• 한국압력기기공학회 논문집
• /
• 제14권1호
• /
• pp.58-65
• /
• 2018

The purpose of this study is to develop a Half Nozzle Repair(HNR) process to prevent the leakage from welds on small bore piping in Reactor Coolant System. The Codes & Standards of tempered bead and design requirements of J-Groove welds are reviewed. Automatic machine GTAW welding and machining equipments are developed to perform HNR process. Single pass welding and overlay welding equipments are conducted in order to obtain the optimal temper bead welding process parameters with Alloy 52M filler wire. Coarse grain heat affected zone(CGHAZ) is formed by rapid cooling rate in heat affected zone after welding. Accordingly, a proper temper bead technique is required to reduce CGHAZ in 1-Layer of welds by 2- and 3-Layers. Mock-up tests show that the developed HNR process is possible to meet ASME Code & Standard requirements without any defect.

• 대한기계학회논문집
• /
• 제16권10호
• /
• pp.1861-1868
• /
• 1992

본 연구에서는 발전소의 터빈 블레이드는 물방울에 의해서 부식이 발생한다는 사실은 널리 알려져 있다. 부식을 방지하기위해서 보통 12%-Cr 강으로 만들며 표면 을 고주파 유도경화법에 의해서 표면을 경화시킨다. 고주파유도 경화법은 경화층 깊 이가 마모 특성을 가장 좋게 하는 깊이보다 훨씬 깊게 경화되며, 열응력이 과대하게 생기고, 처리시간이 많이 걸리며, 표면경화 처리후 기계가공이 필요하다. 12%-Cr 강 의 레이저 표면경화를 연속파 3kw CO$_{2}$ 레이저로 실험하여 금속조직과 경도분포에 대해서 연구하여 레이저 표면경화 가능성을 고찰하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.84-88
• /
• 1992

Laser beam hardenling of 12%-Cr steel has been evaluated by using a continuous wave 3 kW CO$\_$2/ laser with a hardening mirror set. Experiment was performed on the optimum hardening condition with a laser power of 2.85kW and travel speed of 10 and 5 m/min. Multi passes have been alsotried to find the hardening characteristics of partly overlapped zone. The black paint to use at high temperature was adopted to increases the absorptivity of laser beam energy with the wavelength of 10.6 .mu. m at the surface of bese metal. The microstructure of the hardened layers was observed by using a light microscopy. SEM and TEM. A fine lamellar martensite formed in the hardened zones exhibits very high Vickers microhardness of 600 Hv, whereas the tempered martesite distributes in the base metal with Vickers microhardness of 240 Hv. It has been found that laser hardening with multi pass showed no significant drop of the hardness between adjacent passes.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 춘계학술발표회논문집(2)
• /
• pp.17-22
• /
• 1997

ASME SA508 Class 3 원자로압력용기강을 대상으로, 용접열영향부(heat affected zone, HAZ)의 최고온도(peak temperature) 등온분포도(isothermal diagram)를 작성 및 해석하였고, 재현(simulated) 열영향부 시험편을 제작하여 미세조직검사 및 기계적특성 시험을 실시하였다. 그 결과, 최고온도 등온분포도를 이용하여, 미소열영향부(subzone of HAZ)의 미세조직(microstructure)에 미치는 예열(preheat)온도와 용접입열량(weld heat input)의 크기 효과를 예측할 수 있었다. 또한, 재현 HAZ 의 기계적특성 시험결과, 용접용융선(fusion line) + 1 mm 이내의 위치로 대표되는 열 cycle 조건에서는 모재보다 양호한 강도와 인성을 보였고, 용접용융선 + 2~3mm부근에서 가장 미세한 조직(fine tempered lower bainite)과 우수한 충격인성을 나타냈다. 한편, 용접용융선 + 약 5mm 위치에서의 열 cycle 을 재현한 시험편에서는 미세조직의 변화(spheroidization of carbides)와 함께 인성 및 기계적 특성이 저하하여 모재보다 낮은 값을 보이는 것을 발견할 수 있었다.

