• Journal of the Korean institute of surface engineering
• /
• v.34 no.5
• /
• pp.435-444
• /
• 2001

WC-( $Ti_{1-x}$ A $l_{x}$) N coatings of constant changing Al concentration were deposited on S45C substrates by high-ionization sputtered PVD method. The Al concentration could be controlled by using evaporation source for Al and fixing the evaporation rate of the metals (i.e, WC- $Ti_{0.86}$A $l_{0.14}$N, WC- $Ti_{0.72}$A $l_{0.28}$N, and WC- $Ti_{0.58}$A $l_{0.42}$N). The corrosion behavior of WC-( $Ti_{1-x}$ A $l_{x}$)N coatings in a deaerated 3.5% NaCl solution was investigated by electrochemical corrosion tests and surface analyses. The measured galvanic corrosion currents between coating and substrate indicated that WC- $Ti_{0.72}$A $l_{0.28}$N coating showed the best resistance of the coating tested. The results of potentiodynamic polarization tests showed that the WC- $Ti_{0.72}$A $l_{0.28}$N coating deposited with 32W/c $m^2$ of Al target revealed higher corrosion resistance. This indicated that the WC- $Ti_{0.72}$A $l_{0.28}$N coating is effective in improving corrosion resistance. In EIS, the WC- $Ti_{0.72}$A $l_{0.28}$N coating showed one time constant loop and increased a polarization resistance of coating ( $R_{coat}$) relative to other samples. Compositional variations of WC-( $Ti_{1-x}$ A $l_{x}$)N coatings were analyzed by EDS and XRD analysis was performed to evaluate the crystal structure and compounds formation behavior. Surface morphologies of the films were observed using SEM and AFM. Scratch test was performed to measure film adhesion strength.strength. adhesion strength.strength.

• Archives of Plastic Surgery
• /
• v.50 no.6
• /
• pp.578-585
• /
• 2023

An artificial sphincter implanted in the bulbous urethra to treat severe postprostatectomy urinary incontinence is effective, but embedding-associated complications can occur. We assessed the feasibility, efficacy, and safety of urethral graciloplasty cross-innervated by the pudendal nerve. A simulation surgery on three male fresh cadavers was performed. Both ends of the gracilis muscle were isolated only on its vascular pedicle with proximal end of the obturator nerve severed and transferred to the perineum. We examined whether the gracilis muscle could be wrapped around the bulbous urethra and whether the obturator nerve was long enough to suture with the pudendal nerve. In addition, surgery was performed on a 71-year-old male patient with severe urinary incontinence. The postoperative 12-month outcomes were assessed using a 24-hour pad test and urodynamic study. In all cadaveric simulations, the gracilis muscles could be wrapped around the bulbous urethra in a γ-loop configuration. The length of the obturator nerve was sufficient for neurorrhaphy with the pudendal nerve. In the clinical case, the postoperative course was uneventful. The mean maximum urethral closure pressure and functional profile length increased from 40.7 to 70 cm H₂O and from 40.1 to 45.3 mm, respectively. Although urinary incontinence was not completely cured, the patient was able to maintain urinary continence at night. Urethral graciloplasty cross-innervated by the pudendal nerve is effective in raising the urethral pressure and reducing urinary incontinence.

• Journal of Bio-Environment Control
• /
• v.26 no.1
• /
• pp.7-12
• /
• 2017

This experiment was conducted to analyze the effect of drainage reuse rate on the growth and fruiting of summer paprika in closed hydroponic cultivation. The experiment was carried out for 25 weeks from March to September 2015 with 0, 20, 30, 50% mixing ratio of waste nutrient solution using non - recycling hydroponic cultivation as a control. As a result, stem diameter of the test was different in the groups 1 and 2, but no difference showed as the group progressed more than 3 groups. L.A.I tended to decrease with increasing drainage mixing ratio. The number of nodes in the 50% reuse test group was 1.4 compared to the control group, but there was no significant difference. The number of harvested nodes was significantly different in the control group (11.1 nodes) and the 50% reuse test group (8.7 nodes), and the harvested nodes tended to decrease as the drainage was reused. The ratio of harvest was also the same as that of the harvesting node, and the control was the highest at 33.2% and the lowest at the 50% reuse test at 27.6%. Relative yields were reduced by 30%, 35% and 45% in the control group in the first group, and this tendency was also observed in the second and fourth groups. However, in the 3 and 5 groups, the production of 50% test group increased by 13% and 5%. The ratio of unmarketable fruit was increased 2%, 4%, 4%, and 7% in 0%, 20%, 30% and 50% reuse test, respectively. In conclusion, if the decrease in yield due to the decline in early growth is carefully managed, even if the imbalance of inorganic ions occurs after the mid-term growth, the growth of the crop will enter into a stable period and the re-use will not be worried about the growth and the yield decrease.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.4
• /
• pp.369-374
• /
• 2015

