해 간극수의 상변화, 간극수 유동 및 수반되는 기계적 변형 등 1차원 동결에 대한 다양한 물리적 현상을 정량적으로 고려할 수 있었다. 한편, 시료의 동상발생량 및 동상속도에 미치는 영향 인자들을 조사하기 위해 민감도 분석 연구가 수행되었다. 민감도 분석 결과에 따르면, 시료의 초기 간극비는 종속변수인 동상발생량과 동상속도에 독립적으로 큰 영향을 미치는 반면 흙 입자 열전도도 및 온도구배는 독립적으로 미치는 영향보다 두 변수 간 상호 작용을 통해 더 큰 영향을 미침을 확인하였다. 본 연구에서 고려된 인자들은 모두 동상발생량과 동상속도에 영향을 미치는 주요 인자이며, 표본시료의 동상민감성 여부를 결정하는 데에 활용될 수 있을 것이다.

• 센서학회지
• /
• 제14권1호
• /
• pp.52-55
• /
• 2005

Ni oxide thin films with thermal sensitivity superior to Pt and Ni thin films were formed through annealing treatment after Ni thin films were deposited by a r.f. magnetron sputtering method. Resistivity values of Ni oxide thin films were in the range of $10.5{\mu}{\Omega}cm$ to $2.84{\times}10^{4}{\mu}{\Omega}cm$ according to the degree of Ni oxidation. Also temperature coefficient of resistance(TCR) values of Ni oxide thin films depended on the degree of Ni oxidation from 2,188 ppm/$^{\circ}C$ to 5,630 ppm/$^{\circ}C$ in the temperature range of $0{\sim}150^{\circ}C$. Because of the high linear TCR and resistivity characteristics, Ni oxide thin films exhibit much higher sensitivity to flow and temperature changes than pure Ni thin films and Pt thin films.

• 대한토목학회논문집
• /
• 제26권4A호
• /
• pp.719-726
• /
• 2006

전세계적으로 널리 사용되고 있는 장대레일 궤도는 유지 보수 비용을 절감시키고, 궤도구성요소들의 수명이 길어진다는 장점을 가지고 있다. 그러나, 혹서기에 레일의 높은 온도 상승으로 인해 장대레일 궤도에는 매우 큰 압축력이 작용하게 되고, 이는 장대레일 궤도의 장출(좌굴)을 발생시켜 열차의 탈선으로 인한 사고로 이어진다. 본 연구에서는 장대레일 궤도의 좌굴에 많은 영향을 주는 궤도의 구성요소들 중에서 레일의 단면적과 단면2차모멘트 그리고 체결구의 파손과 병진 및 회전방향의 강성이 장대레일 궤도의 좌굴에 미치는 민감도를 파악하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 학술대회지
• /
• pp.780-783
• /
• 2004

The two-dimensional modeling of the non-stationary thermal state and voltage responsivity of the sensitive elements usually used in solid-state pyroelectric focal plane arrays are presented. Temperature distributions under periodical thermal excitation and the response of the thermal imaging device, which is composed of the pyroelectric sensitive elements mounted on a single silicon substrate, are numerically calculated. The sensitive element consists of a covering metal layer, infrared polymer absorber, front metal contact, sensitive pyroelectric element, the interconnecting column and the bulk silicon readout. The results of the numerical modeling show that the thermal crosstalk between sensitive elements to be critical especially at low frequency (f < 10Hz) of periodically modulated light. It is also shown that the use of our models gives the possibility to improve the design, operating regimes and sensitivity of the device.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.184-189
• /
• 2000

Two types of fiber-optic sensors, EFPI(extrinsic Fabry-Perot interferometer) and FBG(fiber Bragg grating), have been investigated for measurement of thermal strain and temperature. The EFPI sensor is only for measurement of thermal strain and the FBG sensor is for simultaneous measurement of thermal strain and temperature. FBG temperature sensor was developed to measure strain-independent temperature. This sensor configuration consists of a single-fiber Bragg grating and capillary tube which makes it isolated from external strain. This sensor can then be used to compensate for the temperature cross sensitivity of a FBG strain sensor. These sensors are demonstrated by embedding them into a graphite/epoxy composite plate and by attaching them on aluminum rod and unsymmetric graphitelepoxy composite plate. All the tests were conducted in a thermal chamber with the temperature range $20-100^{\circ}C$. Results of strain measurements by fiber-optic sensors are compared with that from conventional resistive foil gauge attached on the surface.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.425-429
• /
• 2004

