• The Journal of Korean Academy of Prosthodontics
• /
• v.42 no.5
• /
• pp.597-607
• /
• 2004

Purpose: This study was peformed to investigate the retrievability of the cemented crown from the cementation type implant abutment. Material and method: The cementation type implant abutments (NEOBIOTECH implant abutment regular, 3 degree taper, 10mm length, 4mm diameter, Ti grade III, machined surface. Hwasung, Kyunggi-do) and cemented crowns were divided into 3 groups, depending on their hole angles formed in the crowns for their retrievability. The abutments and crowns were luted with 4 kinds of cements and separation test using metal wedge was executed with Instron 4465 Universal Testing Machine and the maximum impact force of the modified crown ejector was measured. Results and conclusion : 1. All of the cementation type implant abutments and cemented crowns were separated with relatively small force by metal wedge. 2. The retrieving force was minimum when the metal wedge was applied perpendicular to the axis of abutment. 3. The force for retrieving crowns from abutments was maximum in resin cement group, and reduced in orders of zinc phosphate cement, glass ionomer cement and zinc oxide eugenol cement. 4. The maximum force obtained by the crown ejector was higher than the retrieval force in ZOE and GI cement and lower than that in ZPC and resin cement. 5. If it has similar conditions clinically, the cemented crowns luted with 2 types of cements (ZOE, GI cement) can be safely retrieved from the cementation type implant abutments by the modified crown ejector.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.7
• /
• pp.7-15
• /
• 2020

Recently, the fourth industrial revolution has been presented as a new paradigm and additive manufacturing (AM) has become one of the most important topics. For this reason, process monitoring for each cross-sectional layer of additive metal manufacturing is important. Particularly, deep learning can train a machine to analyze, optimize, and repair defects. In this paper, image classification is proposed by learning images of defects in the metal cross sections using the convolution neural network (CNN) image labeling algorithm. Defects were classified into three categories: crack, porosity, and hole. To overcome a lack-of-data problem, the amount of learning data was augmented using a data augmentation algorithm. This augmentation algorithm can transform an image to 180 images, increasing the learning accuracy. The number of training and validation images was 25,920 (80 %) and 6,480 (20 %), respectively. An optimized case with a combination of fully connected layers, an optimizer, and a loss function, showed that the model accuracy was 99.7 % and had a success rate of 97.8 % for 180 test images. In conclusion, image labeling was successfully performed and it is expected to be applied to automated AM process inspection and repair systems in the future.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.12
• /
• pp.1151-1159
• /
• 2012

Spray visualization and computer simulation of a DME injector have been conducted to investigate the enlarged injection hole diameter effect. To increase the reliability of the computational result, simulation results have been compared with the visualization test results, and the behaviors of a DME spray under various high-pressure and -temperature conditions have been computed. This study shows a discrepancy of 3.57% between the experimental and the computational results of penetration length for an injection pressure of 35 MPa and ambient pressure of 5 MPa. When simulating the engine conditions, the maximum penetration length of a fully developed DME spray is 42 mm when the temperature to pressure ratio is 300 K/MPa. The DME spray behavior is dominantly affected by the ambient pressure under the condition that the ratio is less than 300 K/MPa, and by the ambient temperature under the condition that the ratio is more than 300 K/MPa.

• Tunnel and Underground Space
• /
• v.23 no.2
• /
• pp.99-109
• /
• 2013

The slopes of open-pit mine are typically designed without considering the reinforcement and support method due to the economical efficiency. However, the long-term stability of final pit slope is needed in some case, therefore the appropriate measures that can improve the stability are required. In this study, the field survey and laboratory test were carried out in S limestone mine. The stability assessment of final pit slope was performed through the stereographic projection method, SMR, and numerical analysis. And countermeasures for stabilization were proposed. The results of analysis show that full scale of slope failure is not expected but the failures of bench slope scale are likely to occur. In oder to increase the stability of bench slope, we suggested the remedial methods as follows: excavating the final pit slope by pre-splitting blasting, placing the wide berm in the intermediate bench slope and installing the horizontal drainage hole in the place of local ground water runoff.