• Journal of Welding and Joining
• /
• 제35권3호
• /
• pp.68-74
• /
• 2017

Characteristics of dissimilar metal welds between alloy steel ASTM A387 Gr. 91 and carbon steel ASTM A516 Gr.70 made with Flux cored arc welding(FCAW) have been evaluated in terms of microstructure, mechanical strength, chemical analysis by EDS as well as corrosion test. Three heat inputs of 15.0, 22.5, 30.0kJ/cm were employed to make joints of dissimilar metals with E71T-1C wire. Post-weld heat treatment was carried out at $750^{\circ}C$ for 2.5 h. Based on microstructural examination, Intragranular polygonal ferrite and grainboundary ferrite were formed only in first layer of weld metal. Another layers consisted of acicular ferrite and $Widmannst{\ddot{a}}tten$ ferrite. The amount of acicular ferrite was increased with decreasing heat input and layer. Heat affected zone of alloy steel showed the highest hardness due to the formation of tempered martensite and lower bainite. Lower and upper bainite were formed in heat affected zone of carbon steel. Tensile strengths of dissimilar metal welds decreased with increasing heat inputs. Dissimilar metal welds showed a good hot cracking resistance due to the low HCS index below 4. The salt spray test of dissimilar metals welds showed that the weight loss rate by corrosion below 170 hours was decreased with increasing heat inputs due to the increase of the amount of acicular ferrite.

• Journal of Welding and Joining
• /
• 제17권3호
• /
• pp.55-65
• /
• 1999

Metallurgical factors influencing toughness of the Intercritically Reheated Coarse-Grained Heat Affected Zone (ICCG HAZ) of multiple welded SA508-cl.3 Reactor Pressure Vessel Steel were evaluated. The recrystallized austenite formed along the prior austenite grain boundaries and late interfaced on heating to the intercritical range was transformed to bainite and/or martensite during cooling. The newly formed martensite always included some retained austenite(M-A constituents). The characteristics(amount, hardness, density, and size) of M-A constituents were found to be strongly associated with both peak temperature and cooling time(△t8/5(2)) of last pass. Toughness in the ICCG HAZ was deteriorated with increasing amount of M-A constituents which was increased with increasing the last peak temperature within the intercritical temperature range. Meanwhile, for the same intercritical peak temperature, toughness was decreased with increasing cooling time. When cooling time was short, the dominant factor influencing toughness of the ICCG HAZ was amount of M-A constituents. However, when cooling time was lengthened, the hardness difference between M-A constituents and softened matrix(tempered martensite) was found to be the dominant factor.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.58-64
• /
• 2013

Several joining methods involving resistance welding, laser welding, ultrasonic welding and mechanical joining are currently applied in manufacturing lithium-ion batteries. Cu and Al alloys are used for tab and bus bar materials, and laser welding characteristics for these alloys were investigated with similar and dissimilar material combinations in this study. The base materials used were Al 1050 and oxygen-free Cu 1020P alloys, and a disk laser was used with a continuous wave mode. In bead-on-plate welding of both alloys, the joint strength was higher than the strength of O tempered base material. In overlap welding, the effect of welding parameters on the tensile shear strength and bead shape was evaluated. Tensile shear strength of overlap welded joint was affected by interfacial bead width and weld defect formation. The tensile-shear specimen was fractured at the heat affected zone by selecting proper laser welding parameters.

• 비파괴검사학회지
• /
• 제20권5호
• /
• pp.390-396
• /
• 2000

원자로 재료인 SA 508 Class 3 강용접부 및 열영향부 모사 시험편에 대해서 초음파공명분광법으로 동적탄성계수를 측정하였다. 등방성 탄성계수를 가정하여 초기 추정 탄성 계수, $c_{11},\;c_{12}$ 및 $c_{44}$로부터 장방형 시편의 공명 주파수를 계산하였으며 계산된 주파수와 초음파공명분광법으로 측정된 주파수를 비교, 반복 수렴 절차를 거쳐 정밀한 탄성계수를 구했다. 열처리 조건의 차이 및 미세 조직의 차이에 따라 영률 및 전단 계수의 차이가 확실하게 나타났다. 미세한 베이나이트 조직에서의 영률 및 전단 계수는 조대한 마르텐사이트 조직보다 높았으며 이러한 경향은 미세 경도 시험 등의 다른 실험 결과와도 일치하였다.

