• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.10a
• /
• pp.551-561
• /
• 2006

Incheon bridge project is to construct total 12km long bridges on the sea consist of 800m span length cable stayed bridge, approach bridge and viaduct bridge based on LRFD design specification. To design pile foundations by RCD of each bridge unit, total 4 number of preliminary full scale pile load tests with Osterberg cell method were carried out on the piles for testing. The test load was planned to more than the expected design ultimate capacity and about 29,000tons maximum load was recorded. From the interpretation of test results, design parameters are evaluated and applied to the design. Preliminary pile load test plan and detailed execution of pile load tests are introduced and summarized. The resistance factors are presented for pile design of Incheon Bridge Project in LRFD considering variation of ground conditions and number of test piles.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.1169-1172
• /
• 1998

We designed an ALU(Airthmetic Logic Unit) with BIST(Built-In Self Test), which is suitable for 32-bit DSP RISC processors. We minimized the area of this ALU by allowing different operations to share several hardware blocks. Moreover, we applied DFT(Design for Testability) to ALU and offered Bist(Built-In Self-Test) function. BIST is composed of pattern generation and response analysis. We used the reseeding method and testability design for the high fault coverage. These techniques reduce the test length. Chip's reliability is improved by testing and the cost of testing system can be reduced.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.1
• /
• pp.147-153
• /
• 2001

This paper proposes a shaker system design for acceleration test of gimbal. Main reason of shaker system design is to give acceleration to the gimbal, which is moving and tracking the target on the tracking test equipment. The shaker system is mounted on the tracking test equipment. It uses the scotch yoke mechanism to have the constant movement in return. The Scotch yoke mechanism changes the rotational movement of constant velocity to simple harmonic motion.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.551-553
• /
• 2002

The cubicle type GIS rated at 25.8kV has been designed and manufactured by Jinkwang E&C eacently with their own technologies and KERI's assistances. The C-GIS has been tested to check the design capability for reference before conducting the type test. The operating characteristics test, short time withstand current and peak withstand current test, basic short circuit test duty T60 for preconditioning test, cable charging current switching test, capacitor bank current switching test, basic short circuit test duty T100s and T100a, single phase earth fault test, double earth fault test has been conducted. The test results show that the design and the manufacturing of the C-GIS has an enough capability to pass through the type test except the occurrence of 2 NSDDs in the cable charging current switching test and the instability of opening time at the minimum operating voltage. The problems shown in the tests will be improved soon and the successful pass will be expected in the following type test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.73-79
• /
• 1998

For the design and development of the wheel type excavator, the dynamic effects of travelling on the performance of the equipment should be first analyzed and conside- red in the initial design stage. In order to test the durability of the equipment in a short period, th travelling test should be performed over accelerated durability test tracks. which is more severe than general field roads such as city road, paved road, unpaved road and rough road. In this paper, a parametric study is performed in order to determine important design parameters of durability test track of a wheel type excavator. A rigid body model is developed using DADS and dynamic analysis is performed for the equipment travelling over several test roads with different severity. A comparison of test and analysis results is also presented.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.32-44
• /
• 2002

This paper contains the information that describes the test fixture design and technology for full-scale airframe static test. Obtained technologies consist of determination of design load for test fixture, design technique for loading system, counterbalance system, positioning system of test article, test equipment and overload protection method. Full-scale airframe static test of advanced jet trainer was implemented using test fixture which are applied these technique.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.3
• /
• pp.154-160
• /
• 2007

A direction finding system test-bed(DFSTB) at the electronic warfare communication-band is presented to efficiently evaluate and optimize the performance of the direction finding system through the indoor test setup. This test-bed gives a significant benefit to the designers of the direction finding system because it allows flexible test and design trade-off in the system design cycle. The system description and implementation of test-bed architecture, and the experiment results of direction finding accuracy according to modulation schemes are presented.

• Journal of Applied Reliability
• /
• v.18 no.2
• /
• pp.95-103
• /
• 2018

Purpose: Environment test aim to validate the guarantee of required capability of materiel against various environment conditions which exposed during materiel life-cycle. In this paper, environment test design procedure and tailoring guideline for Korean peninsula and periphery climate are proposed. Methods: To design tailoring guideline, climate data which are regarding Korean peninsula and periphery regions provided from Korea Meteorological Administration (KMA) and National Climatic Data Center (NCDC) are used. Conclusion: For effective environment test, it is important that environment test have to design in considering environment conditions during materiel life-cycle. It is concluded that the high temperature test level can be softer than the test criteria in MIL-HDBK-310, however, the low temperature test level will be expected to be $2{\sim}6^{\circ}C$ harsher than MIL-HDBK-310.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.126-131
• /
• 2007

Design for automatic coupler system of Korean Tilting Train eXpress is described. In order to carry out validation & verification activities for system design, test condition is taken into account at collision speed of 10km/h, which is required in Safety Notice for rolling stock vehicle. The study aims at safety validation between a coupler and car body including design verification for a coupler through the identifying of system design and the evaluating of test results.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.41 no.5
• /
• pp.950-965
• /
• 2017

This present study proposed a newly developed test method to evaluate the dexterity and mobility of a firefighter's protective gloves. The first step evaluated the mobility and dexterity of the current type of fire protective gloves and three new types of protective gloves using Don-doff test, ASTM dexterity, Minnesota dexterity, Bennett hand tool test, and ASTM torque test. Three firefighters ($47.3{\pm}5.0yr$ in age, $178.6{\pm}2.9cm$ in height) participated in a series of experiments. The second step was to design and suggest an integrated test method based on the results of the first experiment. As a result of the first experiment, we concluded that 1) the mobility and dexterity tests for firefighting gloves should include both wet and dry tests, 2) The three kinds of dexterity tests could be integrated into one test, and 3) The don-doff test and the torque test should be independent from the newly developed integrated test. In summary, we suggested a simplified test method that combined ASTM dexterity, Minnesota dexterity, and Bennett hand tool test. The integrated system can reduce total time spent on dexterity tests and improve the validity of the test in terms of firefighters' manual work.