• Nuclear Engineering and Technology
• /
• v.32 no.1
• /
• pp.57-66
• /
• 2000

The RELAP5 code has been developed for best-estimate simulation of transients and accidents for pressurized water reactors and their associated systems, but it has not been fully assessed for those of CANDU reactors. However, a previous study suggested that the RELAP5 code could be applicable to simulate the transients and accidents for CANDU reactors. Nevertheless, it is indicated that there are some works to be resolved, such as modeling of headers and multi-channel simulation for the reactor core, etc. Therefore, this study has been initiated with an aim to identify the code applicability for all the postulated transients and accidents in CANDU reactors. In the present study, the small inlet header break experiment (B8604) in the RD-14 test facility was simulated with RELAP5/MOD3.2 code. The RELAP5 results were also compared with both experimental data and those of CATHENA analyses performed by AECL and the analyses demonstrated the code's capability to predict major . phenomena occurring in the transient with sufficient accuracy for both Qualitative and quantitative viewpoint However, some discrepancies in the depressurization of the primary heat transport system after the break and the consequent time delay of the major phenomena were also observed.

• Journal of Industrial Technology
• /
• v.43 no.1
• /
• pp.7-13
• /
• 2023

Nowadays, traffic congestion is emerging as a major problem due to the rapid population growth and the increase in automobiles. The train is a convenient means of transportation that can efficiently solve these problems. Trains have been developed in line with human aspirations for a long time, but research on safety is still insufficient. This study aims to check safety by conducting static tests and fatigue tests on bogie frames, and to help develop bogie frames in the future. For the static test, a strain gauge was attached to the point where the local stress concentration was expected beforehand, and the result value was derived, compared with existing theories, and expressed as a Goodman diagram. In the fatigue test, a total of 10 million loads were applied over three stages, and no cracks appeared in the non-destructive test conducted after each stage. Both tests were conducted according to the strict test method of the bogie frame presented by the UIC Code. It satisfied both fatigue life and strength evaluation criteria and was judged to be a bogie frame usable for safe train production.

• Journal of KIISE:Computing Practices and Letters
• /
• v.15 no.2
• /
• pp.140-144
• /
• 2009

The efficient test tool is indispensable to the test driven development. The test tool is very helpful to get the advantage of the test driven development. Many traditional automation test tool does not support standard script language and are not suitable to unit test. In traditional unit test tool, a code for the test is added at the source code. Such method makes the complexity of a source code and has a problem which must modify many part of the source code when the test case is changed. In this paper, we present a design technique of a flexible unit testing tool which makes a developer can modify easily the test case by using the standard java script in test driven development. We implement the test tool by this design technique to verify the availability of this technique.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.299-302
• /
• 2010

Recently, the malicious code is not easily detectable in the vaccine for the virus, malicious code as a compressed file by modulation pattern is the tendency to delay. Among the many antivirus engines on the market a compressed file that can be modulated by malicious code, and test whether the pattern will need to know. We cover a multi-compressed files, malicious code modulated secreted by examining patterns of test engine is being detected is through a computer simulation. Analysis of secreted activities of malicious code and infect the host file tampering with the system driver files and registry, it gets registered is analyzed. this study will contribute hidden malicious code inspection and enhance vaccine efficacy in reducing the damage caused by malicious code.

• Journal of the Korea Society of Computer and Information
• /
• v.13 no.2
• /
• pp.19-29
• /
• 2008

In case of unit testing, White-box test can be used to closely check source code and to analyze logic and statement errors. On the other hand, in case of function testing of system level, Black-box test can be mainly used to compare actual and expected results by inputting test data because the scale of function is large. This Black-Box test in system testing level has problem in tracing errors in source code when we find errors. Moreover applying White-box test is not easy for system testing level because the levels of test target are different. Therefore this paper suggests the vertical test method of a practical and integrated system level which can checks up to source code level using White-box test style although it aims to test the highly abstract level like a system function. In addition, the experiment explains how to apply the vertical test by displaying an example which traces from UML specification model to the source code and also shows efficiency of error trace.

