• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.11
• /
• pp.2038-2042
• /
• 2010

In this paper, we confirmed the thermal & optical properties for improving the heat transfer coefficient by changing the via hole size and in FR4 PCB with the same area. Osram 1W power LED Package (Golden Dragon) was used and the K-factor which is relative constant between LED junction temperature and forward bias was measured with power source meter(KEITHLEY 2430) to measure the thermal resistance from PCB configuration. As results, thermal resistance in metal PCB came out to the lowest as $26 [^{\circ}C/W]$ and thermal resistance in FR4 PCB without via-holes emerged as the highest as $69 [^{\circ}C/W]$. However thermal resistance of FR4 PCB could have decreased until $32[^{\circ}C/W]$ in 0.6 mm by using the via hole. Also, the luminous flux could have improved, too.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.1
• /
• pp.59-62
• /
• 2017

CNT (carbon nanotube) resistors with low resistance and negative TCR (temperature coefficient of resistance) were fabricated with yarned CNT (carbon nanotube) fibers. The CNT fibers were prepared by yarning CNTs grown on the silicone substrate by CVD (chemical vapor deposition) method. The CNT resistors were fabricated by winding CNT fibers on the surface of ceramic rod. Both metal terminals were connected with the CNT fiber wound on the ceramic rod. We measured electrical resistance and thermal stability with the number of CNT fibers wound. The CNT resistor system shows linearly decreased resistance with the number of CNTs wound on the ceramic rod and saturated at 20 strands. The CNT resistor system has negative TCR between $-1,000{\sim}-2,000ppm/^{\circ}C$ and stable frequency properties under 100 kHz.

• Journal of the Korean Ceramic Society
• /
• v.28 no.10
• /
• pp.803-809
• /
• 1991

Microstructure, room temperature resistivity and temperature coefficient of resistance of BaTiO3 ceramics were characterized and measured in this study. The basic composition of the BaTiO3 cremics was formed by adding 0.25 mol% Dy2O3 and 0.07 mol% MnO2 to the BaTiO3 composition. Samples of the BaTiO3 ceramics were prepared by adding various amounts of the TiO2, SiO2 and Al2O3 to the basic composition. An addition of 1 mol% TiO2, 2 mol% SiO2 and 0.5 mol% Al2O3 to the basic composition resulted both the values of the room temperature resistivity and the temperatured coefficient being maxium. Meanwhile, an addition of 1 mol% TiO2 and 1 mol% Al2O3 to the basic composition resulted the value of the room temperature resistivity maxium and the temperature coefficient minimum. The temperature coefficient showed a maximum value as well as a minimum value when the three kinds of the additives were added together to the basic composition of the BaTiO3 ceramics. Maxed phases of BaTi3O7, BaTiSiO5 and BaAl2Si2O8 were present at the grain boundary.

• International Journal of Korean Welding Society
• /
• v.2 no.1
• /
• pp.1-10
• /
• 2002

The thermal contact conductance at different temperatures and with different electrode forces and zinc coating morphology was measured by monitoring the infrared emissions from the one dimensionally simulated contact heat transfer experiments. The contact heat transfer coefficients were presented as a function of the harmonic mean temperature of the two contacting surfaces. Using these contact heat transfer coefficients and experimentally measured temperature profiles, the electrical contact resistivities both for the faying interface and electrode-workpiece interface were deduced from the numerical analyses of the one dimension simulation welding. It was found that the average value of the contact heat transfer coefficients for the material with zinc coating (coating weight from 0 g/$mm^2$to 100 g/$mm^2$) ranges from 0.05 W/$mm^2$$^{\circ}C$ to 2.0 W/$mm^2$$^{\circ}C$ in the temperature range above 5$0^{\circ}C$ harmonic mean temperature of the two contacting surfaces. The electrical contact resistivity deduced from the one dimension simulation welding and numerical analyses showed that the ratio of electrical contact resistivity at the laying interface to the electrical contact resistivity at the electrode interface is smaller than one far both bare steel and zinc coated steel.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.3
• /
• pp.219-222
• /
• 2019

In this study, we fabricated plate-type shunt resistors with thermal stability by parallelly connecting metal alloy plates with positive temperature coefficient of resistance (TCR) and carbon nanotube (CNT) plates with negative TCR. The metal alloy plates, which were prepared by alloying Cu and Mn with a composition of 91 wt% of Cu and 9 wt% of Mn, showed around $800ppm/^{\circ}C$ of TCR, and the CNT plates prepared from the CNT solution by using the vacuum filtration method showed around $-800ppm/^{\circ}C$ of TCR. The shunt resistor that was fabricated by stacking metal alloy plates and CNT plates in this work showed about $46.93ppm/^{\circ}C$ of TCR. Therefore, we conclude that a shunt resistor with low TCR can be realized by simply adjusting the TCR of the metal alloy only, because the TCR of the CNT plate has an identical value.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.6
• /
• pp.520-526
• /
• 2007

