• Journal of the Institute of Convergence Signal Processing
• /
• v.19 no.3
• /
• pp.125-132
• /
• 2018

KVN(Korean VLBI Network) introduced the Mark6 system of the MIT haystack observatory as a recorder for data recording up to 32 Gbps for VLBI(Very Long Baseline Interferometry) observation. The Mark6 recorder can record data at up to 32Gbps when two systems and 64 HDDs are installed. However, because of the unique recording method that is characteristic of Mark6, we are introducing a large amount of data into a virtual file system, or using a general RAID method, which causes data loss when reading and transferring files at the highest recording speed or file system have. The Flexbuff system, a software recorder developed by JIVE(Joint Institute for VLBI ERIC), can be configured to operate as a data recorder through RAID configuration and network upgrades. In particular, when installed in the Mark6 system, it can record VLBI data at a maximum speed of 32 Gbps with less loss of data compared to the existing Mark6 by utilizing Mark6 resources well. In this paper, we propose that the existing Mark6 system can be operated as Mark6-Flexbuff by installing jive5ab software, and it is verified through experiment that it can be effectively used for VLBI observation operation through data recording test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.118-124
• /
• 2011

To reach the Euro-6 regulations of PM and $NO_x$ for light-duty diesel vehicles, it will be necessary to apply the CDPF and the de-$NO_x$ catalyst. The described system consists of a catalytic configuration, where the CDPF is placed downstream of the diesel engine and followed by a urea injection unit and a urea-SCR catalyst. One of the advantages of this system configuration is that, in this way, the SCR catalyst is protected from PM, and both white PM and deposits become reduced. In the urea-SCR system, the injection control of reductant is the most important thing in order to have good performance of $NO_x$ reduction. The ideal ratio of $NH_3$ molecules to $NO_x$ molecules is 1:1 based on $NH_3$ consumption and having $NH_3$ available for reaction of all of the exhaust $NO_x$. However, under the too low and too high temperature condition, the $NO_x$ reduction efficiency become slower, due to temperature window of SCR catalyst. And space velocity also affects to $NO_x$ conversion efficiency. In this paper, rig-tests were performed to evaluate the effects of $NO_x$ and $NH_3$ concentrations, gas temperature and space velocity on the $NO_x$ conversion efficiency of the urea-SCR system. And vehicle test was performed to verify control strategy of reductatnt injection. The developed control strategy of reductant injection was improved over all $NO_x$ reduction efficiency and $NH_3$ consumption in urea-SCR system. Results of this paper contribute to develop urea-SCR system for light-duty vehicles to meet Euro-5 emission regulations.

• The Journal of the Convergence on Culture Technology
• /
• v.10 no.1
• /
• pp.411-417
• /
• 2024

In the event of a disaster, it is essential to establish a disaster recovery plan and disaster recovery system to minimize disruption to major IT infrastructure and provide continuous business services. In the process of building a disaster recovery system, data replication is a key element of data recovery to provide uninterrupted and continuous business services in the event of a disaster. The data replication method can be determined depending on the system configuration environment and disaster recovery goal level. In this paper, we present a method for determining a data replication method suitable for the configuration environment and disaster recovery target level when building a disaster recovery system. In addition, the replication method decision procedure is applied to build a disaster recovery system and analyze the construction results. After establishing the disaster recovery system, a test was conducted to determine whether the service was transferred to the disaster recovery center in a disaster situation and normal service was provided, and the results were analyzed. As a result, it was possible to systematically select the optimal data replication method during the disaster recovery system construction phase. The established disaster recovery system has an RTO of 3.7 hours for service conversion to the disaster recovery center to provide continuous business services, and the disaster recovery level, which was Tier 2, has been improved to the target level within 4 hours of RTO and RPO=0.

