• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.2002-2014
• /
• 1991

본 연구에서는 모재균열의 열림변위로 인한 변형을 고려하여, 모재균열 주위 의 응력분포를 구하기 위한 2차원 해석방법을 제안한다. 제안된 방법은 두께방향 다 항식 형태로 가정된 변위성분으로부터 모재균열 주쥐의 변위, 응력분포를 구한다. 본 방법은 적층판의 프아송비(Poisson's ratio) 효과와 열잔류응력(thermal residual stress)의 영향을 고려하였으며, 계면층(interface layer) 개념을 사용하여 특성손상 상태 이후에 발생하는 층간분리를 평가하기 위한 기초자료인 층간수직응력과 층간전단 응력을 결정하였다. 제안된 방법의 타당성을 검증하기 위하여, 유한요소해석(finite element analysis)을 수행하여 제안된 방법의 응력분포 결과를 유한요소해석 결과와 비교하여 보았다.

• 한국세라믹학회지
• /
• 제46권2호
• /
• pp.211-218
• /
• 2009

For the Y5V characteristic MLCC which is very prone to crack, it is important to to find out the basic cause of the crack. After finding out the crack origin, the materials and processes should be developed to remove the crack. The microstructures of the cracks were investigated using the fractographic method for the various types of cracks such as an exterior crack, a cyclic thermal shock crack, and an piezo-electric crack. It was found out that the crack origin was the pore at the end of the Ni inner electrode after bake-out. Even though the three dimensional crack shapes were different, the crack origins were seemed to be similar. The exterior crack could grow from the origin with the aids of residual and applied stress. FEM (finite element method) analysis was used to calculate the stress distribution of residual and applied stress. And the concept of fracture mechanics was applied for the explanation of the crack initiation and propagation from the stresses concentration.

• 대한기계학회논문집A
• /
• 제25권7호
• /
• pp.1139-1146
• /
• 2001

The reactor pressure vessel(RPV) is usually cladded with stainless steel to prevent corrosion and radiation embrittlement, and a number of subclad cracks have been found during an in-service-inspection. These subclad cracks should be assured for a safe operation under normal conditions and faulted conditions such as pressurized thermal shock(PTS). Currently available integrity assessment procedure for an RPV, ASME Code Sec. XI, are built on the basis of linear fracture mechanics (LEFM). In PTS condition, however, thermal stress and mechanical stress give rise to high tensile stress at the cladding and elastic-plastic behavior is expected in this area. Therfore, ASME Code Sec. XI is overly conservative in assessing the structural integrity under PTS condition. In this paper, the fracture parameter (stress intensity factor, K, and RT(sub)NDT) from elastic analysis using ASME Sec. XI and finite element method were validated against 3-D elastic-plastic finite element analyses. The difference between elastic and elastic-plastic analysis became significant with increasing crack depth. Therfore, it is recommended to perform elastic-plastic analysis for the accurate assessment of subclad cracks under TPS which causes plastic deformation at the cladding.

• Nuclear Engineering and Technology
• /
• 제47권6호
• /
• pp.712-718
• /
• 2015

Cast duplex stainless steels are susceptible to thermal aging during long-term service at temperatures ranging from $280^{\circ}C$ to $450^{\circ}C$. To analyze the effect of thermal aging on leak-before-break (LBB) behavior, three-dimensional finite element analysis models were built for circumferentially cracked pipes. Based on the elasticeplastic fracture mechanics theory, the detectable leakage crack length calculation and J-integral stability assessment diagram approach were carried out under different bending moments. The LBB curves and LBB assessment diagrams for unaged and thermally aged pipes were constructed. The results show that the detectable leakage crack length for thermally aged pipes increases with increasing bending moments, whereas the critical crack length decreases. The ligament instability line and critical crack length line for thermally aged pipes move downward and to the left, respectively, and unsafe LBB assessment results will be produced if thermal aging is not considered. If the applied bending moment is increased, the degree of safety decreases in the LBB assessment.

• 한국생산제조학회지
• /
• 제7권3호
• /
• pp.68-78
• /
• 1998

Welding structure contains residual stress due to thermal-plastic strain during welding process, and its magnitude and distribution depend on welding conditions. Cracks initiate from various defects of the weldment, propagate and lead to final fracture, The crack initiation and propagation processes are affected by the magnitude and distribution. Therefore, the magnitude and distribution of weldment residual stress should be considered for safety design and service of welding structures. Also it is very important that more accurate assessment method of fatigue crack growth must take into account the redistributing the residual stress quantitively. because the residual stress in weldment has characteristics of its redistribution with loading magnitude, number of cycles and fatigue crack propagation. In this study fatigue crack behavior of STS-304 weldment was investigated during crack propagation into tensile residual stress region or compressive residual stress region. Crack growth rates were predicted and compared with experimental results.

