• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.688-694
• /
• 2009

A spray-type cleaning agent in utilizing dust-remover on PCB was chosen to study the cleanliness test and efficiency. In order to choose alternative environmental-friendly cleaning agents, it is important that the systematic selection procedures should be introduced and applied through the evaluation of their cleaning ability, environmental characteristics, and economical factors, and that the objective and effective evaluation methods of cleanliness should be established for the industry. A novel cleaning evaluation method with scanning electron microscopy/energy-dispersive X-ray analysis of surface observation evaluation method and an infra-red thermography camera(THERMOVISION A20 model) was studied in this work. The sound card(CT-2770 model) cut by $2{\times}2cm$ size was used as a part, and before and after the spray cleaning, the cleanliness was observed by the image analyzer of SEM and further the removal efficiency of dust was quantitatively evaluated by the component analysis of EDX. For the parts of P4TE model motherboard and IPC-A-36 PCB plate, before and after the spray cleaning, temperature differences were measured and compared at room temperature and 50 oven temperature by an infra-red thermography camera in the contaminants of dust and iron powder.

• Journal of Microbiology and Biotechnology
• /
• v.16 no.11
• /
• pp.1773-1777
• /
• 2006

We evaluated the usefulness of DNA microarray as a comparative genomics tool, and tested the validity of the cutoff values for defining absent genes in test genomes. Three genome-sequenced E. coli strains (K-12, EDL933, and CFT073) were subjected to comparative genomic hybridization with DNA microarrays covering almost all ORFs of the reference strain K-12, and the microarray results were compared with the results obtained from in silico analyses of genome sequences. For defining the K-12 ORFs absent in test genomes (reference strain-specific ORFs), we applied and evaluated the cutoff level of -1. The average sequence similarity between ORFs, to which corresponding spots showed a log-ratio of>-1, was $96.9{\pm}4.8$. The numbers of spots showing a log-ratio of <-1 (P<0.05, t-test) were 90 (2.5%) and 417 (10.6%) for the EDL933 genome and the CFT073 genome, respectively. Frequency of false negatives (FN) was ca. 0.2, and the cutoff level of -1.3 was required to achieve the FN of 0.1. The average sequence similarity of the false negative ORFs was $77.8{\pm}14.8$, indicating that the majority of the false negatives were caused by highly divergent genes. We concluded that the microarray is useful for identifying missing or divergent ORFs in closely related prokaryotic genomes.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.163-170
• /
• 1999

Although the bulge forming technique is currently employed in commercial superplastic forming processes, the uniaxial tensile test is still the most commonly used method for the evaluation of the superplasticity of materials due to its simplicity in testing. However, the results obtained from the uniaxial tensile test can not be applied in analyzing the characteristics of the real parts formed in multi-axial stress state. In this paper, using the tensile test specimen obtained from the square cup manufactured by superplastic forming, tensile strength and elongation have been investigated according to the strain and cavity volume fraction. From the result of experiment, tensile strength and elongation are decreased according to the strain and cavity in Al-6%Cu-0.4%Zr alloy. On condition of uniaxial stress, cavity volume fraction is increased on linear according to the increasement of thickness strain. However, on condition of biaxial stress there are critical point( E t=1.5-1.6) that the slope, the ratio of cavity volume fraction and strain, have been changed. Therefore, cavity volume fraction is different with respect to stress condition, although the same strain.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.187-194
• /
• 2020

The T&E (Test and Evaluation) results were applied for a judgment basis to decide the developmental process of system engineering for efficient weapon system R&D (Research and Development). During the OT&E (Operational Test and Evaluation) and DT&E (Development Test and Evaluation), an environmental test is essential for weapon system development owing to their highly exposed operational conditions. Based on the MIL-STD-810, MIL-HDBK-310, and AECTP 200, the ROK armed forces recommended operating temperatures for the ROK weapon system and applied this to the DT&E and OT&E. This study examined the compatibility of Korean temperature guidelines for stockpile material considering recent climate change. Moreover, this study analyzed the data from hourly measured temperatures on 101 observatories during 60 years, from 1960 to 2020, and percentage (0.5%, 1%, 5%, and 10%) and the 𝜎 (3𝜎, 2𝜎, and 1𝜎) frequency of occurrence on rigorous hot (August) and cold (January) periods, respectively. The results indicate that the highest temperature was 41℃, and the 0.5% frequency of occurrence was 37.0℃. In the case of the cold period, the lowest temperature was -32.6℃ and the 0.5% frequency of occurrence was -21.1℃. By considering the previously recommended operating temperature range for a general ground system, -30 ~ 40℃, regional operation probability is recognized 99.999%. Despite the recent abnormal climate change from global warming, the Korean temperature guidelines are compatible with the stockpile material environmental test.