• Proceedings of the Korean Society of Applied Pharmacology
• /
• 2008.04a
• /
• pp.119-142
• /
• 2008

Zizyphi Spinosi Semen (ZSS) has been widely used for the treatment of anxiety and insomnia in Korea and China. This experiment was performed to know whether sanjoinine A, one of major alkaloid compounds of ZSS has anxiolytic and hypnotic effects through the GABAergic systems. Our results showed that administration of sanjoinine A increased open arm entries and spent time in open arm in the elevated plus-maze and increased head dips in hole board test. Different from traditional anxiolytic, diazepam, sanjoinine A itself did not decrease locomotor activity and strength level in mice. Furthermore, Sanjoinine A (0.5-2.0 mg/kg) prolonged sleeping time and reduced sleeping latency induced by pentobarbital in a dose-dependent manner similar to muscimol, a $GABA_A$ receptor agonist. Sanjoinine A (0.25-1.0 mg/kg) also increased sleeping rate and sleeping time in the combined administration at the sub-hypnotic dose of pentobarbital and showed synergic effects with muscimol in potentiating sleeping onset and enhancing sleeping time induced by pentobarbital. However, sanjoinine A itself did not induce sleeping at the higher dose. In addition, both of sanjoinine A and pentobarbital increased chloride influx in primary cultured cerebellar granule cells. Sanjoinine A decreased the $GABA_A$ receptor ${\alpha}$-subunit expression and increased ${\gamma}$-subunit expression, and had no effects on abundance of ${\beta}$-subunit in primary cultured cerebellar granule cells, showing different expression of subunits from pentobarbital. In conclusion, sanjoinine A shows anxiolytic-like effects and augments pentabarbital-induced sleeping behaviors through the modification of GABAergic systems. [This work was supported by the Korea Research Foundation Grant funded by the Korean Government (MOEHRD) (The Regional Research Universities Program/Center for Healthcare Technology Development)].

• Journal of the Korean Society for Nondestructive Testing
• /
• v.13 no.3
• /
• pp.24-30
• /
• 1993

The necessity of ultrasonic inspection to detect the cracks in turbine blade is being increased as the forced outage of nuclear power plants have been occurred due to blade failure in turbine components. However, the complex blade root geometry causes the ultrasonic inspection technique not to be established yet and much effort is required to set up a more reliable inspection. In this paper, the ultrasonic inspection technique for flaw detectability, skew angle effect, identification of flaw and geometric signal have been investigated with a test block and discussed the interpretation of ultrasonic signal through the acquisition and analysis of RF waveform. The experimental results show that the proper examination procedure can be established. It is required that the skew angle is essential to decrease the effect of signals from the complex blade geometry. The present results of this study can be applied to the site inspection without blade disassembly.

• Steel and Composite Structures
• /
• v.1 no.1
• /
• pp.17-32
• /
• 2001

The Rosette-joining system is a completely new press-joining method for cold-formed steel structures. One Rosette-joint has a shear capacity equal to that of approximately four screws or rivets. The Rosette thin-walled steel truss system presents a new fully integrated prefabricated alternative to light-weight roof truss structures. The trusses are built up on special industrial production lines from modified top hat sections used as top and bottom chords and channel sections used as webs which are joined together with the Rosette press-joining technique to form a completed structure easy to transport and install. A single web section is used when sufficient but can be strengthened by double-nesting two separate sections or by using two lateral profiles where greater compressive axial forces are met. An individual joint in the truss can be strengthened by introducing a hollow bolt into the joint hole. The bolt gives the connection capacity a boost of approximately 20%. A series of laboratory tests have been carried out in order to verify the Rosette truss system in practice. In addition to compression tests on individual sections of different lengths, tests have also been done on small structural assemblies and on actual full-scale trusses of a span of 10 metres. Design calculations have been performed on selected roof truss geometries based on the test results, FE-analysis and on the Eurocode 3 and U.S.(AISI) design codes.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.2
• /
• pp.93-102
• /
• 1995