• Journal of the Korea Concrete Institute
• /
• v.16 no.5 s.83
• /
• pp.687-696
• /
• 2004

It has been known that practically unavoidable lap splices of longitudinal reinforcement in the plastic hinge region have a bad effect on the seismic performance of reinforced concrete bridge columns. Lap splices were usually located in the plastic hinge region of most bridge columns designed before the implementation of the new seismic design provisions of 1992 Korea Bridge Design specification. The objective of this research is to evaluate the seismic performance of full-sized reinforced concrete bridge piers with lap splice of longitudinal reinforcement in the plastic hinge region, and to develop an appropriate lateral confinement concept of RC bridge columns with lap-spliced longitudinal steels in low or moderate seismicity region. Eight test specimens in the aspect ratio of 4.0 were made with three types of lap splicing, two levels of confinement steel ratios and two types of tie configurations. It was confirmed from the Quasi-Static test that displacement ductility ratios were significantly reduced for nonseismic test columns with lap spliced longitudinal steels but were satisfied the seismic requirement for limited ductile design specimens. As a conclusion, pertinent lateral confinement content was proposed for the seismic. performance of RC bridge piers with $50\%$ lap-spliced longitudinal reinforcing steels in low or moderate seismicity region.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.54 no.2
• /
• pp.107-115
• /
• 2018

In this study, we tested Japanese trolling lines in the Jeju fishery. This fishery simulates the natural marine environment with many seabed rocks, and has been redesigned and manufactured it to be suitable for the Jeju fishery. In order to ensure that the trolling lines were deployed at the inhabitation depth of hairtails, the conditions required for the fishing gear to reach the target depth were determined for use during the experiment. The experimental test fishing was conducted at the depth of 120 m water in front of Jeju Seongsanpo and in the offshore area of Jeju Hanlim. The fishing gear used in the test fishing is currently used in a variety of field operations in Japan. However, several problems were identified, such as twisting of the line during its deployment and excessive sinking of the main line. The fishing gear was, therefore, redesigned and manufactured to be more suitable for the Jeju fishery environment. For the fishing gear to accurately reach the target depth, depth loggers were installed at the starting point of the main line and at the 250 m and 340 m points of the line. Depth and time were recorded every 10 seconds. According to the daytime positioning of hairtails in the lower water column, the target depth of the fishing gear was set at 100-110 m, which was 10-20 m above the sea floor. At a speed of 1.9 knots and with a 9 kg sinker attached, the main fishing line was deployed and catch yields at depths of 100 m, 150 m and 180 m were recorded and analyzed. When the 180 m main line was fully deployed, the time for the hairtail trolling lines to arrive at the appropriate configuration had to be 5 minutes. At this time, the depth of the fishing gear was 16-23 m above the sea floor, in accordance with the depths at which the hairtails were during the day. In addition, in order to accurately place the fishing gear at the inhabitation water depth of hairtails, the experimental test fishing utilized the results of the depth testing that identified the conditions required for the fishing gear to reach the target depth, and the result was a catch of up to 97 kg a day.

• Tunnel and Underground Space
• /
• v.28 no.3
• /
• pp.258-276
• /
• 2018

The accurate and quantitative ground information on the hydraulic conductivity characteristics of rock mass is one of the key factors for evaluation of the hydro-geological behaviour of rock mass around an excavated opening under high water pressure. For tunnel and rock structures in seabed, where the sea acts as an infinite source of water, its importance become greater with increasing construction depth below sea level. In this study, to improve the problems related with poor system configuration and incorrect data acquisition of previous hydraulic packer testing equipment, we newly developed an integrated main frame and 30 bar level waterproof downhole sonde apparatus, which were optimized for deep hydraulic packer test in seabed rock mass. Integration of individual test equipment into one frame allows safe and efficient field testing work on a narrow offshore drilling platform. For the integrated type main frame, it is possible to make precise stepwise control of downhole net injection pressure at intervals of $2.0kg_f/cm^2$ or less with dual hydraulic oil volume controller. To ensure the system performance and the operational stability of the prototype mainframe and downhole sonde apparatus, the field feasibility tests were completed in two research boreholes, and using the developed apparatus, the REV(Representative Elementary Volume) scale deep hydraulic packer tests were successfully carried out at a borehole located in the basalt region, Jeju. In this paper, the characteristics of the new testing apparatus are briefly introduced and also some results from the laboratory and in-situ performance tests are shown.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.11
• /
• pp.1413-1420
• /
• 2012