• Journal of Welding and Joining
• /
• 제17권1호
• /
• pp.124-132
• /
• 1999

Thermal fatigue strength of the solder joints is the most critical issue for TSOP(Thin Small Outline Package) because the leads of this package are extremely short and thermal deformation cannot be absorbed by the deflection of the lead. And the TSOP body can be subject to early fatigue failures in thermal cycle environments. This paper was discussed distribution of thermal stresses at near the joint between silicon chip and die pad and investigated their reliability of solder joints of TSOP with 42 alloy clad lead frame on printed circuit board through FEM and 3 different thermal cycling tests. It has been found that the stress concentration around the encapsulated edge structure for internal crack between the silicon chip and Cu alloy die pad. And using 42 alloy clad, The reliability of TSOP body was improved. In case of using 42 alloy clad die pad(t=0.03mm). $$\sigma$_{VMmax}$ is 69Mpa. It is showed that 15% improvement of the strength in the TSOP body in comparison with using Cu alloy die pad $($\sigma$_{VMmax}$=81MPa). In solder joint of TSOP, the maximum equivalent plastic strain and Von Mises stress concentrate on the heel of solder fillet and crack was initiated in it's region and propagated through the interface between lead and solder. Finally, the modified Manson-Coffin equation and relationship of the ratio of $N_{f}$ to nest(η) and cumulative fracture probability(f) with respect to the deviations of the 50% fracture probability life $(N_{f 50%})$ were achieved.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 추계학술발표대회
• /
• pp.11.2-11.2
• /
• 2009

Au-Ag 합금 박막에서 화학적으로 덜 안정한 Ag를 선택적으로 에칭하는 dealloying 기법을 통하여 crack-free 나노기공 gold 박막을 Si 기판에 제조하였다. Au-Ag 합금 박막은 두 가지 방법을 이용하였다: 1) thermal 또는 electron beam 증착법을 이용하여 Au 와 Ag 다층 박막을 Si 기판에 증착시킨 후 열처리를 통한 합금 박막제조; 2) co-thermal 증착법을 이용하여 Au-Ag 합금박막을 Si 기판에 직접 증착. Crack-free 나노기공 gold 박막 제조에 적합한 합금조성을 얻기 위하여 증착 속도, 열처리조건, dealloying 조건등을 조절하였다. Perchloric acid, HClO4 전해질을 이용한 전기화학적 dealloying을 통하여 crack-free 나노기공 gold 박막을 제조하였고, 기공크기를 조절할 수 있었다. 이에 더하여, electrophoretic 방법을 이용하여 나노기공 gold와 semiconductive 양자점 (CdTe 또는 CdSe)의 나노복합박막을 형성시킨 후 특성을 분석하였다.

• Journal of Welding and Joining
• /
• 제11권4호
• /
• pp.103-111
• /
• 1993

Recently, several high-tensile steels(e.g. 80kg and above, $2^{1/4}Cr$-1Mo)having good quality to high temperature and pressure-resistance are widely used to construct petroleum-plant and pressure vessel of heat or nuclear-power plant. However, in the steels, reheating crack at grain boundaries of the heat affected zone(HAZ) occures during post welding heat treatment(PWHT)to remove welding residual stress. In order to study theoretically the characteristics of reheating crack created by PWHT, the computer program of three-dimensional thermal-elasto-plasto-creep analysis based on finite element method are developed, and then the mechanical behavior(history of creep strain accumulation and stress relaxation, etc)of welded join in thick plate during PWTH is clarified by the numerical results.

• 한국군사과학기술학회지
• /
• 제23권6호
• /
• pp.574-581
• /
• 2020

This paper describes the stacking effect for Ceramic Column Grid Array(CCGA) packages used for satellites. Reflow Soldering Process suitable for CCGA package with back structure was set as the process development goal to meet European Cooperation for Space Standardization(ECSS) standard. After analyzing the stacking effect according to the type of CCGA, it is verified by applying it to the CCGA Reflow Soldering Process. In order to confirm the validity of the staking effect analyzed in terms of vibration and thermal characteristics, it is verified through actual specimen production. It analyzes the cause of crack occurrence in the CCGA package and estimates the crack generation point using previously acquired inspection data.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.445-448
• /
• 2006

In order to control the temperature crack of massive dam concrete, the selection of appropriate materials like binder, aggregates etc., is essential. To select the optimal mix proportion, ordinary portland cement(Type I) plus 25% of fly ash and low heat portland cement(Type IV) are used as binder, and 80mm of coarse aggregates are used to reduce the amount of binder and compare the compressive strength, hydration temperature and crack index. The results of this study are as following. 1. The strength of Type IV cement is advantageous on the long-term age. 2. According to the temperature measured on mock-up$(1.5m{\times}1.5m{\times}1.5m)$, and realized the thermal analysis, the Type IV cement carried out advantageous to control the thermal crack.