In real design of the high & interim pressure turbine casing, it is one of the important things to figure out its thermal strain exactly. In this paper, with the establishment of the new concept for the heat transfer coefficient of steam that is one of the factors in analysis of the thermal stress for turbine casing, an analysis was done for one of the high & interim pressure turbine casings in operating domestically. The sensitivity analysis of the heat transfer coefficient of steam to the thermal strain of the turbine casing was done with a 2-D simple model. The analysis was also done with switching of the material properties of the turbine casing and resulted in that the thermal strain of the turbine casing was not so sensitive to the heat transfer coefficient of steam. On the basis of this, 3-D analysis of the thermal strain for the high and interim pressure turbine casing was done.

• 대한기계학회논문집B
• /
• 제32권7호
• /
• pp.542-548
• /
• 2008

A thermal mass air flow sensor (MAFS), which consists of a micro-heater and thermo-resistive sensors on the silicon-nitride ($Si_3N_4$) thin membrane structure, is micro-fabricated by MEMS processes. Two thermo-resistive temperature sensors are located at $100{\mu}m$ upstream and downstream from the micro-heater respectively. The thermal characteristics are measured to find the best measurement indicator. The micro-heater is operated under constant power condition, and four flow indicators are investigated. The normalized temperature indicator shows good physical meaning and is easy to use in practice. It is found that the configurations and heating power of thermal-resistive elements are the dominant factors to determine the range of the flow measurement in the MAFS with higher sensitivity and accuracy.

• Carbon letters
• /
• 제12권3호
• /
• pp.162-166
• /
• 2011

Conducting polymer-coated multiwalled carbon nanotubes (MWCNTs) were prepared by template polymerization in order to enhance their gas sensitivity. This investigation of the conducting polymer phases that formed on the surface of the MWCNTs is based on field-emission scanning electron microscopy images. The thermal stability of the conducting polymer-coated MWCNTs was significantly improved by the high thermal stability of MWCNTs. The synergistic effects of the conducting polymer-coated MWCNTs improve the gas-sensing properties. MWCNTs coated with polyaniline uniformly show outstanding improvement in gas sensitivity to $NH_3$ due to the synergistic combination of efficient adsorption of $NH_3$ gas and variation in the conduction of electrons.

• 한국전기전자재료학회논문지
• /
• 제17권8호
• /
• pp.806-811
• /
• 2004

1-Hydroxy-4-(2-naphthalenesulfonyloxy) cyclohexane(1), 1,4-di-(2-naphthalenesulfonyloxy) cyclohexane(2), 1-hydroxy-4-(2-thiophenesulfonyloxy) cyclohexane(3), 1,4-di-(2-thiophenesulfonyloxy) cyclohexane(4) were synthesized and evaluated for their performance as novel acid amplifiers for 193 nm photoresists. These acid amplifiers(1-4) showed reasonable thermal stability at the usual resist-processing temperature, 9$0^{\circ}C$-12$0^{\circ}C$. And estimated by the sensitivity curve, (1)-(4) enhanced the sensitivity of poly(tert-butyl methacrylate) film by 1.2-1.4 times, compared to poly(tert-butyl methacrylate) film whithout acid amplifiers, in the presence of a photoacid generator.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1364-1369
• /
• 2004

New method for the design, fabrication, and calibration of micro-machined heat flux sensor has been developed. Two types of micro-machined heat flux sensor having different thicknesses of the thermal-resistance layer are fabricated using the MEMS technique. Photo-resist patterning using a chrome mask, bulk-etching and copper-nickel sputtering using a shadow mask are applied to make heat flux sensors, which are calibrated in the convection-type heat flux calibration facility. The sensitivity of the device varies with thermal-resistance layer, and hence can be used to measure the heat flux in heat-transfer phenomena.