• 한국세라믹학회지
• /
• 제43권11호
• /
• pp.673-679
• /
• 2006

The discovery of ferroelectric barium titanate (BaTiO$_3$) in 1942 began the present era of dielectrics-based electronic ceramics. Ferroelectric barium titanate has a high dielectric constant and after the recognition of BaTiO$_3$ as a new ferroelectric compound, various attractive electrical properties have been extensively studied and reported. Since then, pioneering work on valence-compensated semiconduction led to the discovery of the positive temperature coefficient (PTC) of the resistance effect found in doped BaTiO$_3$. Significant progress has since followed with respect to understanding the PTC phenomena, advancing materials capabilities, and developing devices for sensor and switching applications. In this paper, the theoretical aspects of the various PTC models are discussed and the future trends of practical applications for PTC devices are briefly mentioned.

• Tribology and Lubricants
• /
• 제16권3호
• /
• pp.166-172
• /
• 2000

The friction and wear characteristics of dental composite resins such as Charisma, Elitefil, TPH and Veridonfil were investigated. Furthermore, The surface characteristics examination, the analysis of contents of filler, Victors hardness and fracture toughness measurement of composite resins were preformed. The wear test applied ball to move reciprocationally on flat wear tester at room temperature. Microstructure of surfaces and worn surfaces were observed by SEM. Experimental results indicate that the friction coefficient of TPH was quite low, and the wear resistance of TPH was better than that of Charisma, Elitefil or Veridonfil at the same condition. The main wear mechanism was found to be plastic flow and abrasive wear by failure of filler's bond to the matrix.

• 대한전자공학회논문지
• /
• 제23권3호
• /
• pp.364-369
• /
• 1986

Silicon diaphragms, 10 and 20 \ulcorner-thick and 1x1 mm\ulcornerarea, have been fabricated by means of the electrochemical P-N junction etch-stop technique. The P-type diffused resistors were formed on the diaphragm, and the piezoresistance effect was examined. It was been found that the fractional variation of the resistance is dependent on the diaphragm thickness, resistor location, and resistor length, etc. The 1.2 k\ulcornerfull-brige pressure sensor with 10\ulcorner-thick diaphragm exhibits a pressure sensitivity of 42 \ulcorner/V\ulcornermHg with a temperature coefficient of 2.3 mmHg/\ulcorner, and shows a good linearity in the pressure range from 0 to 300 mmHg.

• Computers and Concrete
• /
• 제15권5호
• /
• pp.847-864
• /
• 2015

In this paper, a reaction-diffusion model of carbonation process in self-compacting concrete (SCC) was realized with a consideration of multi-field couplings. Various effects from environmental conditions, e.g. ambient temperature, relative humidity, carbonation reaction, were incorporated into a numerical simulation proposed by ANSYS. In addition, the carbonation process of SCC was experimentally investigated and compared with a conventionally vibrated concrete (CVC). It is found that SCC has a higher carbonation resistance than CVC with a comparable compressive strength. The numerical solution analysis agrees well with the test results, indicating that the proposed model is appropriate to calculate and predict the carbonation process in SCC. The parameters sensitivity analysis also shows that the carbon dioxide diffusion coefficient and moisture field are essentially crucial to the carbonation process in SCC.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1993년도 추계학술대회 논문집
• /
• pp.25-28
• /
• 1993

In this study, the dielectric properties of (Sr$\sub$1-x/Ca$\sub$x/)TiO$_3$+yNb$_2$O$\sub$5/(0.1 x 0.3, 0.004 y 0.008) ceramic capacitor were investigated. The specimen was sintered for 3hr at 1350$^{\circ}C$ in gas(N$_2$) atmosphere. The reduced specimen fared at 1200$^{\circ}C$ in air. The used specimens had the apparent permittivity of 3${\times}$10$^4$∼4${\times}$10$\^$5/, tan$\delta$ of 0.05 -0.2, and insulating resistance of 10$\sub$9/∼10$\^$12/ $\Omega$.cm. The specimens had the stable temperature coefficient of capacitance.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.13-20
• /
• 1995

To develope a high precision TiAIN thin film resistor, TiAIN films were deposited on A1$_{2}$03 substrates by reactive planar magnetron cosputtering from Ti and Al targets in an Ar-N$_{2}$ atmosphere. The characteristics of the TiAIN thin film were controlled by changing of the R.F. power on Ti and Al targets, and the N$_{2}$ partial pressure. The high precision TiAIN thin film resistor with TCR(Temperature Coefficient of Resistance) of less than 10ppm/.deg. C was obtained under the R.F. power condition of 160(w)/240(w) to Ti and Al targets at the N$_{2}$ partial pressure of 7*10$^{-5}$ Torr. The composition of these films were investigated by XRD, SEM and EDS.

