• Economic and Environmental Geology
• /
• v.28 no.1
• /
• pp.69-77
• /
• 1995

Tertiary Pohang basin distributed in south western part of the Korean peninsula, is composed of Chunbuk formation as the basal conglomerate, Hakjon formation, Duho formation and intrusive basalt having 15 Ma by absolute age data. The basement of the basin is represented to Cretaceous sedimentary rocks, Hakjon welded tuff and Chilpo welded tuff and rhyolite. The fault systems in the basement of Tertiary Pohang basin are consist of $N20^{\circ}E$ fault, $N60^{\circ}W$ and E-W trend. NNE fault is not only strike-slip but also normal dip-slip. WNW fault has sinistral strike-slip sense and the geometry of E-W fault is strike-slip and normal faults. In the basin, the fault system is represented to $N20^{\circ}E$ strike-slip, E-W normal and NNE thrust faults. By these fault relationship and geometry, it is interpreted that NNE sinistral strike-slip fault and N-S normal faults have acted at the Cretaceous basement. After Miocene NNE dextral strike-slip fault has acted and created E-W normal fault. Progressively Tertiary basin was influenced by the transpression to make thrust and fold, namely inversion tectonics.

• Journal of The Geomorphological Association of Korea
• /
• v.28 no.3
• /
• pp.63-83
• /
• 2021

In the southeastern part of the Korean Peninsula, the Yangsan Fault, an active fault zone, has developed. Many earthquakes occur around these faults, and the possibility of earthquakes occurring along the branch faults is being discussed. On the other hand, the Yeongdeok Fault is reported in Yeongdeok-gun, which is the northern part of the Yangsan fault. In this study, goemorphic characteristics of a set faults found on the outcrop of the gentle slope of the coast of Byeonggok-myeon were analyzed and granulometric and geochemical characteristics of sediments and other materials, including fault gouges were analyzed. The outcrop of Byeonggok-myeon is the part of the fault core and can be divided into two parts. Theses fault are formed on the upper part of the Mesozoic bedrock and the tertiary sedimentary layer of red sand-supported clasts are covered in several sedimentary units. The faults were normal fault sets, and a number of vertical cracks were developed, and glossy surfaces were observed in the fault area. It appears that these faults have occurred after alluvial deposition had been formed. In the case of samples from fault gouges, there were differences in particle size and geochemical characteristics from the surrounding area.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.107-112
• /
• 2005

Road is built continuously along with development of industry and cut slope is happened necessarily in road construction. Geoengineers are executing cut slope stability analysis considering various cut slope condition such as topography, geology, hydraulic condition and so on. The Tertiary Jungja Basin is located in the southeastern coastal area of the Korea Peninsula. Jungja Basin area is created by geotectonic movement of the plate after Early Miocene epoch. The northwestern and southwestern boundary of the basin is fault zone. The Basement rock is hornfels (Ulsan Formation). Basin-fills consist of extrusive volcanic rock(Tangsa Andesites), unconsolidated fluviatile conglomerate(Kangdong Formation) and shallow brackish-water sandstone(Sinhyun Formation). The characteristics of cut slopes in this area is different with cut slopes in the other site. Soil layers in this area is unconsolidated sediments and is not formed the weathering and erosion of the rock. So, the depth of soil layer is very thick. Faults of this area are northwest-southeast and northeast-southwest direction. Expandible clay mineral as smectite, chlorite et al. detected from fault gouge using XRD. Therefore, Jungja Basin area must consider the characteristics of the faults and soil layers thickness necessarily cut slopes stability analysis.

