• Current Photovoltaic Research
• /
• 제2권3호
• /
• pp.88-94
• /
• 2014

The structural, optical and electrical properties of sputter-deposited CIGS films were directly influenced by the sputtering process parameters such as substrate temperature, working pressure, RF power and distance between target and substrate. CIGS thin films deposited by using a quaternary target revealed to be Se deficient due to Se low vapor pressure. This Se deficiency affected the overall stoichiometry of the films, causing the films to be Cu-rich. Current tends to pass through the Cu-Se channels which act as the shunting path increasing the film conductivity. The crystal structure of CIGS thin films depends on the substrate orientation due to the influence of surface morphology, grain size and stress of Mo substrate. The excess of Cu was removed from the CIGS films by KCN treatment, achieving a suitable Cu concentration (referred as Cu-poor) for the fabrication of solar cell. Due to high Cu concentrations on the CIGS film surface induced by Cu-Se phases after CIGS film deposition, KCN treatment proved to be necessary for the fabrication of high efficiency solar cells. Also during KCN treatment, dislocation density and lattice parameter decreased as excess Cu was removed, resulting in increase of bandgap and the decrease of conductivity of CIGS films. It was revealed that Cu-Se secondary phase could be removed by KCN wet etching of CIGS films, allowing the fabrication of high efficiency absorber layer.

• Archives of Plastic Surgery
• /
• 제36권6호
• /
• pp.743-749
• /
• 2009

Purpose: Many researches about various surgical method for blepharoptosis have already been introduced. But researches for complications after blepharoptosis correction is relatively insufficient. So, this study was performed to recognize common complications that arised depending on the severity of blepharoptosis, levator function and surgical method. Methods: 250 patients who have underwent surgical treatment for blepharoptosis from 1987 to 2006 were employed in this study. Patients were categorized by severity of blepharoptosis, levator function and surgical method that has been used. Complications after blepharoptosis correction were analyzed. Result: Total of 64 patients had occurred complications, the specifics are as following; undercorrection 22, asymmetry 13, overcorrection 12, lagophthalmos 4, abnormal eyelid contour 4, exposure keratitis 3, ectropion 2, inclusion cyst 2, infection 1 and conjunctival prolapse 1. Among above patients, 3 patients had two kinds of complications. 21 patients was underwent secondary surgery due to complication. Conclusion: Evaluating the outcomes of the secondary surgery, the early correction was better than the late correction. The most of the complications were recovered through conservative and surgical treatments. The most of the complications (47 patients) were undercorrection, asymmetry, overcorrection and took 73.4% of the total complications. The more severe the blepharoptosis and the more poor the levator function, the rate of complications were higher. According to the operation methods, most complications were occurred in levator operation, frontalis transfer and OOM flap.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제49권1호
• /
• pp.13-20
• /
• 2023

Objectives: Ultra-wide implants may be used as a replacement if existing implants fail. This study was conducted to evaluate the factors influencing the prognosis and failure of ultra-wide implants. Patients and Methods: This study evaluated whether sex, age, site, diameter, length, additional surgery, implant stability (primary and secondary), and reason for ultra-wide implant placement affect the 5-year survival and success rates and marginal bone loss (MBL) of ultra-wide implants. Seventy-eight ultra-wide implants that were placed in 71 patients (39 males and 32 females) from 2008 to 2010 were studied. One-way ANOVA analysis was conducted to evaluate the statistical significance of MBL according to the patient's sex, implant site, and diameter. Independent sample t-tests were used to determine the statistical significance of MBL analysis which was used to determine the significance of the 5-year success and survival rates related to the variables. One-way ANOVA was conducted to evaluate the statistical significance of sex, implantation site, diameter, and MBL. Independent sample t-tests were used to evaluate the correlation between implantability and MBL for implantation reasons, while additional surgery, length, and Kaplan-Meier analysis were used to evaluate 5-year survival and success rates. Results: The mean age of patients was 54.2 years with a survival rate of 92.3% and a success rate of 83.3% over a mean 97.8-month period of observation. MBL averaged 0.2 mm after one year of prosthetic function loading and 0.54 mm at the time of final observation. Success rates correlated with primary stability (P=0.045), survival rates correlated with secondary stability (P=0.036), and MBL did not correlate with any variables. Conclusion: Ultra-wide implants can be used to achieve secure initial fixation in the maxillary and mandibular molar regions with poor bone quality or for alternative purposes in cases of previous implant failure.

