• Journal of Welding and Joining
• /
• 제16권5호
• /
• pp.86-92
• /
• 1998

High speed wire seam weldability of tin coated thin gage sheet steels was investigated. Thickness and coating weight ranges of the test materials were 0.21~0.35mm and 1.1/1.1~2.8/11.2g/$m^2$, respectively. Test results indicated that the surface roughness value, Rz decreased as increasing the coating weight. The Rz was thought to be one of the important factors to influence the optimum welding condition range, $\triangle$Q. The $\triangle$Q showed close relationship with welding conditions such as welding pressure and travel speed. Higher welding pressure widened the $\triangle$Q while higher travel speed reduced the $\triangle$Q value. Results also demonstrated that tin coating weight should be optimized based on the weldability or the serviceability after welding. At th HAZ of sheet materials with thinner coating layer, tin depleted zone was produced since molten film of the coating material on the base metal agglomerated by the surface tension, which could result in reducing the corrosion resistance of the HAZ in the service environment.

• Journal of Welding and Joining
• /
• 제14권2호
• /
• pp.71-78
• /
• 1996

In order to rpovide proper SMT design criteria in a systematic way, a mathematical formulation has been developed to predict the configuration of the solder fillet formed between the gullwing type lead and rectangular pad. Effects of SMT design parameters such as the solder volume and pad dimension on the solder profile are investigated using the FEM that calculates the 3D configuration by minimizing the energy due to surface tension and gravity in the equilibrium state. Design criteria of QFP and SOP are illustrated by plotting the acceptable range of the solder volume with respect to the length and width ratios of the pad and lead. The results show that the acceptable design range increases with increase in the pad length and width. The pad length has more significant effects on design criteria compared with the pad width, and Bond number can be utilized to predict the joint quality.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1869-1874
• /
• 2003

Polymeric fibers with nanometer-scale diameters are produced by electrospinning. When the electrical forces at the surface of a polymer solution or melt overcome the surface tension then electrospinning occurs. Polyethylene oxide (PEO), Polycarbonate have been electrospun in our laboratory. Electrospun fibers are observed by optical microscopy or scanning electron microscopy. The average diameters of the electrospun fibers range from 300 nm to 30 nm when the electric field strength increasing from 1 kV/cm to 3 kV/cm. The average diameters of the electrospun fibers range from 200 nm to 30 nm when the concentration decreasing from 10 wt% to 4 wt%.

• Clinical and Experimental Pediatrics
• /
• 제54권9호
• /
• pp.359-362
• /
• 2011

There is a delicate balance between too little and too much supplemental oxygen exposure in premature infants. Since underuse and overuse of supplemental oxygen can harm premature infants, oxygen saturation levels must be monitored and kept at less than 95% to prevent reactive oxygen species-related diseases, such as retinopathy of prematurity and bronchopulmonary dysplasia. At the same time, desaturation below 80 to 85% must be avoided to prevent adverse consequences, such as cerebral palsy. It is still unclear what range of oxygen saturation is appropriate for premature infants; however, until the results of further studies are available, a reasonable target for pulse oxygen saturation ($SpO_2$) is 90 to 93% with an intermittent review of the correlation between $SpO_2$ and the partial pressure of arterial oxygen tension ($PaO_2$). Because optimal oxygenation depends on individuals at the bedside making ongoing adjustments, each unit must define an optimal target range and set alarm limits according to their own equipment or conditions. All staff must be aware of these values and adjust the concentration of supplemental oxygen frequently.

• 대한후두음성언어의학회지
• /
• 제14권1호
• /
• pp.47-50
• /
• 2003

The transgender is who has persistent discomfort with his of her sex or sense of inappropriateness in the gender role of that sex. Many transgenders have been undergone trans-sex operations after 1980's. But there were not so much experience of voice surgery for transgenders. Vocal pitch can be elevated by various surgical techniques. Type IV thryoplasty, which one of the cricothyroid approximation methods, increases tension to the vocal folds, thus increasing fundamental frequency and upper pitch range. We treated a transgender (MTF, Male to female) using this technique. Acoustic and aerodynamic measures were obtained both pre- and post-operatively. Clinically significant improvement was achieved in both study; increasing of vocal pitch, widening of pitch range, and improvement of vocal efficiency.

• 대한조선학회논문집
• /
• 제33권4호
• /
• pp.133-141
• /
• 1996

하중 전달형 필릿 용접 이음부에서 피로파괴는 용접투우부와 용접루트부로 부터 발생된 피로균열 발생 및 전파의 특성에 지배된다. 또한 그 피로균열의 특성은 필릿의 형상과 응력범위에 따라 큰 영향을 받는다. 본 연구의 목적은 하중 전달형 십자형 필릿 용접 이음부에서 피로하중 작용시 용접토우부에서 파괴하기 이한 용접부의 임계다리길이와 응력범위등을 검토하는 것이다.