• Economic and Environmental Geology
• /
• v.9 no.1
• /
• pp.1-11
• /
• 1976

It is believed that geological survey, drilling and geophysical survey which was carried out on Tertiary deposits in Pohang is a valuable but through the studying of many Tertiary sediments in Japan discovered many questions on analysis of final report prepared by National geological survey. The main reason is: 1. The seismic sound velocity which have regulated in the final report prepared by geological survey for Tertiary deposits in Pohang was 1,500-2,000m/sec in spite of oil bearing sediments of same age in Japan are 2,000-3,800m/sec. These may means the requirement of reconsideration of seismic velocity for Tertiary deposits in Pohang and required to have a dipper drilling. 2. Stratigraphically, geophysically, and paleontologically, the Tertiary deposits in Pahang land area is similar with that of Nishiyama-Hunakawa formations of Akita oil field in Japan. Nishiyama-Hunakawa formation is the main oil bearing formation in Japan. 3. Those valcanic rock including andestitic rock and liparitic rock which have extensively distributed over either at land area or at sea bottom, assumed by geological survey as the base of Tertiary sediments. But in case of Japan many oil bearing deposits are in over laid by these kind of volcanic rock. Therefore a possible of same condition with Japan is presumable on Tertiary sediments in Pohang. 4. It is believed that the Tertiary sediments of land area in Pohang is the extension of offshore basin but is wandering that the final report submitted by geologic survey have not remain any word on report of ECAFE discribed so much problematics as followed: A. Although it was assumed that no great thickness exceeding 1,000 meters, or major structures would be encountered in the Tertiary offshore sequence, it was hoped that shallow hydrocarbon deposits might be found, because these sediment are lithologically similar to those of the same age in the producing area of the northwest Honshu region of Japan where hydrocarbon are extracted from depths of only 500 to 600 meters. B. Four possible hydrocarbon trap conditions are represented in the survey area: anticlinal folds, faults, pinch outs, along the igneous basement and lateral facies changes. C. Most of the prime possible reservoir area are beyond the 50 meter water depth mark, except for the structures in Yonil Bay. D. Despite the shallowness of the offshore basin, sufficient trap condition exist in the area to warrant further exploration for hydrocarbon. 5. All of the problems mentioned above have gave us a strong reasons to have us hesitating to make a final conclusion on Tertiary problems in Pohang, before to have a drill to a depth to 3,000 meters or more whatever it is the Tertiary or a Mesozoics below 1,000 meters.

• Economic and Environmental Geology
• /
• v.33 no.3
• /
• pp.217-228
• /
• 2000

We use spectral correlation method to analyze gravity and magnetic anomalies of Euiseong Sub-basin for distribution of rock facies and gelogic structures. The analysis reveals distinct polarity between gravity and magnetic anomaly correlation ; intermediate to mafic intrusives, extrusives, and the Tertiary basin shows positive gravity (+G) and positive magnetic (+M) correlation. Granitic gneiss and felsic volcanics negative gravity 9-G) and negative magnetic (-M) correlation. The Palgongsan granite, felsic to mafic extrusives and Mesozoic granites are characterized by -G and + M correlation. +G and -M correlations in the sedimentary formations are interpreted by uplift of pre-Cretaceous basement rocks . The + G and + M correlation characteristics in northeastern part of Euiseong Sub-basin including the Tertiary sedimentary basin result from the uplift of crustal materials. Major axes of spectrally correlated amomalies have mostly NW-SE or NE-SW directions. The former is due to the intrusives along strike-slip faults, and the latter which is observed in sedimentary formations is related to geological structures of basement associated new insight into the boundary between Euiseong and Milyang Sub-basin.

• The Journal of Engineering Geology
• /
• v.34 no.3
• /
• pp.447-457
• /
• 2024

This study investigated a cut-slope surface containing Tertiary faults, representing a conical-shaped slope with strike varying from N44°E to NS, N50°W, and finally N70°E. The slope consists mainly of basalt, with discontinuities in the slope including faults, fault zones, fracture zones, shear joints, and extension joints. The type and scale of failure vary with the strike of the slope and the strikes of discontinuities, with plane and wedge failure predominating. Based on face-mapping data, SMR (slope mass rating), rock physical and mechanical properties, analysis of stereonet projections and geological cross-sections, and critical equilibrium analysis, optimal slope stability determination was found to involve the countermeasure method, the slope gradient relief method, the green soil surface treatment method, and a fall prevention measure. After application of the countermeasure method, both dry and wet slope conditions exceeded allowable safety factors. It is expected that the preparation of geological cross-sections of various representative sections perpendicular to the surface of the slope, and the application of corresponding countermeasure methods, will be reasonable tools for three-dimensional analysis of slope stability. If the strike of the slope varies widely, it is necessary to prepare geological cross-sections, and the section used for critical equilibrium analysis must be established as the basic section.

