• Journal of Hydrogen and New Energy
• /
• v.7 no.2
• /
• pp.173-180
• /
• 1996

4-probe resistivity measurement technique was used to study kinetics of hydrogen absorption-desorption on Pd film($520{\AA}$ thick) at room temperature upto 1 bar. Kinetics data are fitted well to 1st order kinetics equation in ${\alpha}$ and ${\alpha}^{\prime}$ phases. In ${\alpha}+{\alpha}^{\prime}$ phase, absorption kinetics was very complicated, but it could be explained partially with nucleation and growth process. Ln(dR/dt) vs. time plot gives rate constant k value(R is resistance of sample, t is time). k value for absorption is $4^{-6}{\times}10^{-4}/sec$ in ${\alpha}$ phase. k is increasing upto $4^{\times}10^{-2}/sec$ as hydrogen pressure increasing in ${\alpha}^{\prime}$ phase. k is proportional to ln(Pop/Peq), where Peq is equilibrium plateau pressure and Pop is the opposing pressure. In contrast to bulk sample k value was decreasing with increasing number of A-D cycling in ${\alpha}^{\prime}$ phase absorption.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.1
• /
• pp.64-71
• /
• 2012

While a conventional ECS mainly consisted of an air cycle machine and heat exchangers, a new concept of a phase change heat exchanger was added to improve the transient performance of the ECS. As a result, an ECS modeling program including the phase change heat exchanger is newly developed to estimate its effect in various flight conditions such as take-off, maneuver, cruise, and landing. The simulation result regarding a virtual flight profile has confirmed the new ECS fulfilled the requirement by showing the temperature of the cooling air returned from the bay was always kept below $80^{\circ}C$. Through this study, the new ECS concept with PCHE was verified successfully.

• Geomechanics and Engineering
• /
• v.15 no.4
• /
• pp.997-1004
• /
• 2018

The brine leakage is a tough problem in artificial freezing engineering. This paper takes the common soft clay in Wujiang District as the study object, and calcium chloride solutions with six salinity levels were considered. The 'classic' cooling curve method was employed to measure the freezing point of specimens after freeze-thaw. Results indicate that four characteristic stages can be observed including supercooling, abrupt transition, equilibrium and continual freezing, strongly dependent on the variation of unfrozen water content. Two characteristic points were found from the cooling curves, i.e., freezing point and initial crystallization temperature. A critical value for the former exists at which the increment lowers. The higher the saline content approximately linearly, lower the freezing point. In the initial five cycles, the freezing point increases and then stabilizes. Besides, the degree of supercooling was calculated and its correlations with water, salt and freeze-thaw cycles were noted. Finally, an empirical equation was proposed for the relationship of freezing point and three main factors, i.e., water content, saline content and freeze-thaw cycles. Comparison of calculated and measured data proves that it is reliable and may provide guidance for the design and numerical analysis in frozen soil engineering.

• Journal of Welding and Joining
• /
• v.29 no.1
• /
• pp.46-51
• /
• 2011

TSV technology raises several reliability concerns particularly caused by thermally induced stress. In traditional package, the thermo-mechanical failure mostly occurs as a result of the damage in the solder joint. In TSV technology, however, the driving failure may be TSV interconnects. In this study, the thermomechanical reliability of TSV technology is investigated using finite element method. Thermal stress and thermal fatigue phenomenon caused by repetitive temperature cycling are analyzed, and possible failure locations are discussed. In particular, the effects of via size, via pitch and bonding pad on thermo-mechanical reliability are investigated. The plastic strain generally increases with via size increases. Therefore, expected thermal fatigue life also increase as the via size decreases. However, the small via shows the higher von Mises stress. This means that smaller vias are not always safe despite their longer life expectancy. Therefore careful design consideration of via size and pitch is required for reliability improvement. Also the bonding pad design is important for enhancing the reliability of TSV structure.

• The Korean Journal of Mycology
• /
• v.40 no.2
• /
• pp.78-85
• /
• 2012

URP primers that were derived from repetitive DNA sequence of rice weedy rice have been applied for producing PCR polymorphisms in different fungal species. URP-PCR protocol employed stringent PCR with high annealing temperature over $55^{\circ}C$ throughout the thermo-cycling reaction, giving high reproducibility. Under the PCR condition, Each single URP primer produced characteristic fingerprints from diverse genomes of different fungal species, indicating its universal applicability. URP-PCR has been accessed for applicability to various fungal species with 33 genus, 142 species and 1,489 isolates. Numerous related papers have demonstrated that URP-PCR profiles of fungal species are very useful for identifying fungal species at intra and inter species levels. The results were reviewed in this paper.