A series of test was performed by measuring the failure strength and the failure mode of fiber reinforced composite laminates joint containing two holes in Series or Parallel. $[0^{\circ}/45^{\circ}/90^{\circ}/-45^{\circ}]_s$ laminate with W/d(Side distance ratio) 4.0 and E/d(Edge distance ratio) 3.0 has the full bearing strength and are preferable in case of the good efficiency in two series hole. Comparisons were made between testing results and predicting values of the FEM model. Good agreements were fecund between them except the case of $E/d=2{\sim}3$. In the case of $G_h{\geq}3.0d$ and $G_v{\geq}3.0d$ since the interaction coefficients between two parallel holes and between two series holes were small, holes can be treated as independent. The Acoustic Emission(AE) and SEM method were utilized to find out the initial defects, damage and the fracture mechanism.

• The Research Journal of the Costume Culture
• /
• v.18 no.5
• /
• pp.892-907
• /
• 2010

The purpose of this study was to compare torso pattern made by draping and flat pattern method in terms of the size of breast. The size of this study was classified as 75A and 75D according to the size of breast. Each torso pattern by the combination of the size and pattern method was compared and analyzed. In order to test the fit of the draping and flat pattern that was developed according to the size of breast, the outer appearance was evaluated. The results of the study were as follows: First, The most striking size difference was difference between the front and the back on bust line level, which decides on position of the side seam in comparison of size between draping and flat pattern of 75A and 75D. In the flat pattern, the difference between the front and the back in the size of breast was consistent regardless of a change in the size of breast. However, in the draping, the bigger breast led to the bigger difference between the front and the back on bustline level. Second, the flat pattern in 75D was evaluated to be the worst in 27 items among total 46 items for the evaluation of outer appearance in the draping and flat pattern of 75A and 75D. Third, regardless of size, the draping was evaluated to be more suitable in the areas related to neck, arm hole, and waist dart than the flat pattern. These results are suggesting that the draping is a method of reflecting characteristic of the body type more accurately than the flat pattern, and that the draping is a more suitable method than the flat pattern for the design of clothing pattern of the body type with big breast like 75D.

• The Korean Journal of Pharmacology
• /
• v.11 no.1 s.17
• /
• pp.55-60
• /
• 1975

An animal which is placed in a new environment displays a complex behavioral pattern consisting of locomotion, grooming and rearing. This behavioral pattern is influenced by endogenous and exogenous stimuli, such as hormonal secretion, level of neurohumoral transmitters, drugs and light. It is widely known that the most tranquilizers depressed spontaneous motor activity although their mechanisms of action were different, while antidepressants stimulated except imipramine which showed various action. Until the present time, the hole-board apparatus, which gives rather subjective data, has been used extensively to study the effects of drugs on general activity and exploratory behavior in mice. Recently a new apparatus for mobility measurements, called a 'Selective Activity Meter' has been introduced. This instrument supposedly produces more objective data on activity and behavior. The purpose of the present experiment was to study the influence of psychotropics on motor activity using the Selective Activity Meter. In the experiment, various psychotropic agents such as major tranquilizers(chlorpromazine, haloperidol); minor tranquilizers(meprobamate, diazepam); and antidepressants(amphetamine, imipramine) were used. In each experiment, the drug was administered to five mice and their activity was recorded. Each experiment was run five or more times and the results are based on the mean of each trial. The results are summarized as follows: 1. The group of mice treated with chlorpromazine showed markedly inhibited motor activity in comparison with controls and the inhibitory action of chlorpromazine was shown to be more intense than any of the other drugs used in the test. Haloperidol administration yielded similar results until 60 minutes, but mice showed less inhibition of motor activity than with chlorpromazine after 90 minutes. 2. In the group treated with diazepam, there was strong inhibition of motor activity until 30 minutes, but after 60 minutes the mice showed less inhibition than with chlorpromazine. In the meprobamate group, motor activity was inhibited in a manner similar to that of other tranquilizers, but the inhibition was less than that of diazepam. 3. In the group treated with imipramine, the inhibition developed gradually after ten minutes. 4. The effects of amphetamine did not appear until 30 minutes after administration, but then there was a significant increase in the motor activity.