• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.1
• /
• pp.120-127
• /
• 1991

The purpose of this study is to develop a fault detection and diagnosis scheme that can monitor process fault and instrument fault of a steam generator. The suggested scheme consists of a Kalman filter and two bias estimators. Method of detecting process and instrument fault in a steam generator uses the mean test on the residual sequence of Kalman filter, designed for the unfailed system, to make a fault decision. Once a fault is detected, two bias estimators are driven to estimate the fault and to discriminate process fault and instrument fault. In case of process fault, the fault diagnosis of outlet temperature, feed-water heater and main steam control value is considered. In instrument fault, the fault diagnosis of steam genrator's three instruments is considered. Computer simulation tests show that on-line prompt fault detection and diagnosis can be performed very successfully.

• Composites Research
• /
• v.14 no.1
• /
• pp.15-21
• /
• 2001

The pressing roller was designed and manufactured with high modulus carbon fiber composite material to exploit the high specific stiffness of the composite material. the optimal stacking sequence for the pressing roller was obtained from the FE analysis and the shape of the rubber coating layer was determined based on the calculated deflection for the uniform pressure on the film along the axial length of the pressing roller. Then the static deflection of the manufactured composite pressing roller was experimentally evaluated in comparison with analysis result and dynamic characteristics were measured through vibrational test.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.465-472
• /
• 1999

A small scale model reinforced soil wall was constructed in a laboratory to investigate role of the wall facing and the effect of construction sequence on the wall. A panel type facing system and a block facing system are introduced for test. These two different types of facing adapt different construction procedure. The model wall is built with geogrid reinforcement, sand, and the facings on rigid surface. The model wall is instrumented with earth pressure gauges, LVDTs, and strain gauges. It is found in this study that the reinforced soil wall system built with geogrids and panel type facing system be the safest reinforced soil wall ever compared to the block type facing. Thus, it is recommended that study for the wall system be necessary for further wide usage in the future.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.170-175
• /
• 2001

The design cycle associated with large engineering systems requires an initial decomposition of the complex system into design processes which are coupled through the transference of output data. Some of these design processes may be grouped into iterative subcycles. In analyzing or optimizing such a coupled system, it is essential to determine the best order of the processes within these subcycles to reduce design cycle time and cost. This is accomplished by decomposing large multidisciplinary problems into several multidisciplinary analysis subsystems (MDASS) and processing it in parallel. This paper proposes new strategy for parallel decomposition of multidisciplinary problems to improve design efficiency by using the multiple objective genetic algorithm (MOGA), and a sample test case is presented to show the effects of optimizing the sequence with MOGA.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.10a
• /
• pp.54-58
• /
• 1997

In this study, study, about Automatic Loader and Unloader system which can directly be used for material handing and tool operating is moving linear transfer system for mainly forming of small electronic unit and other at press line. This system for been installed in a press in order to load and unload a workpiece from a press die. Control method be used Programmable logic control(PLC) unit. other Control equipment of system is Motor drive, Positioning Control and so on. It took data of input from each sensor and send signal of output to actuator by sequence program. We try to Characteristics test of this system has good condition when operating by laser measurement

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.5
• /
• pp.144-149
• /
• 2000

The demands for robotic and automatic system are continually increasing in manufacturing fields. There have been many studies to monitor and predict the system, but they have mainly focused upon measuring cutting force, and current of motor spindle, and upon using acoustic sensor, etc. In this study, time series sequence of cutting force was acquired by taking advantage of piezoelectric type tool dynamometer. Radial cutting force was obtained from it and was available for useful observation data. The parameter was estimated using PAA(parameter adaptation algorithm) from observation data. ARMA(auto regressive moving average) model was selected for system model and second order was decided according to parameter estimation. Uncorrelation test was also carried out to verify convergence of parameter.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.4
• /
• pp.1-6
• /
• 2002

In order to simulate the actual wet-end process in papermachine, RDA, a novel handsheet former, was used and following results were obtained. While the addition of polyelectrolytes gives significant effect on fiber flocculation, increase of stock consistency influenced on the formation of RDA sheets greatly. In particular, the consistency increase from 0.3 % to 0.4% abruptly increased floe size of RDA sheet and it results in severe deterioration of paper strength. Stock consistency, therefore, should be regarded as the most important factor in the formation simulation with RDA and should be controlled as the first sequence of tuning the operating conditions of RDA to simulate correctly the target machine paper's formation.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.197-200
• /
• 2005

Super resolution image reconstruction method refers to image processing algorithms that produce a high resolution(HR) image from observed several low resolution(LR) images of the same scene. This method is proved to be useful in many practical cases where multiple frames of the same scene can be obtained, such as satellite imaging, video surveillance, video enhancement and restoration, digital mosaicking, and medical imaging. In this paper we applied super resolution reconstruction method in spatial domain to video sequences. Test images are adjacently sampled images from continuous video sequences and overlapped for high rate. We constructed the observation model between the HR images and LR images applied by the Maximum A Posteriori(MAP) reconstruction method that is one of the major methods in the super resolution grid construction. Based on this method, we reconstructed high resolution images from low resolution images and compared the results with those from other known interpolation methods.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1191-1192
• /
• 2011

We released new triple redundant digital excitation system with real time generator-turbine simulator. One of its great merits is the real time generator-turbine simulator when it was compared with the other products. If excitation system is tripped by unexpected faults, Maintenance man can do easily performance test of digital excitation control board, sequence relay and thyristor switching device of phase controlled rectifier without manufacturer's support. For the verification of this system, It was tested with an actual excitation system implemented on 5kVA M-G Set. After finishing the tests, the trial product will be installed and operated at a 500MW thermal power plant.

• Journal of the Korean Society of Safety
• /
• v.16 no.1
• /
• pp.9-17
• /
• 2001

The purpose of this research is to analyze the impact resposes(impulsive stress and strain etc.) of anisotropic materials subjected to the low-velocity impact. For this purpose, a beam finite element program based on modified higher-order beam theory for anisotropic materials are developed and used to simulate the dynamic behaviors [contact force, displacement of ball and target, strain(stress) response histories] according to the changes of material property, stacking sequence, velocity and dimension etc.. Test materials for simulation are composed of $[0^{\circ}/45^{\circ}/0^{\circ}/-45^{\circ}/0^{\circ}]_{2s} and [90^{\circ}/45^{\circ}/90^{\circ}/-45^{\circ}/90^{\circ}]_{2s}$ stacking sequences. Finally, the results of this simulation are compared with those of wave propagation theory and then the impact responses and wave propagation phenomena are investigated.