• Journal of the Korean School Mathematics Society
• /
• v.10 no.3
• /
• pp.369-384
• /
• 2007

This study examined and compared the level of mathematical anxiety according to the types of students' characteristics based on the former research study showing that there exists a close relationship between characteristics and mathematical anxiety. The subjects of this study are 159 students enrolled in Chungnam Gongju and Kyunggi-do Ahnyang. They were categorized into groups following various standards such as preference index(E-1, S-N, T-F, J-P), ability & disposition, 16 types of characteristics. Then these were tested for types and the level of mathematical anxiety by the factors of mathematical anxiety. The results show that Type E students show the greatest anxiety in learning motivation, and Type N students in the pedagogy of teaching and loaming for the subfactor of mathematical anxiety. Further, Type NT students respond strongly to the pedagogy of teaching and loaming in psychological ability and disposition, which shows that mathematical anxiety and sub-factors of mathematical anxiety are closely somehow related.

• Land and Housing Review
• /
• v.11 no.4
• /
• pp.93-98
• /
• 2020

This study examined the particulate removal performance of three different types of air filters inside a heat exchanger. Of interest was the ability of each filter type in reducing the transmission of outdoor particulate matter of PM10 from entering an apartment while the heat exchanger was in operation. The study tested one commonly used medium filter (E11 grade) and two HEPA filters (H13 grade) of different thicknesses. Two different concentrations of particulate matter were used in the experiment to address different ambient air quality conditions in Korea, 32.75 ㎍/㎥ and 67.26 ㎍/㎥. Study results indicated that under the particulate matter concentration of 32.75 ㎍/㎥, all three filters were capable of removing more than 95% of the fine dust. However at a particulate matter concentration of 67.26 ㎍/㎥, the medium E11 grade filter was only able to remove about 90% of the particulates whereas the HEPA H13 grade filters were able to remove 95% or more of the particulates. The thicker HEPA filter (40T) was also more effective in removing particulates than the thinner HEPA filter (20T) by about 1.6 to 3 percentage points. Based on the findings of this study, it is recommended that HEPA filters of 20T thickness or greater be used during the high air pollution seasons of winter and spring in Korea while medium filters can be used during the other seasons to reduce outdoor air pollution transmission indoors.

• Korean Journal of Food Science and Technology
• /
• v.40 no.1
• /
• pp.101-105
• /
• 2008

Enterobacter sakazakii is implicated in severe forms of neonatal infections such as meningitis and sepsis. This organism has been isolated from a wide range of foods, including cheese, vegetables, grains, herbs, and spices, but its primary environment is still unknown. Generally, dried infant milk formula has been epidemiologically identified as the source of E. sakazakii. Sunsik (a powdered mixture of roasted grains and other foodstuffs) is widely consumed in Korea as a side dish or energy supplement. Sunsik is consumed without heat treatment; thus, lacking an additional opportunity to inactivate foodborne pathogens. Therefore, its microbiological safety should be guaranteed. In this study, the prevalence of E. sakazakii was monitored in 23 different sunsik component flours, using FDA recommended methods; but E. sakazakii medium (Neogen) and Chromogenic E. sakazakii medium (Oxoid) were used as the selective media. In total, presumptive E. sakazakii strains were isolated from 8 different sunsik powders. Subsequently, an API 20E test was conducted, and 15 strains from 5 different sunsik flours (sea tangle, brown rice, non-glutinous rice, cheonggukjang, dried anchovy) were confirmed as E. sakazakii. Fifteen strains were again confirmed by PCR amplification, using three different primer sets (tDNA sequence, ITS sequence, 16S rRNA sequence), and compared to ATCC strains (12868, 29004, 29544, 51329). They were once again confirmed by their enzyme production profiles using an API ZYM kit. Finally, RAPD (random amplified polymorphic DNA)-genotyping was carried out as a monitoring tool to determine the contamination route of E. sakazakii during processing.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.43-48
• /
• 2000

