• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.5
• /
• pp.1524-1533
• /
• 1996

Risidual stress of cylindrical glass rods are measured by photoelasticity to study the variation of stresses with respect to heat treatment temperatures. In order to measure the stresses accurately, fringe sharpening and multiplication techniques are applied to the determination of photoelastic fringe orders. Filon's separationmethod is used to resolve circumferential and redial stress ocmponents from isochromatic fringes which are the same as in-plane maximum shearing stresses. According to the photoelastic measurements, residual stress is increased as the heat treatment temperature of the rods is raised from $560^{\circ}C$ to $650^{\circ}C$ All the circumferential stress components are changed from tensile stresses to compressive ones at approximate $R_m$/$R_o$ = 0.6, where $R_o$/ is outer radius and $R_m$any measured radius. This analysis shows that residual stresses of the glass rods approach zero if the rods are heat-treated near the strain point.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.87-92
• /
• 2000

This study is to investigate the heat transfer characteristics the for a round turbulent jet impinging on the flat plate with and without rib. Liquid crystal/transient method was used to determine the Nusselt number distributions along the surface. The temperature on the surface was measured using liquid crystal and a digital color image processing system. The experiments were made fur the jet Reynolds number (Re) 23,000, the dimensionless nozzle-to-surface distance (L/d) from 2 to 10, and the rib type [height ($d_1$) 2mm, pitch (p) from 12 to 36mm]. It was found that for $L/d{\ge}6$ the average Nusselt numbers on the flat plate with rib type C ($p/d_1=16$) are higher than those without rib, mainly due to an increase in the turbulent intensity caused by flow separation, recirculation and reattachment on the wall surface.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.124-130
• /
• 2001

The heat transfer and flow measurements were made on a cylindrical pedestal mounted on a flat plate with a turbulent impinging air jet. The heat transfer coefficient distributions on the flat plate were measured using the shroud-transient technique and liquid crystal was used to measure the surface temperature. The jet Reynolds number (Re) is 23,000, the dimensionless nozzle-to-surface distance (L/d) from 2 to 10, the dimensionless pedestal diameter-to-height (H/D) from 0 to 1.5, the dimensionless 2nd pedestal diameter-to-height ($H/D_2$) from 0 to 0.4 and the distance from the stagnation point to 2nd pedestal (p/D). The results show that for H/D = 0.5 to 1.5, the Nusselt number distributions on the plate surface exhibit a maximum between $r/d\;{\cong}\;1.0$ and 1.5. The presence of the pedestal appears to cause the flow separation and reattachment on the plate surface, which results in the maximum heal transfer coefficient. Also, for p/D = 2.5 and $H/D_2$ = 0.3, the local Nusselt number in the region corresponding to $r/d\;{\cong}\;1.1$ was increased up to 50% compared to that for $H/D_2=0$.

• Applied Chemistry for Engineering
• /
• v.24 no.4
• /
• pp.337-343
• /
• 2013

Membrane reactors have been showing a promising future and attracted increasing attention in the scientific community as they possess advantages in terms of enhanced catalytic activity and selectivity, combination of processes (reaction and separation), simplicity in process design, and safety in operation. In particular, solid electrolyte membrane reactor principles are realized in fuel cells, electrolyzers and reactors for hydrogenation of carbon dioxide and other economically viable reactions. In this review, as a young generation of ion conducting materials, high temperature proton conductors are discussed in terms of the current status of material development and their various applications.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.381-386
• /
• 2007

Jet-A spray, evaporation and combustion were numerically analyzed in annular type model combustor using KIVA-3V. Liquid fuel's atomizing was affected by flow field near droplet. When cooling flow was not optimized, SMD was increased, and equivalence ratio was horizontally distributed in combustor's downstream. Flame spread out horizontally and separated in combustors downstream. Flame center was separated by cooling flow. Flame separation made local high temperature in downstream that caused NO increase.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.225-229
• /
• 2001

There are about 41% (by weight) of scrap tires were pulverized to produce rubber powder and granules in the tire recycling industry of Taiwan. However, the reuse of the by-products, steel and fiber, of the scrap tires still needs to be improved. It is difficult to remove the remaining rubber on the surface of steel or fiber. This problem reduce the availability for further reuse of steel and fiber. In addition to the improvement of magnetic, gravity separation techniques or carbonization process, using cryogenic shredding process to separate rubber and fiber (or steel) had been used as another alternative. Cryogenic shredding process for scrap tires showed many advantages, the objective of this paper is to explore the mechanisms for the cryogenic shredding process of scrap tires. Cryo-SEM is used to investigate the topographic information, in-situ, from room temperature to -195$^{\circ}C$ . One square inch shredded tire chips are prepared for SEM study. The percentage of the shrinkage of rubber is also estimated, ca. 6.7%. Mechanisms of cryogenic shredding effects on the tire chips are discussed. The proper practice of cryogenic shredding process far scrap tires is also suggested.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.9-18
• /
• 2001