• Korean Chemical Engineering Research
• /
• v.55 no.4
• /
• pp.483-489
• /
• 2017

The loss of the sulfur cathode material through dissolution of the polysulfide into electrolyte causes a significant capacity reduction of the lithium-sulfur cell during the charge-discharge reaction, thereby debilitating the electrochemical performance of the cell. We addressed this problem by using a chemical and physical approach called reduction of polysulfide dissolution through direct coating functional inorganic (graphene oxide) or organic layer (polyethylene oxide) on electrode, since the deposition of external functional layer can chemically interact with polysulfide and physically prevent the leakage of lithium polysulfide out of the electrode. Through this approach, we obtained a composite electrode for a lithium-sulfur battery (sulfur: 60%) coated with uniform and thin external functional layers where the thin external layer was coated on the electrode by solution coating and drying by a subsequent heat treatment at low temperature (${\sim}80^{\circ}C$). The external functional layer, such as inorganic or organic layer, not only alleviates the dissolution of the polysulfide electrolyte during the charging/discharging through physical layer formation, but also makes a chemical interaction between the polysulfide and the functional layer. As-formed lithium-sulfur battery exhibits stable cycling electrochemical performance during charging and discharging at a reversible capacity of 700~1187 mAh/g at 0.1 C (1 C = 1675 mA/g) for 30 cycles or more.

• Journal of Powder Materials
• /
• v.23 no.4
• /
• pp.317-324
• /
• 2016

Tin is one of the most promising anode materials for next-generation lithium-ion batteries with a high energy density. However, the commercialization of tin-based anodes is still hindered due to the large volume change (over 260%) upon lithiation/delithiation cycling. To solve the problem, many efforts have been focused on enhancing structural stability of tin particles in electrodes. In this work, we synthesize tin nano-powders with an amorphous carbon layer on the surface and surroundings of the powder by electrical wire explosion in alcohol-based liquid media at room temperature. The morphology and microstructures of the powders are characterized by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and transmission electron microscopy. The electrochemical properties of the powder for use as an anode material for lithium-ion battery are evaluated by cyclic voltammetry and a galvanometric discharge-charge method. It is shown that the carbon-coated tin nano-powders prepared in hexanol media exhibit a high initial charge specific capacity of 902 mAh/g and a high capacity retention of 89% after 50 cycles.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.9
• /
• pp.114-121
• /
• 2004

Thermal design changes and analysis on the engineering model of Command Telemetry Unit(CTU) for a geostationary communications satellite arc performed for the purpose of developing an engineering qualification model. A thermal model is developed by using power consumption measurement values of each functional board and thermal cycling test results. In modeling heat dissipated EEE parts, heat dissipation is imposed evenly on the EEE part footprint area which is projected to the printed circuit board. All the EEE parts of CTU meet the requirement of their allowable temperature range when placed on the engineering qualification level of thermal vacuum environments in accordance with the proposed thermal design changes.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.8
• /
• pp.652-657
• /
• 2001

Vanadate glasses containing 10~20mol% glass former, P$_2$O$_{5}$ were prepared by melting the batch in platinum crucible and quenching on the copper plate. Li$_2$O-P$_2$O$_{5}$-V$_2$O$_{5}$ glass-ceramics having LiV$_3$O$_{8}$ were obtained by heat-treatment of this glass in crystallization temperature. The glass-ceramics showed singnificantly good capacity and long cycles life according to heating condition. In this paper, we described electrochemical properties during crystallization process and found the best crystallizaton condition of Li$_2$O-P$_2$O$_{5}$-V$_2$O$_{5}$ glass as cathode material. Li$_2$O-P$_2$O$_{5}$-V$_2$O$_{5}$ glass-ceramics heat-treated at 233$^{\circ}C$ for 3 hors showed good rechargeable capacity of 220mAh/g in the cycling range between 2.0 and 3.9V.en 2.0 and 3.9V.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.10
• /
• pp.2223-2226
• /
• 2009

Pristine and sulfur-doped (LiFe$PO_{3.98}S_{0.03}$) lithium iron phosphates were synthesized by a sol-gel method. The XRD pattern of the prepared materials suggested an orthorhombic structure with a Pnma space group and an absence of impurities. The Li/LiFe$PO_4$ or LiFe$PO_{3.98}S_{0.03}$ cells were employed for cycling studies at various temperatures (25, 50 and $60\;{^{\circ}C}$). In all cases, the Li/LiFe$PO_{3.98}S_{0.03}$ cell showed an improved performance with a stable discharge behavior of ~155 mA$hg^{-1}$. Nevertheless, pristine LiFeP$O_4$ cells presented poor discharge behavior at elevated temperatures, especially $60\;{^{\circ}C}$.