• 대한기계학회논문집B
• /
• 제24권3호
• /
• pp.419-425
• /
• 2000

Multiple layer of wire screen is widely used in many compact devices to filter particulates and to heat or cool fluids. However, data of flow resistance and heat transfer through such layers are rare to find and thus they are experimentally investigated in this study. Compressed air is made to flow through it to find the Ergun constants over a wide range of the Reynolds number. Also, unsteady heating of the wire screen is performed to find the equivalent heat transfer coefficient between the screen and the air by fitting the unsteady air temperature. The obtained coefficients are expressed in terms of the Reynolds number and the Prandtl number.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.124-130
• /
• 1998

The wear characteristics and wear mechanisms of dental composite resins were investigated. Composite resins such as Metalii, Silux Plus, Heliomolar and Palfique Estelite were selected as specimens and contents of filler in specimens in order to analyze the effect of Prepolymerized Particle Fillers in friction and wear characteristics. Ball on flat wear tester was used for a wear test. Friction and wear tests are carried out at room temperature. The friction coefficient of Metafil was quite high relatively, and the wear resistance of Silux Plus and Palfique Estelite was better than that of Metafil and Hellomolar at the same experimental condition. The main wear mechanism is plastic flow and abrasive wear by crack propagation.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 1999년도 추계 학술발표회 논문집
• /
• pp.211-216
• /
• 1999

One of the problems in a refrigerator operation is the frost formation on a cold surface of the evaporator. The frost layer is formed by the sublimation of water vapor when the surface temperature is below the freezing point. This frost layer is usually porous and formed on the cold surface of the evaporator. The frost layer on the surface of a evaporator will make side effect such as thermal resistance. However, these important factors have not been used in determining the defrosting period. In this report, a prediction taking into account the change of the fin efficiency due to the growth of the frost layer.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 춘계학술발표회 초록집
• /
• pp.1-1
• /
• 2000

The results of the modification of metal materials treated by high temperature pulst:d plasma fluxes (HTlPPF) with a specific power of incident flux changing in the $(3...100)10^5{]\;}W/cm^2$ range and a pulse duration lying from 15 to $50{\;}\mu\textrm{s}$ have been presented. The results of HTPPF action were studied on the stainless steels of 18Cr-l0Ni, 16Cr- 15Ni, 13Cr-2Mo types; on the structural carbon steels of (13...35)Cr, St. 3, St. 20, St. 45 types; on the tool steels of U8, 65G, ShHI5 types, and others; on nickel and high nickel alloy of 20Cr-45Ni type; on zirconium- and vanadium-base alloys and other materials. The microstructure and properties (mechanical, tribological, erosion, and other properties) of modified materials and surface alloying of metals exposed to HTPPF action have been investigated. It was found that the modification of materials by HTPPF resulted in a simultaneous increase of several properties of the treated articles: microhardness of the surface and layers of 40...60 $\mu\textrm{m}$ in depth, tribological characteristics (friction coefficient, wear resistance), mechanical properties ({\sigma_y}, {\;}{\sigma_{0.2}}.{\;}{\sigma_r}) on retention of the initial plasticity ($\delta$), corrosion resistance, radistanation erosion under ion irradiation, and others. The determining factor of the changes observed is the structural-phase modification of the near-surface layers, in particular, the formation of the fine cellular structure in the near-surface layers at a depth of $20{\;}{\mu\textrm{m}}$ with dimension of cells changing in the range from 0.1 to $1., 5{\;}\mu\textrm{m}$, depending on the kind of material, its preliminary treatment, and the parameters of plasma fluxes. The remits obtained have shown the possibility of purposeful surface alloying of metals exposed to HTPPF action over a depth up to 20...45 $\mu\textrm{m}$ and the concentration of alloying element (Ni, Cr, V) up to 20 wt.%. Possible industrial brunches for using the treatment have been also considered, as well as some results on modifying the serial industrial articles by HTPPF.