• Journal of Satellite, Information and Communications
• /
• v.2 no.1
• /
• pp.7-13
• /
• 2007

A new and effective Doppler effects compensation method based on constellation estimation as well as an average power saving strategy by modified modulation scheme utilizing zero point constellation are presented with theoretical analysis and relevant simulations. The suggested schemes are proved to be very effective for satellite OFDM signals relayed by power limiting transponder for the mobile terminal on high speed vehicles.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.4
• /
• pp.36-41
• /
• 2014

Most faults that occur on transmission lines are caused by extreme weather with lightning storms in the distance. These are not only prolongs the time of removing and recovering, but also increases economical damages. If faults can be precisely located, maintenance crews can reach them quickly, and remove the faults in time. So, the precise locating of the faulted point on a transmission line is very important to improve the system reliability, and decreases economic damages as an inherent consequence of long term outages. Also, fault location methods are becoming of much importance for utilities and research. In this paper, two single-terminal impedance-based fault location techniques will be investigated to show the reliability and evaluated the performance of reactance and Takagi method by using MATHCAD program simulations.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.9
• /
• pp.8-15
• /
• 2010

This paper analyzes the steady-state output characteristics of variable-speed wind turbine systems using doubly-fed induction generators(DFIG) compared with fixed-speed induction generator(FSIG) wind turbine systems. It also presents simulations of a grid-connected wind turbine generation system for dynamics analysis on MATLAB/Simulink and compares the responses between DFIG and FSIG wind turbine systems with respect to wind speed variation, impedance changes and X/R ratio changes of interconnecting circuits. Simulation results show the variation of generator's active output, terminal voltage and fault currents at the interconnecting point. Case studies demonstrate that DFIG wind turbine systems illustrate better performance to 3-phase fault than FSIG's.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.59 no.3
• /
• pp.325-329
• /
• 2010

Capacitor has been used principally for the power factor compensation long ago. However now it does as passive filter to reduce harmonics of nonlinear load with reactor. Most of the customer's low-voltage feeder has been designed with approximately balanced and connected at the 3 phase four wire system. But voltage and current unbalance is appeared by the mixing operation of single or three phase load etc. The addition of reactor at the condenser may rise its terminal voltage. Voltage and current values above rating can act on electrical stress on the condenser. In this paper, we calculated and measured that voltage, current and capacity of condenser are changed under the voltage balance. We conclude that magnitude and deviation of phase voltage act on major point of electrical stress.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.2
• /
• pp.167-174
• /
• 1996

In this paper, a fault location algorithm is presented, which uses novel signal processing techniques and takes a new paradigm to overcome some drawbacks of the conventional methods. This new method for fault location on electric power transmission lines uses only one-terminal fault signals. The main feature of the method is hat it uses the high frequency components in fault signal and considers the influence of the source network by using a traveling wave propagation characteristics. As a result, we can develop a high speed, good accuracy fault locator.

• Journal of Information Processing Systems
• /
• v.11 no.4
• /
• pp.616-629
• /
• 2015

A mobile terminal will expect a number of handoffs within its call duration. In the event of a mobile call, when a mobile node moves from one cell to another, it should connect to another access point within its range. In case there is a lack of support of its own network, it must changeover to another base station. In the event of moving on to another network, quality of service parameters need to be considered. In our study we have used the Markov decision process approach for a seamless handoff as it gives the optimum results for selecting a network when compared to other multiple attribute decision making processes. We have used the network cost function for selecting the network for handoff and the connection reward function, which is based on the values of the quality of service parameters. We have also examined the constant bit rate and transmission control protocol packet delivery ratio. We used the policy iteration algorithm for determining the optimal policy. Our enhanced handoff algorithm outperforms other previous multiple attribute decision making methods.

• IE interfaces
• /
• v.7 no.3
• /
• pp.69-76
• /
• 1994

In this paper, we develop a real-time manufacturing control and information management(POP) system that can support realization of CIM and information network of manufacturing system. The POP system systematically collect informal data that is originated from working area and make an offer collected information to planning side. Especially, this study designs a modular POP terminal that directly extract and process momentary information from field source and provide it to control system on real-time. In addition, we apply developed POP system with open architecture to flexibly and optimally operate the manufacturing system based on CIM.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.1
• /
• pp.80-84
• /
• 2012

Recently, the small scale photovoltaic (PV) electronic devices are drawing attention as the upcoming PV generation system. The PV system is commonly used in small scale PV applications such as LED lighting and cell phone. This paper proposes photovoltaic output sensorless (POS) maximum power point tracking (MPPT) control for a small scale charging system of PV-nickel metal hydride battery using field-programmable gate array (FPGA) controller. A converter is connected to a small scale PV cell and battery, and performs the POS MPPT at the battery terminal current instead of being at the PV cell output voltage and current. The FPGA controller and converter operate based on POS MPPT method. The experimental results show that the nickel metal hydride battery is charged by the maximum PV output power.

• Journal of Chest Surgery
• /
• v.3 no.2
• /
• pp.139-142
• /
• 1970

A Case of thoraco-abdominal aortic aneurysm involving from the lower descending- thoracic aorta to bifurcation of abdominal aorta into both common iliac artery is presented in special view-point of its surgical technic and postoperative complication. Operative technic is the most popular method of Dr. De Bakey's shunt of Dacron which is bridging thoracic aorta to terminal abdominal aorta primarily as temporary shunt but after anastomosing the individual hranch of left Renal, Celiac, Sup. meseateric and right Renal artery to corresponding part of the Dacron tube, the Dacroa graft is fixed as permanent graft in stead of excised thoraco-abdominal aorta. The patient died of acute renal failure and increasing evidence of CNS damage due to respiratory acidosis on 6th postoperative day hut this report will he a good experience in respect of further progress of aortic surgery in Korea.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.41.3-41
• /
• 2001

In this paper, we present a decentralized adaptive neural net(NN) controller for the transient stability and voltage regulation of a multimachine power system. First, an adaptively input-output linearizing controller using NN is designed to eliminate the nonlinearities and interactions between generators. Then, a robust control term which bounds terminal voltage to a neighborhood of the operating point within the desired value is introduced using only local information. In addition, we consider input saturation which exists in the SCR amplifier and prove that the stability of the overall closed-loop system is maintained regardless of the input saturation. The design procedure is tested on a two machine infinite bus power system.