• Economic and Environmental Geology
• /
• v.27 no.1
• /
• pp.65-80
• /
• 1994

The Tertiary $Ch{\check{o}}ngja$ basin is located in the southeastern coastal area of the Korean Peninsula. It is a lozenge shaped fault-bounded basin with circa $5{\times}5km$ areal extent, isolated from other Tertiary basins by the Cretaceous Ulsan Formation in-between. The northwestern boundary of the basin is a domino/listric type normal fault trending $N30^{\circ}E$, whereas its southwestern boundary is a dextral strike-slip fault (trending $N20^{\circ}W$) with a lateral offset of more than 1 km. The basin is bounded by the East Sea on the eastern margin. Basin-fills consist of extrusive volcanic rock (Tangsa Andesites) of Early Miocene (16~22 Ma in radiometric age), unconsolidated fluviatile conglomerate (Kangdong Formation) and shallow brackish-water sandstone ($Sinhy{\check{o}}n$ Formation). The latter yields abundant Vicarya-Anadara molluscan fossils of early Middle Miocene age. The Tertiary strata become younger toward the northwestern boundary-fault of the basin, showing a zonal distribution pattern parallel to the fault: the younger sedimentary formations occupy a narrow zone of 2 km width along the northwestern boundary-fault, whereas the older Tangsa Andesites underlie them unconformably in the eastern and southeastern portions of the basin. The strata in the basin, including the Tangsa Andesites, are tilted (about $20^{\circ}$) toward the northwestern boundary-fault Sedimentary strata thicken toward the boundary-fault, forming a wedge shaped half-graben structure. A number of small-scale syndepositional normal growth faults and graben structures are observed in the sedimentary strata. These extensional structures have the same trend as the normal northwestern boundary-fault which we interpret as a pull-apart detachment fault. These characteristics imply persistent extension during the basin evolution, caused by a NW-SE directed tensional force. The $Ch{\check{o}}ngja$ basin is, thus, a kind of syndepositional tectonic basin evolved in a strike-slip (pull-apart) regime. The latter was caused by a dextral simple shear associated with the NNW-SSE opening of the East Sea. In view of the fact that the normal growth faults do not cut through the uppermost portion of the youngest $Sinhy{\check{o}}n$ Formation, it is inferred that the tensional force came to be inactive in the early Middle Miocene. This is coincident in timing with the termination of the East Sea opening (15 Ma).

• The Journal of Engineering Geology
• /
• v.17 no.1 s.50
• /
• pp.27-40
• /
• 2007

Stratigraphy has been renewedly set up and the evolution of tectonic events related to basin formation has been exam-ined on the basis of fault-slip data analysis in the Tertiary Eoil and Waeup basins of the southeastern part of Korea. First of all, field mapping was carried out in detail for Tertiary formations and then paleostress analysis were peformed with more than 400 fault slip data collected from 11 sites in the Tertiary formations and the Yucheon Group. It is judged that both the Eoil and Waeup basins filled up with Tertiary deposits might be simultaneously formed in separate locations. The Janggi Group in the Eoil basin is divided into following stratigraphic units in ascending order: Gampo Conglomerte, Hongdeok Basalt, Nodongri Conglomerate and Yeondang Basalt, and the Bomkori Group in the Waeup basin: Waeupri Tuff; Andongri Conglomerate, Yongdongri Tuff and Hoamri Volcanic Breccia. Paleostress analysis by using striated faults reveals five sequential tectonic events: (1) NW-SE transtension (event I), (2) NW-SE transpression (event IIl), (3) NE-SW pure extension (event III), (4) N-S transpression (event IV) and (5) E-W pure compression (event V). Therefore, five sequential tectonic movements are closely associated with the formation and evolution of the Tertiary basins in the study area: tectonic event I of NW-SE extension is related to formation of the Tertiary basins during the late Oligocene to the Early Miocene, tectonic events II, III and IV caused the termination of the Tertiary basin opening and the crustal uplift in the study area, and tectonic event V upheaved the east coast or Korean Peninsula with compressive stress due to intense subduction of the Pacific plate into Asian continent since the Early Pliocene.

