• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1465-1469
• /
• 2003

In general satellite verification process, the AOCS (Attitude & Orbit Control Subsystem) should be verified through several kinds of verification test which can be divided into two major category like FBT (Fixed Bed Test) and polarity test. And each test performed in different levels such as ETB (Electrical Test Bed) and satellite level. The test method of FBT is to simulate satellite dynamics with sensors and actuators supported by necessary environmental models in ETB level. The VDS (Vehicle Dynamic Simulator) try to make the real situation as possible as the on-board processor will undergo after launch. The purpose of FBT test is to verify that attitude control logic function and hardware interface is designed as expected with closed loop simulation. The VDS is one of major equipments for performing FBT and consists of software and hardware parts. The VDS operates in VME environments with target board, several commercial boards and custom boards based on the VxWorks real time operating system. In order to make time synchronization between VDS and satellite on-board processor, high reliable semaphore was implemented to make synchronization with the interrupt signal from on-board processor. In this paper, the real-time operating environment used on VDS equipment is introduced, and the hardware and software configurations of VDS summarized in the systematic point of view. Also, we try to figure out the operational concept of VDS and AOCS verification test method with close-loop simulation.

• KIEAE Journal
• /
• 제7권4호
• /
• pp.135-140
• /
• 2007

In this study we settled the trouble of the MgO board of existence by this research. We changed the wooden one of the main ingredient of a board to a perlite and a mineral particle in the aluminum hydroxide group and proceeded with a study to physical character and fire resistance efficiency improvement. The result yellowing phenomenon could be improved and it was possible to reduce size decrease of pin hole and the frequency of occurrence. We found out that the in case of absorbed amount added 5~8% corresponding to the weight decreases the acrylic group emulsion suddenly. So this product is improved with the bending strength and water-resistance. After behavior stop time measurement of a mouse for experiments was measured at the time of a gas harmful effect test, an improved MgO board appeared more highly for an average of 138 seconds compared with a board of existence.

• 마이크로전자및패키징학회지
• /
• 제18권2호
• /
• pp.35-41
• /
• 2011

Recently, board level solder joint reliability performance of IC packages during drop impact becomes a great concern to semiconductor and electronic product manufacturers. The handheld electronic products are prone to being dropped during their useful service life because of their size and weight. The IC packages are susceptible to solder joint failures, induced by a combination of printed circuit board (PCB) bending and mechanical shock during impact. The board level drop testing is an effective method to characterize the solder joint reliability performance of miniature handheld products. In this paper, applying the JEDEC (JESD22-B111) standard present a finite element modeling of the FBGA. The simulation results revealed that maximum stress was located at the outermost solder ball in the PCB or IC package side, which consisted well with the location of crack initiation observed in the failure analysis after drop reliability tests.

• 한국구조물진단유지관리공학회 논문집
• /
• 제9권1호
• /
• pp.119-126
• /
• 2005

본 연구는 H형 및 Channel형 복공판의 정적 하중에 대한 성능을 규명하는데 그 목적이 있다. 보다 향상된 복공판의 성능이 요구되어짐에 따라 보강의 가능성 및 효율성을 파악하였고, 정적재하시험 및 구조해석을 통해 시험체의 개선효과를 비교 검토하였다. 정적재하시험을 통하여 응력과 처짐을 측정하였고, 이를 FEM 해석결과와 비교하였을 때 극한 하중 및 변위, 지간 중앙부와 상 하 플랜지의 휨응력 등에서 H형 복공판은 Channel형 복공판에 비해 약 3배 이상의 높은 강성을 보유하고 있는 것으로 나타났다.

• 수산해양기술연구
• /
• 제58권1호
• /
• pp.85-93
• /
• 2022

In this study, we investigated how satisfaction with on-board training had an effect on career motivation of the trainees. For this purpose, satisfaction for on-board training and career motivation were used as variables. Satisfaction for on-board training were classified into education, environment and operation, and then measurement items were composed. Career motivation consisted of career identity, career insight and career resilience. To establish and test nine hypotheses, a questionnaire survey was conducted by 57 trainees who participated in the Gyeongsang National University on-board sailing training in 2021. To analyze the questionnaire responses, frequency analysis, factor analysis, multiple regression analysis and paired sample t-test were used. As a result of factor analysis, six factors for satisfaction for on-board training were derived. Among the factors, it was analyzed that satisfaction with assignments, the satisfaction with accommodation, and the satisfaction with the adequate condition of facilities and equipment had a significant effect on career motivation. In addition, it was found that career motivation significantly increased through on-board training as a result of comparing the difference between the averages of career motivation before and after on-board training.