• Journal of Korean Neurosurgical Society
• /
• 제40권1호
• /
• pp.11-15
• /
• 2006

Objective : Acute cerebral infarction is often accompanied by transtentorial herniation which can be fatal. The aim of this study is to determine the timing of surgical intervention and prognostic factors in patients who present with acute cerebral infarction. Methods : We reviewed retrospectively 23 patients with acute cerebral infarction, who received decompressive craniectomy or conservative treatment from January 2002 to December 2004. We divided patients into two groups according to the treatment modalities [Group 1 : conservative treatment, Group 2 : decompressive craniectomy]. In all patients, the outcome was quantified with Glasgow Outcome Scale and Barthel Index. Results : Of the 23 patients, 11 underwent decompressive craniectomy. With decompressive craniectomy at the time of loss of pupillary light reflex, we were able to prevent death secondary to severe brain edema in all cases. Preoperative Glasgow Coma Scale and loss of pupillary light reflex were significant to the clinical outcome statistically. With conservative treatment, 9 of the 12 patients died secondary to transtentorial herniation. The clinical outcomes of remaining 3 patients were poor. Conclusion : This study confirms the value of life-saving procedure of decompressive craniectomy after acute cerebral infarction. We propose that the loss of pupillary light reflex should be considered one of the most important factors to determine the timing of the decompressive craniectomy.

• Journal of Microbiology and Biotechnology
• /
• 제27권10호
• /
• pp.1867-1876
• /
• 2017

Most of the biosynthetic pathways for secondary metabolites are influenced by carbon metabolism and supply of cytosolic NADPH. We engineered carbon distribution to the pentose phosphate pathway (PPP) and redesigned the host to produce high levels of NADPH and primary intermediates from the PPP. The main enzymes producing NADPH in the PPP, glucose 6-phosphate dehydrogenase (encoded by zwf1 and zwf2) and 6-phosphogluconate dehydrogenase (encoded by zwf3), were overexpressed with opc encoding a positive allosteric effector essential for Zwf activity in various combinations in Streptomyces lividans TK24. Most S. lividans transformants showed better cell growth and higher concentration of cytosolic NADPH than those of the control, and S. lividans TK24/pWHM3-Z23O2 containing zwf2+zwf3+opc2 showed the highest NADPH concentration but poor sporulation in R2YE medium. S. lividans TK24/pWHM3-Z23O2 in minimal medium showed the maximum growth (6.2 mg/ml) at day 4. Thereafter, a gradual decrease of biomass and a sharp increase of cytosolic NADPH and sedoheptulose 7-phosphate between days 2 and 4 and between days 1 and 3, respectively, were observed. Moreover, S. lividans TK24/pWHM3-Z23O2 produced 0.9 times less actinorhodin but 1.8 times more undecylprodigiosin than the control. These results suggested that the increased NADPH concentration and various intermediates from the PPP specifically triggered undecylprodigiosin biosynthesis that required many precursors and NADPH-dependent reduction reaction. This study is the first report on bespoke metabolic engineering of PPP routes especially suitable for producing secondary metabolites that need diverse primary precursors and NADPH, which is useful information for metabolic engineering in Streptomyces.

• 한국의학물리학회지:의학물리
• /
• 제33권4호
• /
• pp.108-113
• /
• 2022

Purpose: Proton therapy has been used for optimal cancer treatment by adapting its Bragg-peak characteristics. Recently, a tissue-sparing effect was introduced in ultrahigh-dose-rate (FLASH) radiation; the high-energy transmission proton beam is considered in proton FLASH therapy. In measuring high-energy/ultrahigh-dose-rate proton beam, Faraday Cup is considered as a dose-rate-independent measurement device, which has been widely studied. In this paper, the feasibility of the simply designed Faraday Cup (Poor Man's Faraday Cup, PMFC) for transmission proton FLASH therapy is investigated. Methods: In general, Faraday cups were used in the measurement of charged particles. The simply designed Faraday Cup and Advanced Markus ion chamber were used for high-energy proton beam measurement in this study. Results: The PMFC shows an acceptable performance, including accuracy in general dosimetric tests. The PMFC has a linear response to the dose and dose rate. The proton fluence was decreased with the increase of depth until the depth was near the proton beam range. Regarding secondary particles backscatter from PMFC, the effect was negligible. Conclusions: In this study, we performed an experiment to investigate the feasibility of PMFC for measuring high-energy proton beams. The PMFC can be used as a beam stopper and secondary monitoring system for transmission proton beam FLASH therapy.