In order to acquire fundamental informations to fabricate high precision thin film resistors, NiCr/NiCrSi alloy films were prepared using Ni and Cr targets. Effect of composition on the electrical properties of the NiCr/NiCrSi alloy film were then investigated. Considering the effect of Si doping on the electrical and material characteristics, the lower TCR (temperature coefficient of resistance) values could be achieved for samples with Ni/Cr ratio of $0.8{\sim}1.5$ (in a range of relative higher specific resistivity and Cr composition of $40\;wt%{\sim}55\;wt%$) and with Si doping. Consequently, the sample prepared using a DC power showed a good TCR of $-25\;ppm/^{\circ}C$, which implies that increase of specific resistivity and decrease of TCR would be achieved more efficiently not for Ni-Cr binary material but for Si doped Ni-Cr ternary material, and not using RF power but using DC power in the sputtering process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.339-339
• /
• 2013

We study on the optical and electrical properties of indium-free ZTO(ZnSnO)/Ag/ZTO (ZAZ) multilayer electrodes for the low-cost transparent electrode. In the first step, each single layer was deposited using rf magnetron in-line sputter with various working pressure based on $O_2$/$Ar+O_2$ ratio (0~3%) and power at room temperature. Secondly, we studied the optical and electrical properties by analyzing the refractive index, extinction coefficient, transmittance and resistivity of each layer. Finally, we optimized the thickness of each layer using macleod simulation program based on the analyzed optical properties and fabricated the multilayer electrode. As a result, We achieved a low sheet resistance of $11{\Omega}$/sq and anaverage transmittance of 80% in the visible region of light (380~780 nm). This indicates that indium-free ZAZ multilayer electrode is a promising low-cost and low-temperature processing electrode scheme.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1236-1238
• /
• 1994

TiAlN thin films were prepared by a multi target r.f magnetron sputtering system under different conditions. We have investigated the resistivity and T.C.R. (Temperature Coefficient of Resistance) characteristics of TiAlN films deposited on $Al_2O_3$ and glass substrates by sputtering in an $Ar:N_2$ gas mixture. We used Al and Ti metal as Target Material and $Ar:N_2$ gas as working gas. We varied the partial pressure ratio of $N_2/Ar$ from 0.2/7 to 1.0/6.2 (SCCM). And the R.F power of Ti and Al Target also were varied as 160/240, 200/200 and 240/160(W). In this experiment, we can get the precision thin film resistor with a very low T.C.R. (Temperature Coefficient of Resistance) below 25 ppm ${\Omega}/^{\circ}C$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.6
• /
• pp.155-165
• /
• 1998

The resistance coefficient and heat transfer performance are studied for the turbulent water flow in a smooth coiled tube having variable curvature ratios and a corrugated-coiled tube having a ratio of coil to tube diameter of 22. Experiments are carried out for the fully developed turbulent flow of water in tube coils on the uniform wall temperature condition. This work is limited to tube coils of R/a between 22 and 60 and Reynolds numbers from 13000 to 53000. The tube having a ratio of coil to tube diameter of 27 among the 3 smooth tube coils shows the best heat transfer performance. A corrugated-coiled tube(R/a=60) shows more excellent performance than a smooth coiled tub (R/a=60) at a similar curvature ratio. The friction factor f is sensitive to changes in the velocity profile caused by a temperature gradient. Allowance was made for the pressure loss in the short inlet and outlet lengths and due to the presence of the thermocouple inlet and outlet as a result of separate experimental on a straight tube. It is to be expected that the allowance at the exit will be somewhat too low because of secondary flow effects carried over from the coil.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.73.1-73.1
• /
• 2010

For the successful cold starting of a fuel cell engine, either internal of external heat supply must be made to overcome the formation of ice from water below the freezing point of water. In the present study, switchable vanadium oxide compounds as variable temperature-electrical resistance materials onto the surface of flat metallic bipolar plates have been prepared by a dip-coating technique via an aqueous sol-gel method. Subsequently, the chemical composition and micro-structure of the polycrystalline solid thin films were analyzed by X-ray diffraction, X-ray fluorescence spectroscopy, and field emission scanning electron microscopy. In addition, it was carefully measured electrical resistance hysteresis loop over a temperature range from $-20^{\circ}C$ to $80^{\circ}C$ using the four-point probe method. The experimental results revealed that the thin films was mainly composed of Karelianite $V_2O_3$ which acts as negative temperature coefficient materials. Also, it was found that thermal dissipation rate of the vanadium oxide thin films partially satisfy about 50% saving of the substantial amount of energy required for ice melting at $-20^{\circ}C$. Moreover, electrical resistances of the vanadium-based materials converge on an extremely small value similar to that of pure flat metallic bipolar plates at higher temperature, i.e. $T{\geq}40^{\circ}C$. As a consequence, experimental studies proved that it is possible to apply the variable temperature-electrical resistance material based on vanadium oxides for the cold starting enhancement of a fuel cell vehicle and minimize parasitic power loss and eliminate any necessity for external equipment for heat supply in freezing conditions.