• 한국석유지질학회:학술대회논문집
• /
• autumn
• /
• pp.57-72
• /
• 2000

The Murzuk Basin covers an area in excess of $350,000{\cal}km^2$, and is one of several intra-cratonic sag basins located on the Saharan Platform of North Africa. Compared with some of these basins, the Murzuk Basin has a relatively simple structure and stratigraphy, probably as a result of it's location on a the East Saharan Craton. The basin contains a sedimentary fill which reaches a thickness of about $4,000{\cal}m$ in the basin centre. This fill can be divided into a predominantly marine Paleozoic section, and a continental Mesozoic section. The principal hydrocarbon play consists of a glacial-marine sandstone reservoir of Cambro-Ordovician age, sourced and sealed by overlying Silurian shales. The present day borders of the basin are defined by tectonic uplifts, each of multi-phase generation, and the present day basin geometry bears little relation to the more extensive Early Palaeozoic sedimentary basin within which the reservoir and source rocks were deposited. The key to the understanding of the Cambro-Ordovician play is the relative timing of oil generation compared to the Cretaceous and Tertiary inversion tectonics which influenced source burial depth, reactivated faults and reorganised migration pathways. At the present day only a limited area of the basin centre remains within the oil generating window. Modelling of the timing and distribution of source rock maturity uses input data from AFTA and fluid inclusion studies to define palaeo temperatures, shale velocity work to estimate maximum burial depth and source rock geochemistry to define kinetics and pseudo-Ro. Migration pathways are investigated through structural analysis. The majority of the discovered fields and identified exploration prospects in the Murzuk Basin involve traps associated with high angle reverse faults. Extensional faulting occurred in the Cambro-Ordovician and this was followed by repeated compressional movements during Late Silurian, Late Carboniferous, Mid Cretaceous and Tertiary, each associated with regional uplift and erosion.

• Economic and Environmental Geology
• /
• v.25 no.2
• /
• pp.167-177
• /
• 1992

The gravity measurement has been conducted at 53 and 34 stations with an interval of 1~1.5 km along the national roads of about 47 km and 34 km running from Duksungri to Yangpori and from Angangri to Byungpori, Kyungsangbookdo, respectively. The subsurface geology and geologic structure of Tertiary Pohang and Janggi basins along two survey lines are interpreted quantitatively by applying Fourier series and Talwani methods for Bouguer gravity anomaly. The depths of Conrad discontinuity vary from 11.8 to 12.5 km and 11.5 to 13.2 km along the survey lines between Duksungri and Yangpori, and Angangri and Byungpori, respectively. The depths of pre-Cambrian Gneiss complex underneath Kyungsang Supergroup vary from 3.8 to 4.2 km and 3.8 to 4.6 km along the survey lines between Duksungri and Yangpori, and Angangri and Byungpori, respectively. Massive granite bodies which are not exposed along the survey line between Duksungri and Yangpori are distributed on a large scale at the subsurface between Duksungri and Ochun, and Daegokri and Yangpori. Along the survey line between Angangri and Byungpori, it is exposed at Angangri, and extends underneath Chungrimdong, Pohang city. Andesite is distributed on a small scale underneath Pohang city and Ochun. The thicknesses of Tertiary Yonil and Janggi Groups are 0.2~0.9 km and 0.1~0.5 km, respectively. The Tuffaceous rocks which are the lowest formation of Tertiary sedimentary rocks are distributed with the thickness of 0.2 km at the surface and between Kyungsang Supergroup and Yonil or Janggi Groups. The Yonil and Janggi Groups are in fault contact by a fault running through Ochun and Chungrimdong, Pohang city. Two other faults are newly found near Heunghae-eup and Hyungsan river.