• 여성건강간호학회지
• /
• 제28권2호
• /
• pp.112-122
• /
• 2022

Purpose: The prevalence of osteoporosis in postmenopausal women is increasing, and diabetes patients have decreased bone density. Their health-related quality of life (HRQoL) is diminished by the resultant physical dysfunction and depression. The purpose of this study was to identify factors influencing HRQoL in postmenopausal women with diabetes and osteoporosis. Methods: This was a secondary data analysis of the Seventh Korea Health and Nutrition Examination Survey (2016-2018), which utilized a complex, multistage probability sample design. The participants in the study were 237 women with diabetes and osteoporosis. To evaluate the factors that influenced HRQoL, a complex-samples general linear model was constructed, and the Bonferroni correction was performed. Results: In this sample of women aged 45 to 80 years (mean±standard deviation, 71.12±7.21 years), the average HRQoL score was 0.83±0.18 out of 1.0. Factors influencing HRQoL were age (70s: t=-3.74, p<.001; 80s: t=-3.42, p=.001), walking for exercise more than 5 days a week (t=-2.83, p=.005), cerebrovascular disease (t=-8.33, p<.001), osteoarthritis (t=-2.04, p=.014), hypertension (t=2.03, p=.044), higher perceived stress (t=-2.17, p=.032), poor glycemic control (t=3.40, p=.001), waist circumference (t=-2.76, p=.007), sitting time per day (t=-2.10, p=.038), and a longer postmenopausal period (t=3.09, p=.002). Conclusion: In order to improve the HRQoL of postmenopausal women with osteoporosis and diabetes, it is necessary to implement intervention strategies that enable the effective management of chronic diseases, while preventing the complications of diabetes and minimizing stress through physical activity.

• 한국분말재료학회지
• /
• 제26권5호
• /
• pp.395-404
• /
• 2019

Aluminum nitride (AlN) has excellent electrical insulation property, high thermal conductivity, and a low thermal expansion coefficient; therefore, it is widely used as a heat sink, heat-conductive filler, and heat dissipation substrate. However, it is well known that the AlN-based materials have disadvantages such as low sinterability and poor mechanical properties. In this study, the effects of addition of various amounts (1-6 wt.%) of sintering additives $Y_2O_3$ and $Sm_2O_3$ on the thermal and mechanical properties of AlN samples pressureless sintered at $1850^{\circ}C$ in an $N_2$ atmosphere for a holding time of 2 h are examined. All AlN samples exhibit relative densities of more than 97%. It showed that the higher thermal conductivity as the $Y_2O_3$ content increased than the $Sm_2O_3$ additive, whereas all AlN samples exhibited higher mechanical properties as $Sm_2O_3$ content increased. The formation of secondary phases by reaction of $Y_2O_3$, $Sm_2O_3$ with oxygen from AlN lattice influenced the thermal and mechanical properties of AlN samples due to the reaction of the oxygen contents in AlN lattice.

• 한국표면공학회지
• /
• 제56권1호
• /
• pp.62-68
• /
• 2023

Silicon (Si) is considered as a promising substitute for the conventional graphite due to its high theoretical specific capacity (3579 mAh/g, Li₁₅Si₄) and proper working voltage (~0.3V vs Li⁺/Li). However, the large volume change of Si during (de)lithiation brings about severe degradation of battery performances, rendering it difficult to be applied in the practical battery directly. As a one feasible candidate of industrial Si anode, silicon monoxide (SiO_x) demonstrates great electrochemical stability with its specialized strategy, downsized Si nanocrystallites surrounded by Li⁺ inactive buffer phase (Li₂O and Li₄SiO₄). Nevertheless, SiO_x inherently has the initial irreversible capacity and poor electrical conductivity. To overcome those issues, conformal carbon coating has been performed on SiO_x utilizing ethylbenzene as the carbon precursor of chemical vapor deposition (CVD). Through various characterizations, it is confirmed that the carbon is homogeneously coated on the surface of SiO_x. Accordingly, the carbon-coated SiOx from CVD using ethylbenzene demonstrates 73% of the first cycle efficiency and great cycle life (88.1% capacity retention at 50th cycle). This work provides a promising synthetic route of the uniform and scalable carbon coating on Si anode for high-energy density.

• 한국축산식품학회지
• /
• 제43권2호
• /
• pp.220-231
• /
• 2023

Although omega-3 fatty acids including docosahexaenoic acid (DHA) contain various health-promoting effects, their poor aqueous solubility and stability make them difficult to be induced in dairy foods. The aims of this research were to manufacture casein derivative-based delivery system using acid-induced gelation method with glucono-σ-lactone and to investigate the effects of production variables, such as pH and charged amount of linoleic acid, on the physicochemical properties of delivery systems and oxidative stability of DHA during storage in model milk. Covalent modification with linoleic acid resulted in the production of casein derivatives with varying degrees of modification. As pH was reduced from 5.0 to 4.8 and the charged amount of linoleic acid was increased from 0% to 30%, an increase in particle size of casein derivative-based delivery systems was observed. The encapsulation efficiency of DHA was increased with decreased pH and increased charged amount of linoleic acid. The use of delivery system for DHA resulted in a decrease in the development of primary and secondary oxidation products. An increase in the degree of modification of casein derivatives with linoleic acid resulted in a decrease in the formation of primary and secondary oxidation products than of free DHA indicating that delivery systems could enhance the oxidative stability of DHA during storage in model milk. In conclusions, casein derivatives can be an effective delivery system for DHA and charged amount of linoleic acid played a key role determining the physicochemical characteristics of delivery system and oxidative stability of DHA.