In this paper, an EM sensing based prestressing force estimation method is proposed, in which it can estimate tensile force of PS tendon for PSC girder. The PSC girder has more improved performance than the general concrete girder by introducing the prestressing to the concrete. Thus the PSC girder bridge is widely constructed due to its high performance and low cost. However, the prestressing force has not been managed nevertheless it is major factor for the maintenance of the PSC girder bridge. The prestressing force was just measured during construction using jacking device and after that, it can not be managed. For this reason, this paper proposes a tensile force estimation method of PS tendon based on EM sensor. The permeability of ferroelectric material is changed according to the induced stress to the material, in which it can be measured using EM sensor. To measure the permeability of PS tendon, the EM sensor was fabricated and verified by performing the MTS test. The test was performed using 7-wire steel tendon under the 0, 40, 80, 120, 160, 200 KN of tensile force. The permeability of PS tendon was gradually decreased according to the increasement of tensile force. The regression method was used to find the relation between permeability and stress. As a result, the permeability has linear relation with the tensile force of PS tendon and the pre-stressing force can be estimated by the derived estimation equation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.219-225
• /
• 2020

In this study, the prototype of a blower was designed and made to develop a long-life blower with a volume flow rate of 10,000 ㎥/min with a required total pressure efficiency of 83% or more. Five experimental impellers with various lengths of dust deflectors were manufactured and used for the erosion experiments. The erosion test was conducted by operating for 160 hours in a self-produced closed loop-type erosion test apparatus. A prototype of a model blower was designed, fabricated, and tested. The results revealed a total pressure, air volume flow rate, and efficiency of 690.6 mmAq, 16,243.6 ㎥/min, and 83.6%, respectively, as the result of conversion to a blower based on the measured value of the blower model. The prototype was designed and fabricated as the experimental erosion equipment of the blower. A blower with a dust deflector was developed by performing the erosion experiments under harsh conditions. The blower showed an improved effect of more than 190% based on the wear thickness of the impeller compared to a conventional blower without a dust deflector.

• Journal of Digital Convergence
• /
• v.15 no.10
• /
• pp.455-465
• /
• 2017

This study focuses on design development and verification through virtual simulation based on 3D model data in the cloud platform as a method of utilization of engineering technology of design in the fourth industrial revolution era. The goal of research is to develop and examine a design for the needs of the target that has never been met before through virtual simulations that can be conducted in practice. As a research method, we analyzed secondary data to identify the needs of the target, and did literature research for the ergonomic data and target body development stages. In addition, the design development process of this study was shown meaningful result in design, structure, safety, material, durability through loop test of 7 virtual simulations. This study can be applied to the automated process system based on 3D model data in the 4th industrial revolution era and can be used as an element of the cyber physics system for the additional research.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.3
• /
• pp.165-172
• /
• 2016

An experimental study of the thermal-hydraulic characteristics of passive safety systems (PSSs) was conducted using a system-integrated modular advanced reactor-integral test loop (SMART-ITL). The present passive safety injection system for the SMART-ITL consists of one train with the core makeup tank (CMT), the safety injection tank, and the automatic depressurization system. The objective of this study is to investigate the injection effect of the PSS on the small-break loss-of-coolant accident (SBLOCA) scenario for a 0.4 inch line break in the safety-injection system (SIS). The steady-state condition was maintained for 746 seconds before the break. When the major parameters of the target value and test results were compared, most of the thermal-hydraulic parameters agreed closely with each other. The water level of the reactor pressure vessel (RPV) was maintained higher than that of the fuel assembly plate during the transient, for the present CMT and safety injection tank (SIT) flow rate conditions. It can be seen that the capability of an emergency core cooling system is sufficient during the transient with SMART passive SISs.

• Journal of Music and Human Behavior
• /
• v.12 no.1
• /
• pp.1-21
• /
• 2015

This study examined the effects of a tablet PC-based music-making program on the executive function of adolescents with intellectual disabilities. Four adolescents with intellectual disabilities participated in this program. Each participant received 45-minute individual sessions twice a week for a total of 16 sessions. The music-making program was designed in the sequence of planning; learning table PC operations; exploring musical elements; making rhythm, melody, and lyrics; composing loop sections; and presentation of the completed music. The Stroop test, Children's Color Trails Test, and Digit Span and Letter-Number sequencing tests were measured at pretest, midtest, and posttest in order to examine changes in executive function. The participants showed increased scores on all three tests. The participants' attention span also increased and their attempts to correct errors during tasks occurred more frequently at posttest. This study supports the effects of the technology-based program on the executive function of adolescents with intellectual disabilities and presents its expanded applicability for adolescents who show low cognitive function and limited motivation for cognitive engagement.