• 대한화장품학회지
• /
• 제10권1호
• /
• pp.24-41
• /
• 1984

Tallow fatty acid consists of mixtures of fatty acids differing in chain length and saturation. In separation of tallow fatty acid, the effects of the type and concentration of detergents and electrolytes were studied. And the changes of acid composition of particular fractions were determined by gas-chromatography. Sodium lauryl sulfate (SLS), sodium lauryl ether sulfate (SLES) and sodium lauryl benzene sulfonate (SLBS) were used as detergents and NaCl, Na2SO4 and MgSO4 were used as electrolytes. At low concentration of detergent, the tallow fatty acid was not fully wetted, and at high concentration, the emulsion was so stable that the tallow fatty acid was not well separated. The addition of proper amount of electrolyte increased the separation efficiency by the decrease of interfacial tension and by the increase of the amount of adsorbed detergent on the surface of solid fatty acid crystals. The optimum range of detergent was 0.4-0.6% (wt.) in SLS, 0.2-0.4% in SLES and 2.0-) .0% in SLBS. And the optimum range of electrolyte was 2.0-2.5% in NaCl, 3.0-4.0% In Na2SO4 and 0.5-1.0% in MgSO4 respectively.

• 한국해양공학회지
• /
• 제14권2호
• /
• pp.99-105
• /
• 2000

This paper describes the effect of specimen size on fatigue crack growth rate for the offshore structural high-tensile-strength steel BS4360 and machine structural steel SM45C. The purpose of the present study is to investigate the effect of stress ratio aspect ratio specimen width and specimen thickness of the fatigue crack growth behavior. Compact tension specimens with a LT orientation for BS4360 and SM45C steels were used, All testing was done at constant stress intensity factor range controlled fatigue crack growth condition. The investigation demonstrates that the fatigue crack growth rate is increased with increasing stress ratio and specimen thickness and is decreased with increasing specimen width. The fatigue crack growth rate is unaffected by aspect ratio until a/W=0.50 but is increased by increasing spect ratio from a/W=0.55.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.155-160
• /
• 2002

Metal matrix composites had generated a lot of interest in recent times because of significant in specific properties. It was also highlighted as the materials of frontier industry because strength, heat-resistant, corrosion-resistant, wear-resistant were superiored. In this study the strength properties of $Al_{18}B_4O_{33}/AC4CH$ were represented mixing the binder of $Al_2O_3$ and $TiO_2$. It was also fabricated by squeeze casting. $Al_{18}B_4O_{33}/AC4CH$ was fabricated at the melt temperature of $760^{\circ}C$ the perform temperature of $700^{\circ}C$ and mold temperature of $200^{\circ}C$ under the pressure of 83.4MPa and observed SEM. Fatigue crack growth rate tests on compact tension specimen(half-size) of thickness 12.5mm were conducted by using sinusoidal waveform. Compact tension specimens(half-size) were used and fatigue crack growth rate da/dN and stress intensity factor range ${\Delta}K$ were analyzed concerning to the R value of 0.1 and 0.05. In order to find out the value of ${\Delta}K$, load amplitude constant method was applied by the standard fatigue testing method describes in ASTM E647-95a. As the results of this study, Fatigue crack growth rate increased with in creasing the load ratio, Consequently, At equivalent stress intensity factors, the fatigue crack growth rates in MMC were faster than those of AC4CH alloy. then the fatigue life and the fatigue crack growth rate was investigated using scanning election microscopy(SEM)

• Smart Structures and Systems
• /
• 제19권3호
• /
• pp.335-340
• /
• 2017

Fiber Bragg grating (FBG) sensors are applied to structural health monitoring (SHM) in many areas due to their unique advantages such as ease of multiplexing and capability of absolute measurement. However, they are exposed to cyclic thermal load, generally in the temperature range of $-20^{\circ}C$ to $60^{\circ}C$, in railways during a long-term SHM and the cyclic thermal load can affect the mechanical strength of FBGs. In this paper, the effects of both cyclic thermal load and the reflectivity of FBGs on the mechanical strength are investigated though tension tests of FBG specimens after they are aged in a thermal chamber with temperature changes in a range from $-20^{\circ}C$ to $60^{\circ}C$ for 300 cycles. Results from tension tests reveal that the mechanical strength of FBGs decreases about 8% as the thermal cycle increases to 100 cycles; the mechanical strength then remains steady until 300 cycles. Otherwise, the mechanical strength of FBGs with reflectivity of 6dB (70%) and 10dB (90%) exhibits degradation values of about 6% and 12%, respectively, compared to that with reflectivity of 3dB (50%) at 300 cycles. SEM photos of the Bragg grating parts also show defects that cause their strength degradation. Consequently, it should be considered that mechanical strength of FBGs can be degraded by both thermal cycles and the reflectivity if the FBGs are exposed to repetitive thermal load during a long-term SHM.