In this study, a small punch creep(SP-Creep) test using miniaturized specimen$(10{\times}10{\times}0.5mm)$ has been described for the development of the newly semi-destructive creep test method for high temperature structural components such as headers and tubes of boiler turbine casino and rotor and reactor vessel. The SP-Creep testing technique has been applied to 2.25Cr-1Mo(STBA24) steel used widely as boiler tube material and the creep test temperature are varied at $550^{\circ}C{\sim}600^{\circ}C$. The overall deformations of SP-Creep curves are definitely depended with applied load and creep test temperature and show the creep behaviors of three steps like conventional uniaxial creep curves. The steady state creep rate${\delta}_{ss}$ of SP-Creep curve for miniaturized specimen increases with increasing creep temperature, but the exponential value with creep loading is decreased. The activation energy$(Q_{spc})$ during SP-Creep deformation with various test temperatures shows 605.7kJ/mol that is g.eater than 467.4kJ/mol reported in uniaxial creep test. This may be caused by the difference of stress states during creep deformation In two creep test. But from the experimental results, e.g. SP-Creep curve behaviors, the steady state creep rate${\delta}_{ss}$ with creep temperature, and the exponential value(n) with creep loading, it can be summarized that the SP-Creep test may be a useful test method to evaluate the creep properties of the heat resisting material.

• International Journal of Oral Biology
• /
• v.41 no.4
• /
• pp.243-251
• /
• 2016

This study was undertaken to achieve a high bleaching efficacy with plasma, through longer application and reparative bleaching processes, by different shade evaluation methods. Extracted human teeth were divided into 6 groups (n=10). All teeth were treated in pairs. Low concentration of 15% carbamide peroxide (CP) was applied, with and without plasma, for 10, 20, and 30-min tooth bleaching, respectively. The bleaching procedure was repeated once daily for four days. The teeth were maintained in a moist environment provided by artificial saliva. The Vitapan Classical shade guide and Commission Internationale de L'Eclairage (CIELAB) color system were collectively used to measure the bleaching efficacy. Color evaluation was statistically analyzed using Student t-test and one-way analysis of variance (ANOVA) complemented by Tukey's test. Combining the plasma with 15% CP showed significantly greater color changes compared to bleaching without plasma (p<0.05). A high bleaching efficacy with plasma is proportional to the repetitive application and the treatment time. A 30-min application with plasma provided the best bleaching. Repetitive bleaching showed lower probability of color relapse of the bleached tooth. The color change by shade guide correlated with the changes in CIELAB color system. A value of 1 color change units (CCU) conversion factor for overall color change (${\Delta}E$) values comparisons was 3.724 values. The two measuring methods provide a more accurate correspondence of color change. The repetitive and longer application for tooth bleaching, combined with plasma, has a strong bleaching effect and produces whiter teeth.

• International Journal of Concrete Structures and Materials
• /
• v.2 no.2
• /
• pp.115-122
• /
• 2008

Ductility is important in the design of reinforced concrete structures. In seismic design of reinforced concrete members, it is necessary to allow for relatively large ductility so that the seismic energy is absorbed to avoid shear failure or significant degradation of strength even after yielding of reinforcing steels in the concrete member occurs. Therefore, prediction of the ductility should be as accurate as possible. The principal aim of this paper is to present the basic data for the ductility evaluation of reinforced high-strength concrete beams. Accordingly, 23 flexural tests were conducted on full-scale structural concrete beam specimens having concrete compressive strength of 40, 60, and 70MPa. The test results were then reviewed in terms of flexural capacity and ductility. The effect of concrete compressive strength, web reinforcement ratio, tension steel ratio, and shear span to beam depth ratio on ductility were investigated experimentally.