• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.345-350
• /
• 1999

The effectiveness of software error compensation for thermally induced machine tool errors relies on the prediction accuracy of the pre-established thermal error models. The selection of optimal sensor locations is the most important in establishing these empirical models. In this paper, a methodology for the selection of optimal sensor locations is proposed to establish a robust linear model which is not subjected to collinearity. Correlation coefficient and time delay are used as thermal parameters for optimal sensor location. Firstly, thermal deformation and temperatures are measured with machine tools being excited by sinusoidal heat input. And then, after correlation coefficient and time delays are calculated from the measured data, the optimal sensor location is selected through hard c-means clustering and sequential selection method. The validity of the proposed methodology is verified through the estimation of thermal expansion along Z-axis by spindle rotation.

• Journal of the Korean Society of Safety
• /
• v.11 no.3
• /
• pp.10-19
• /
• 1996

Grinding temperature and thermal deformation(dimensional error) are studied theoretically and experimentally. The propose of this research is clarified loading phenomena and residual stress In order to guide nozzle's efficiency. The main results to be obtained are as follows ; 1) When grinding condition Is high efficient grinding, FEM program is developed about grinding heat and dimensional error. 2) Thermal deformation depend on temperature distribution is in good agreement with experimental results in case of little grinding energy flux but is comparatively in good agreement with in case of large (3.5$\times$10$^{6}$ J/m). 3) In terms of high efficient grinding at field(table speed 4m/min), grinding fluid (dilution 5/100) obtained a good workpiece quality and decreased a grinding temperature. 4) A surface roughness, dimensional error, residual stress and loading phenomena with guide nozzle are decreased and these results obtained a good workpiece quality.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.773-776
• /
• 2005

In this paper, For improving the positioning accuracy of hydrostatic table, relationship between temperature of atmosphere and thermal characteristics of hydrostatic table is analyzed, and influence of thermal characteristics on positioning accuracy is also analyzed experimentally. From the experimental results, it is confirmed that positioning error and repeatability is $0.21{\mu}m\;and\;0.18{\mu}m$ when the laser scale which has $0.01{\mu}m$ of resolution is used as feed-back unit. and also confirmed that thermal deformation of scale and supporter, which occurs by the temperature variation of atmosphere, works as limit of repeatability in long time operation.

• Journal of Mechanical Science and Technology
• /
• v.17 no.12
• /
• pp.2078-2086
• /
• 2003

As technology advances with development of new materials, it is important to measure the thermal diffusivity of material and to predict the heat transfer in the solid subject to thermal processes. The measurement of thermal properties can be done in a non-contact way using photothermal displacement spectroscopy. In this work, the thermal diffusivity was measured by analyzing the magnitude and phase of deformation gradient. We proposed a new data analysis method based on the real part of deformation gradient as the pump-probe offset value. As the result, compared with the literature value, the measured thermal diffusivities of materials showed about 3 % error.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.4
• /
• pp.70-75
• /
• 2001

In metal cutting, the machining accuracy is more affected by thermal errors than by geometric errors. This paper models of the thermal errors for error analysis and develops on-the-machine measurement system by which the volumetric error are measured and compensated. The thermal error is modeled by means of angularity errors of a column and thermal drift error of the spindel unit which are measured by the touch probe unit with a star type styluses, a designed spherical ball arti-fact, and five gap sensors. In order to analyze the thermal characteristics under several operating conditions, experiments performed with the touch probe unit and five gap sensors on the vertical and horizontal machining centers.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.3
• /
• pp.254-259
• /
• 2013

Ball screw system is widely used as a precision mechanical linear actuator that translates rotational motion to linear motion for its high efficiency, great stiffness and long life. Recently, according to the requirements of high accuracy and stiffness, the pre-load on the ball screw which means of remove the backlash in the ball screw is usually used. Because of the preload which means the frictional resistance between the screw and nut, becomes a dominating heat source and it generates thermal deformation of ball screw which is the reason for low accuracy of the positioning decision. There are several methods to solve the problem that includes temperature control, thermal stable design and error compensation. In the past years, researchers focused on the error compensation technique for its ability to correct ball screw error effectively rather than the capabilities of careful machine design and manufacturing. Significant amounts of researches have been done to real-time error compensation. But in this paper, we developed a series of cooling methods to get thermal equilibrium in the ball screw system. So we find the optimum cooling type for improving positioning error which caused by thermal deformation in the ball screw system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.187-192
• /
• 1993

Thermal deformation causes large amount of machine tool errors. In order to compensate for thermal and geometric errors of the machine tool an off-line geometric adaptive control (GAC) scheme was developed. THe GAC method was realized by using a measuring plate made of precision spheres. Error vectors and volumetric errors were measured by the measuring plate. Error compensation models were obtained from error vectors and a kinematic chain of machine tools. Reliability of the GAC system of thermal and geometric errors were confrimed by large amount of experiments.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.355-356
• /
• 2008

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.354-354
• /
• 2008

Recently, due to the tremendous growth of media technology, demands of the aspheric glass lens which is a high-performance and miniaturized is gradually increasing. Generally, the aspheric glass lens is manufactured by GMP(Grass Molding Press) method using WC(tungsten carbide) mold core. In this study, the thermal deformation which occurs in the cooling step of GMP was considered, and it was compensated the form of mold core. The lens which was molded by compensated mold core was satisfied that can be applied to the actual specifications.

• Journal of the Korea Convergence Society
• /
• v.8 no.5
• /
• pp.185-192
• /
• 2017

Machine tool errors can be divided into geometric error, thermal deformation error, and machining error. In this study, the influence of each error on the total error and the relative size of each error are quantitatively analyzed in 2D machining. The thermal deformation error and the machining error caused a relatively large error compared to the geometric error, which is directly related to the machining accuracy. In order to eliminate the error factors, the possibility of error compensation was examined by analyzing the measured error profile shape. As a result, about 40 ~ 50% error compensation was achieved for each error factor. Through this study, it is possible to construct a basic data base on machining, and it is expected that it will be able to compensate the machining error from the viewpoint of users.