• 플랜트 저널
• /
• 제10권2호
• /
• pp.48-59
• /
• 2014

본 연구에서는 고온 고압 배관용 단조밸브 용접부의 품질확보를 위하여 단조밸브 제작현장에서 활용할 용접후열처리의 유지시간 및 유지온도를 연구했다. ASTM A182 F92 재료를 단조밸브의 용접부에 해당되는 밸브 끝단부 및 누설방지용접부와 동일한 형상의 두께 1 inch 쿠폰으로 가공하고, 쿠폰을 가스 텅스텐 아크용접(GTAW: Gas Tungsten Arc Welding) 방법으로 완전용입 용접하여 시편을 제작했다. 용접부 호칭두께가 1 inch인 시편을 $705^{\circ}C$, $735^{\circ}C$, $750^{\circ}C$, $765^{\circ}C$, $795^{\circ}C$ 및 $825^{\circ}C$에서 1시간 유지하여 용접후열처리를 실시(Group 1)하였다. 그리고 용접부 호칭두께가 1 inch인 시편 3개를 $735^{\circ}C$에서 30분, 1시간 및 2시간으로 달리 유지(Group 2)하여 용접후열처리를 실시하였다. 다른 유지시간과 유지온도에 따른 경도의 변화를 관찰하기 위하여 모재부, 열영향부 및 용착금속부에서 경도를 측정하였다. 본 실험의 결과에 따라, 1 inch당 1시간 온도를 유지할 경우는 용접후열처리가 $750^{\circ}C{\sim}765^{\circ}C$에서 수행되어야 바람직한 것으로 확인되었다. 단조밸브 제작규격에서 요구하는 최소 유지온도 보다 $5^{\circ}C$가 높은 $735^{\circ}C$에서 1 inch당 1시간 유지할 경우에 요구된 경도 값을 만족하지 못하여, 요건보다 긴 시간인 1 inch당 2시간 용접후열처리 시 경도 값을 만족하는 것으로 확인되었다. 또한 용착금속부의 조직은 템퍼드-마르텐사이트 조직으로 확인되었다.

• 대한금속재료학회지
• /
• 제49권8호
• /
• pp.628-634
• /
• 2011

SA508 Gr.4N Ni-Cr-Mo low alloy steel, in which Ni and Cr contents are higher than in commercial SA508 Gr.3 Mn-Mo-Ni low alloy steels, may be a candidate reactor pressure vessel (RPV) material with higher strength and toughness from its tempered martensitic microstructure. The inner surface of the RPV is weld-cladded with stainless steels to prevent corrosion. The goal of this study is to evaluate the microstructural properties of the clad interface between Ni-Cr-Mo low alloy steel and stainless weldment, and the effects of post weld heat treatment (PWHT) on the properties. The properties of the clad interface were compared with those of commercial Mn-Mo-Ni low alloy steel. Multi-layer welding of model alloys with ER308L and ER309L stainless steel by the SAW method was performed, and then PWHT was conducted at $610^{\circ}C$ for 30 h. The microstructural changes of the clad interface were analyzed using OM, SEM and TEM, and micro-Vickers hardness tests were performed. Before PWHT, the heat affected zone (HAZ) showed higher hardness than base and weld metals due to formation of martensite after welding in both steels. In addition, the hardness of the HAZ in Ni-Cr-Mo low alloy steel was higher than that in Mn-Mo-Ni low alloy steel due to a comparatively high martensite fraction. The hardness of the HAZ decreased after PWHT in both steels, but the dark region was formed near the fusion line in which the hardness was locally high. In the case of Mn-Mo-Ni low alloy steel, formation of fine Cr-carbides in the weld region near the fusion line by diffusion of C from the base metal resulted in locally high hardness in the dark region. However, the precipitates of the region in the Ni-Cr-Mo low alloy steel were similar to that in the base metal, and the hardness in the region was not greatly different from that in the base metal.