• Journal of Fisheries and Marine Sciences Education
• /
• v.5 no.1
• /
• pp.31-44
• /
• 1993

Through the early 1900's, the evolution of the surface condenser was closely tied to the development of steam engine and the turbine. As the chemical and petroleum industries evolved in the 1900's, the use of surface condensers in many different processes. Today, industry uses condensers in many shapes and sizes. The actual condensation process occurs on the outside surface of tubes. The nature of this surface geometry affects the condenser's heat transfer performance. The first condensers were built with plain tubes. As tube manufacturing techniques advanced, manufacturers started making tubes with integral fins. In the 1940's, fin densities were limited to about 600 to 700 fins per meter(fpm) because of manufacturing procedure. Today new manufacturing techniques allow production of tubes with fin densities ranging from 750 to 1600 fpm. The integral-fin tubes investigated in this paper are nominally 19 mm diameter. Eight tubes have been used with trapezodially shaped integral-fins having fin density from 748 to 1654 fpm and 10, 30 grooves. For comparison, tests are made using a plain tube having the same inside diameter and an outside diameter equal to that at the root of the fins for the finned tubes. Betty and Katz's theoretical modelis is used to predict the R-11 condensation coefficient on horizontal integral-fin tubes having 748, 1024 and 1299 fpm. Experiments are carried out using R-11 as working fluid. The refrigerant condensates at a saturation state of $30^{\circ}C$ on the outside tube surface cooled by coolant. The amount of noncondensable gases present in the test loop is reduced to a negligible value by repeated purging. For a given heat input to the boiler and given cooling water flow rate, all test data are taken at steady state. The observed heat transfer enhancement for the finned and grooved tubes significantly exceeded that to be expected on grounds of increased area. For the eight fin tubes and one plain tube tested, the best performance has been obtained with a tube having a fin density of 1299 fpm, and a fin bight of 1.2mm and 30 grooves.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.431-432
• /
• 2012

In the era of 20 nm scaled semiconductor volume manufacturing, Microelectronics Manufacturing Engineering Education is presented in this paper. The purpose of microelectronic engineering education is to educate engineers to work in the semiconductor industry; it is therefore should be considered even before than technology development. Three Microelectronics Manufacturing Engineering related courses are introduced, and how undergraduate students acquired hands-on experience on Microelectronics fabrication and manufacturing. Conventionally employed wire bonding was recognized as not only an additional parasitic source in high-frequency mobile applications due to the increased inductance caused from the wiring loop, but also a huddle for minimizing IC packaging footprint. To alleviate the concerns, chip bumping technologies such as flip chip bumping and pillar bumping have been suggested as promising chip assembly methods to provide high-density interconnects and lower signal propagation delay [1,2]. Aluminum as metal interconnecting material over the decades in integrated circuits (ICs) manufacturing has been rapidly replaced with copper in majority IC products. A single copper metal layer with various test patterns of lines and vias and $400{\mu}m$ by $400{\mu}m$ interconnected pads are formed. Mask M1 allows metal interconnection patterns on 4" wafers with AZ1512 positive tone photoresist, and Cu/TiN/Ti layers are wet etched in two steps. We employed WPR, a thick patternable negative photoresist, manufactured by JSR Corp., which is specifically developed as dielectric material for multi- chip packaging (MCP) and package-on-package (PoP). Spin-coating at 1,000 rpm, i-line UV exposure, and 1 hour curing at $110^{\circ}C$ allows about $25{\mu}m$ thick passivation layer before performing wafer level soldering. Conventional Si3N4 passivation between Cu and WPR layer using plasma CVD can be an optional. To practice the board level flip chip assembly, individual students draw their own fan-outs of 40 rectangle pads using Eagle CAD, a free PCB artwork EDA. Individuals then transfer the test circuitry on a blank CCFL board followed by Cu etching and solder mask processes. Negative dry film resist (DFR), Accimage$^{(R)}$, manufactured by Kolon Industries, Inc., was used for solder resist for ball grid array (BGA). We demonstrated how Microelectronics Manufacturing Engineering education has been performed by presenting brief intermediate by-product from undergraduate and graduate students. Microelectronics Manufacturing Engineering, once again, is to educating engineers to actively work in the area of semiconductor manufacturing. Through one semester senior level hands-on laboratory course, participating students will have clearer understanding on microelectronics manufacturing and realized the importance of manufacturing yield in practice.