1. EAF Dust in Japan - Generation and Characteristics. The quantity of dust generated from EAF shops in Japan was estimated to be 520,000 tons/year in 1999. Extremely fine dust (or fume) is formed in the EAF by metal vaporization. Its characteristics such as chemical compositions, phases, particle size, leaching of heavy metal are mentioned. 2. EAF Dust Treatment Methods in Japan. In 1999, 61% of EAF dust was treated by regional zinc recovery processing routes, 25% went to landfill disposal, 4% was reused as cement material, and 10% was treated by on-site processing routes. The problems of EAF dust treatment methods in Japan are: (1) very high treatment cost, and (2) heavy environmental load (leaching of heavy metal, emission of dioxins, depletion of disposal sites, etc). It has been much hoped for that new dust management technology would be developed. 3. New technology of EAF dust treatment in Japan. In Japan, some new technologies of EAF dust treatment have been developed, and some others are in the developing stages. Following five processes are mentioned:. (1) Smelting reduction process by Kawasaki Steel, (2) DSM process by Daido Steel, (3) VHR process by Aichi Steel, (4) On-site dust direct recycling technology, and (5) Process technology of direct separation and recovery of iron and zinc metals contained in high temperature EAF off gas by the Japan Research and Development Center fur Metals.

• Korean Journal of Pharmacognosy
• /
• v.7 no.1
• /
• pp.3-13
• /
• 1976

The hitherto existing gap in the field of chromatographic methods has been filled by the direct coupling of a suitable oven (TAS-oven) with TLC. The sample to be examined is heated either isothermally or linearly within the temperature gradient of $50{\sim}450^{\circ}C$. The volatile and/or thermolytically evolved substances are fractionated on the TLC-layer and subsequently chromatographed under standard conditions. Transport mechanisms from the sample to the TLC-layer, applications of the TAS-procedure and further developments are discussed. Thermofractography, developed from the TAS-procedure, is demonstrated on different groups of natural substances such as alkaloids, amino acids, nucleic acids. nucleosides, nucleotides, triglycerides and other lipids, pyrone glycosides and aglycon. Experimental work and results on the thermolysis of macromolecular natural and synthetic substances, natural polyphenols, tanning agents and leather and the possibilities of differentiating various lignins, carbohydrate and synthetic polymers are reported. Further, it is shown that classical reactions in the microgram range, e.g. zinc dust distillation, sulphur-and selenium dehydrogenation and catalytic dehydrogenation, can be coupled directly with TLC. Also described is a method which allows to investigate the gaseous compounds evolved during thermofractography in the range of up to $450^{\circ}C$. Thermal procedures coupled with TLC open up the following new possibilities for chemical microanalysis: fractionated separation of distillable and sublimable components, fractionated thermolysis and carrying out of thermal reactions in the ultra micro range.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.642-645
• /
• 2007

석탄, 폐기물 등 다양한 시료의 가스화 반응을 통해서 발생되는 합성가스는 CO, $H_2$, $CO_2$가 주성분으로 가스엔진, 가스터빈 등의 연료로 사용하여 발전하거나 합성반응을 통해 다양한 화학원료로의 전환이 가능하다. 합성가스를 가스엔진, 가스터빈, 연료전지등의 연료로 사용하는 경우는 고효율 발전이 가능하여 기존 연소방식의 발전과 비교하여 단위 전력 생산량 당 $CO_2$의 배출량이 감소 되며, 여기에 $CO_2$ 분리공정을 적용하면 $CO_2$ 배출량 감소효과를 극대화 할 수 있다. 화석연료의 연소 및 가스화 반응을 통해서 발생하는 이산화탄소의 분리에 대한 많은 연구가 진행되고 있으나, 본 연구에서는 흡착방식을 이용한 합성가스 내의 이산화탄소 분리를 위하여 흡착제를 이용한 이산화탄소의 흡착, 탈착 성능 분석 연구를 수행하였다. 합성가스내의 이산화탄소를 분리하기 위한 흡착제로는 NaX 계열의 zeolite를 이용하였으며, 가스화 반응을 통해 발생한 합성가스를 흡착제에 통과시켜 이산화탄소의 선택적 흡착 여부를 확인하였다. 또한 TPD(Temperature Programmed Desorption)방법을 이용하여 흡착제의 이산화탄소 흡착 성능을 분석하였다.

• Journal of Technologic Dentistry
• /
• v.25 no.1
• /
• pp.21-28
• /
• 2003

The purpose of this study was to process bio-active glass ceramic composite, reinforced with sapphire fibers, by hot press. Also to study the interface of the matrix and the sapphire fiber, and the mechanical properties. Glass raw materials melted in Pt crucible at 1300$^{\circ}C$ during 3.5 hours. The melt was crushed in ball mill and then crushed material, ground and sieved to $<40{\beta}{\mu}m$. Sapphire fibers cut (30mm) and aligned. Powder and fibers hot pressed. The micrographs show good bonding between the matrix and the fiber and no porosity in the glass matrix. This means ideal fracture phenomena. Glass is fractured before the fiber. This is indication of good fracture strength. EDXS showing aluminum rich phase and crystalline phase. Bright field image of the matrix showing crystalline phase. Also diffraction pattern of TEM showing the crystalline phase and more than one phase. Strength of the samples was determined by 3 point bend testing. Strength of the 10vol% sample was approximately 69MPa, while strength of the control sample is 35MPa. Conclusions through this study as follow: 1. Micrographs show no porosity in the glass matrix and the interface. 2. The interface between the fiber and the glass matrix show no gaps. 3. Fracture of the glass indicates characteristic fiber-matrix separation. 4. Presence of crystalline phase at high processing temperature. 5. Sapphire is compatible with bioactive glass.