To predict the dynamics behavior, running stability, etc. of a railway vehicle and to understand its physical characteristics, analytical methods are used for the testing and manufacturing of a scale model along with numerical simulations in developed countries (England, France, Japan, etc.). The test of the dynamics characteristics of full-scale models is problematic in that it is expensive and time-consuming because an entire large-scale test plant needs to be constructed, difficulties are involved in the test configuration, etc. To overcome these problems, an analytical study involving dynamics tests and computer simulations using a scaled bogie model that applies the laws of similarity was carried out. In this study, we performed stability analysis on a 1/5 small scaled bogie for parameters such as the running speed and carbody weight by using an analysis model. Furthermore, we verified the reliability by using a small-scaled derailment simulator and examined the dynamic characteristic of the 1/5 small scaled bogie.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.2
• /
• pp.63-67
• /
• 2011

We investigated effects of bonding conditions on the peel strength of rigid printed circuit board (RPCB)/ flexible printed circuit board (FPCB) joints bonded using a thermo-compression bond method, The electrodes on the FPCB were coated with Sn by a dipping process. We confirmed that the bonding temperature and bonding time strongly affected the bonding configuration and strength of the joints. Also, the peel strength is affected by dipping conditions; the optimum dipping condition was found to be temperature of $270^{\circ}C$ and time of 1s. The bonding strength linearly increased with increasing bonding temperature and time until $280^{\circ}C$ and 10s. The fracture energy calculated from the F-x (Forcedisplacement) curve during a peel test was the highest at bonding temperature of $280^{\circ}C$.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.8 no.4
• /
• pp.335-344
• /
• 2006

The domestic standards which used the standards of Road Association of Japan standards presents the distances of between jet-fans by the caliber of jet-fan. However, the Permanent International Association of Road Congress (PIARC) encourages it to be ten times a diameter of the tunnel. The distance of jet-fans installed in bases of two standards differs as much as two times, as so the proper basis after analysis of internal air current is needed since such difference can lead to disadvantage for selection of ventilation configuration. Based on Froude modeling theory, 1/40 scale acrylic model of a tunnel (215mm in diameter and 6.9m in length) and jet-fan (26.3mm and 31.6mm in caliber) was made for the measurement of changes in pressure and velocity due to the extension of tunnel for analysis of internal air current. And we measured the changes in pressure of surroundings of a jet-fan for confirmation of recirculation due to the exterior airs when the jet-fan is on. The results of the model test show that internal air current was not influenced by the caliber of jet-fan and its changes in pressure and velocity were stable in the point where it was nine times of diameter of the tunnel. Also the recirculation when the jet-fan is on could be verified. According to such results, in the cases of installing jet-fan in tunnels, the distances between jet-fans needs to be more than nine times the diameter.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.5
• /
• pp.1069-1076
• /
• 2017

C-ITS(Cooperative-Intelligent Transportation System) provides services that require strict real-time such as forward collision warning, road safety service and emergency stop. WAVE(Wireless Access in Vehicular Environments), a core technology of C-ITS, is a technology designed for high-speed driving. However, in order to provide stable communication service by applying to real road environment, various performance tests of real vehicular environment are required. In the real road environment, WAVE communication performance is influenced by the surrounding environment such as moving vehicle, road shape and topography. Especially, when the vehicle is moving at high speed, the traveling position according to the speed of the vehicle, The surrounding environment changes rapidly. Such changes are factors affecting the communication performance, therefore a system and methods for analyzing them are needed. In this paper, we propose the configuration and test method of an effective performance evaluation system under high-speed driving and describe the results of analyzing the communication performance based on the data measured through the actual vehicle test.