• Journal of Drive and Control
• /
• v.20 no.3
• /
• pp.9-14
• /
• 2023

In this paper, the selection of a reliable accelerated life test code for a 2-ton forklift was accomplished by choosing the driving resistance coefficient failure-free test time based on a 10,000-hour B₁₀ life. The overall life and average equivalent load of the vehicle were then calculated based on actual driving test conditions using the selected driving resistance coefficient. The gear train's accelerated life test code was selected by adjusting the equivalent load to a torque and rotation speed that did not exceed 125%(about 75HP) of the vehicle rated power. The safety of the test standards was validated by conducting an actual accelerated life test utilizing the proposed test method in this study and comparing the test result with the corresponding theoretical value. It is anticipated that the reliability of the accelerated life test in this paper will be enhanced, by incorporating actual driving performance data collected directly from the forklift and adjusting the conditions used in developing the accelerated life test code.

• Nuclear Engineering and Technology
• /
• v.50 no.6
• /
• pp.981-988
• /
• 2018

An experiment was performed for the OECD/NEA ROSA-2 Project with the large-scale test facility (LSTF), which simulated a steam generator tube rupture (SGTR) accident due to a double-ended guillotine break of one of steam generator (SG) U-tubes with operator recovery actions in a pressurized water reactor. The relief valve of broken SG opened three times after the start of intact SG secondary-side depressurization as the recovery action. Multi-dimensional phenomena specific to the SGTR accident appeared such as significant thermal stratification in a cold leg in broken loop especially during the operation of high-pressure injection (HPI) system. The RELAP5/MOD3.3 code overpredicted the broken SG secondary-side pressure after the start of the intact SG secondary-side depressurization, and failed to calculate the cold leg fluid temperature in broken loop. The combination of the number of the ruptured SG tubes and the HPI system operation difference was found to significantly affect the primary and SG secondary-side pressures through sensitivity analyses with the RELAP5 code.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.1119-1124
• /
• 2008

Defect of the Cable is one of the most frequent cause of fire accident for years. It also take a big part of the fire load for train. In this study, we reviewed the standard code of other countries for cable fire test. Oxygen index, flame propagation test, smoke test and toxicity test codes were investigated. We also suggest the our national code for train cables.

• Journal of Food Hygiene and Safety
• /
• v.20 no.2
• /
• pp.103-113
• /
• 2005

Sanitary codes of retail ffod establishment of Korea, Japan, China, and America were reviewed in order to figure out the differences of the codes. The codes of Korea & Japan are similar in many aspects. The code of America regulates food safety procedures in detail and are easy to interpret. The code of China is broad and not specific in the procedures. Korean code deals with many administration affairs and Japanese code deals with food test and business. Chinese code also deals with administration and standards. American code defines 90 different terms while the codes of rest of the countries define only few terms. For sanitization American code specifies the procedures in specific terms in detail but others do not specify the procedures. For facilities, the American code specifies location, material and procedures but other codes also specify the material but the contents of the codes are not so much specific to compare with American code.

• Nuclear Engineering and Technology
• /
• v.50 no.8
• /
• pp.1412-1420
• /
• 2018

An experiment was performed using the large-scale test facility (LSTF), which simulated a 1% vessel upper head small-break loss-of-coolant accident with an accident management (AM) measure under an assumption of total-failure of high-pressure injection (HPI) system in a pressurized water reactor (PWR). In the LSTF test, liquid level in the upper head affected break flow rate. Coolant was manually injected from the HPI system into cold legs as the AM measure when the maximum core exit temperature reached 623 K. The cladding surface temperature largely increased due to late and slow response of the core exit thermocouples. The AM measure was confirmed to be effective for the core cooling. The RELAP5/MOD3.3 code indicated insufficient prediction of primary coolant distribution. The author conducted uncertainty analysis for the LSTF test employing created phenomena identification and ranking table for each component. The author clarified that peak cladding temperature was largely dependent on the combination of multiple uncertain parameters within the defined uncertain ranges.