• 한국초전도ㆍ저온공학회논문지
• /
• 제13권1호
• /
• pp.12-16
• /
• 2011

In this paper, the prototype of the HTS motor with an on-board cryocooler, is fabricated and tested. The overall system is composed of the stator with conventional copper winding, the rotor with superconductor, and the rotating cryocooler designed from the on-board concept. The rotor is fabricated as the race-track coil with 2G, YBCO tape and contacts with the on-board cryocooler while being rotated together. An inline-type pulse tube refrigerator is used as the on-board cryocooler. The cryocooler is fabricated from optimal process to satisfy the structure and thermal stability of the on-board system. Each component is integrated according to carefully defined sequence. Specially, a combining method of torque tubes is an important part for sustaining stability of the rotor and the cryocooler. In the rotating test, the HTS motor is successfully operated with 240 rpm of rotating speed when 75 A current is supplied to the superconducting rotor. In this paper, potential problems of the HTS motor system using the on-board cryocooler are proposed and solved, and realistic possibility of this concept is also confirmed.

• 수산해양기술연구
• /
• 제30권2호
• /
• pp.71-77
• /
• 1994

A serious of study is carried out to practical use of the three-slot cambered otter board improved by the authors. As the first step, we designed main plates, slots and accessories, such as holding plate, fan-shaped towing plate, normans, center ring, etc. Standing on this design, we made the simple cambered and three-slot cambered model otter board with accessories in a linear scale 6:1. and carried out model test to examine the efficiency of these boards. The obtained results can be summarized as follows: 1. On the simple cambered board with accessories, the values of the maximum shear coefficient($C _{LX}$ ). drag coefficient(($C _{D}$) and hydrodynamic efficiency($C _{L}$/$C _{D}$ ) are 1.39, 0.56, 2.48 at $22^{\circ}$ of the angle of stall respectively. 2. On the three-slot cambered board with accessories, $C _{LX}$/$C _{D}$ and $C _{I}$/$C _{D}$ are 1.67, 0.92, 1.82 at $32^{\circ}$ of the angle of stall respectively. 3.$C _{LX}$ of board with accessories is smaller 10~12% than that of only the main plate, and the angle of stall is almost same. 4. $C _{LX}$ and the angle of stall of the three-slot cambered board with accessories are greater 20% and $10^{\circ}$ than that of the simple cambered board respectively.

• 한국건축시공학회지
• /
• 제16권3호
• /
• pp.193-199
• /
• 2016

본 연구는 산업폐기물로 발생되는 굴 패각과 건식공정 바텀애시를 골재로 활용하여 제작된 내화보드의 가열실험을 통한 성능에 관한 연구이며 다음과 같은 결론을 도출하였다. 전기로 가열실험을 통해 나타난 시험편의 이면온도는 $300^{\circ}C$ 가열상황에서 $103.1{\sim}125.1^{\circ}C$로, $600^{\circ}C$의 가열상황에서 $201.1{\sim}210.1^{\circ}C$로, $900^{\circ}C$의 가열상황에서 $249.2{\sim}276.9^{\circ}C$의 범위로 나타났다. 내화보드 시험편의 경우 일정온도상승 이후 유지되는 것으로 나타나 사용재료들의 경우 내화성능이 발휘되는 것으로 판단된다. 실험의 결과로 유추할 때, 입자의 크기가 작을 경우 $600^{\circ}C$까지는 내화성능이 상대적으로 우수하지만, 그 이상의 온도에서는 입자의 크기가 큰 경우 많은 공극을 포함하여 열전달이 지연되는 것으로 판단된다.

• 대한안전경영과학회지
• /
• 제5권1호
• /
• pp.115-128
• /
• 2003

To comparison the surface treatment methods of stone board materials, the results of Dorry's abrasive test were 23.4 for water-jet system and 18.9 for flame-burner system. Therefore abrasive hardness, the stone board materials by the water-jet system was greater than one by flame-jet system. As a result of Shore's hardness test, the stone board materials by water-jet system was twice greater than one by flame-jet system. Authors carried out microscopic observation to survey a defection of the composition minerals for two methods, but all of the both methods have not founded a defection. Therefore, the stone board materials by water-jet system was greater durability than one by flame-jet for the surface treatment methods.

• 한국철도학회논문집
• /
• 제12권5호
• /
• pp.670-677
• /
• 2009

본 논문은 최고속도 400km/h의 차세대고속열차 차상신호장치의 최고속도시험을 위한 방안을 연구한다. 차세대고속열차 차상신호장치는 열차가 고속선 자동열차제어(ATC)구간과 기존선 자동열차정지(ATS) 및 자동열차방호(ATP)구간을 운행하는 동안 기관사에게 운전정보를 제공하고 기관사실수, 신호장치고장, 천재지변 등으로부터의 열차 안전 확보를 목적으로 한다. 차세대고속열차 최고속도 400km/h 시험은 차상신호장치를 포함한 열차성능 검증을 위한 필수과정으로써, 본 논문에서는 차상신호장치의 기능 및 최고속도시험의 필요성을 분석하고, 고속선 ATC구간에서 최고속도시험을 실시하기 위한 인프라의 변경사항 및 구체적인 시험방안을 연구한다.