• 전기학회논문지
• /
• 제57권7호
• /
• pp.1213-1217
• /
• 2008

Poling is an important process in fabricating PZT ceramic devices such as filters and resonators and activates piezoelectricity to sintered PZT ceramics. Tolerance of the operating frequency of these devices is tightly required in applications. And a factor to attribute the tolerance is the temperature dependence of the resonance frequency of PZT ceramics. In this paper the relationship of poling strength and temperature dependence of resonance frequency of PZT specimens was studied. The $Pb(Zr_{0.53}Ti_{0.47})O_3$ ceramics were fabricated and the poling strengths were chosen to be 0.5, 1.5, 2.5 and 3.5 [kV/mm]. The dielectric constant of the specimen poled in poling strength 0.5 [kV/mm] was less than that of unpoled specimen and the specimen poled in higher electric field had the higher dielectric constant. (002) peak in X-ray diffraction patterns of the specimens increased as poling strength increased. And the change of resonance frequency of the specimens according to the variation of temperature was measured. Resonance frequency of all specimens increased as the temperature increased. The specimen poled in higher electric field had the smaller positive temperature coefficient of resonance frequency. The effect that temperature coefficient of resonance frequency becomes smaller is obtained when Zr mole in PZT composition equation increase. Controlling the poling strength is believed to be a method to adjust the temperature stability of resonance frequency of the PZT ceramic devices.

• Journal of the Korean Wood Science and Technology
• /
• 제32권3호
• /
• pp.8-14
• /
• 2004

Nondestructive evaluation (NDE) technique method using a resonance frequency mode was carried out for woodceramics produced at different carbonizing temperatures (600℃, 800℃, 1000℃, 1200℃, 1500℃) at the phenol resin impregnation rate of 70%, for three kinds of species (Pinus densifora, Pinus koraiensis, Larix leptolepis), respectively. There was a poor relationship between density and static bending MOR. However, close correlations were found between dynamic MOE_d and static bending MOR, and between static MOEs and MOR. Especially, the correlation coefficient was highest between MOE_d and static bending MOR. Therefore, the MOE_d using the resonance frequency mode is useful as a NDE method for predicting the MOR of woodceramics produced at different carbonizing temperatures.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.625-628
• /
• 1998

This paper presents the design method of a temperature stable stepped-impedance resonator using composite material. In this method temperature coefficient of dielectric constant $(\tau\varepsilon)$ and thermal expansion coefficient $(\alpha1)$ of dielectric material were considered. Ba(Zn1/3Nb2/3)O3 and CaZrO3 as composite material having opposite signs of temperature coefficient of dielectric constant were selected. The length of this resonator for the temperature stability of resonance frequency was calculated at 900MHz, 1.4㎓ and 1.9㎓. It was found that the ratio of the length of positive $\tau\varepsilon$ materal to the length of negative $\tau\varepsilon$ material is constant at various resonance frequencies.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.232-235
• /
• 1999

In this paper, We described the effect of $MoO_3$ Addition and firing temperature on the microwave dielectric properties of $BiNb0_4$ ceramics. The specimens prepared by conventional mixed method was addicted by 0 - 0.03 wt% $MoO_3$ and fired at 860 - $950^{\circ}$ for 3hr. Density increased when $MoO_3$ is below O.Olwt% but decreased when over O.Olwt%. $BiNb0_4$ ceramics addicted with CuO 0.03wt % and $MoO_3$ 0.01 wt% showed microwave dielectric properties, Dielectric constant 37.5, Quality factor[Qx$f_0$]5500, Temperature coefficient of resonance frequency 15ppm/$^{\circ}$

• 한국세라믹학회지
• /
• 제43권5호
• /
• pp.284-292
• /
• 2006

$MgTiO_3{\cdot}CaTiO_3{\cdot}SrTiO_3$ system ceramics (MCST) were synthesized to study the effect of Ca addition amount and Sr substitution on temperature coefficient of resonance sequency. Temperature coefficient of resonance frequency was slightly increased by small amount ($i.e.{\sim}5%$) of Sr substitution. In case of 50% to 75% addition amount of $MgTiO_3$, decrease of quality factor was not observed with increasing dielectric constant.

• Journal of Electrical Engineering and Technology
• /
• 제9권5호
• /
• pp.1719-1723
• /
• 2014

In this study, the microwave dielectric properties of nano spheroidization glass powders added $Ba(Zn_{1/3}Ta_{2/3})O_3$ ceramics prepared by solid state reaction have been investigated. Adding $(Ba_{0.4}Ca_{0.6})SiO_3$ nano spheroidization glass powders could effectively promote the densification even in the case of decreasing the sintering temperature. When the glass frit is 0.3 wt% and sintering is carried out at a temperature of $1500^{\circ}C$ for 6 hr, a temperature stable microwave dielectric ceramic could be obtained, which has a dielectric constant (${\varepsilon}_r$) of 30.2, a quality factor ($Q{\times}f_0$) of 124,000 GHz and a temperature coefficient of resonance frequency (${\tau}_f$) of $2ppm/^{\circ}C$.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.483-488
• /
• 2001

In the present study a numerical simulation is performed on a natural convection inside a square cavity with a vibrating wall. The study has been conducted varying the heat transfer rate, wall excitation frequency and also the orientation of the cavity. The temperature and velocities inside the cavity was observed and also, the heat transfer coefficients on the heating wall was seen. From the results, it can be seen that the temperature inside the cavity decreases when excited with the proper frequency and the heat transfer coefficient increased with cavity inclination angle, ${\theta}$. It is also found from the results that flow resonance is occurred near the inclination angle ${\theta}=90^{\circ}$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 춘계학술대회 논문집
• /
• pp.292-294
• /
• 1996

Dielectric properties were investigated at Mn doped 0.17($Ba_{0.53}$, $Pb_{0.47}$)0-$0.16Nd_2O_3$-$0.67TiO_2$ system in microwave frequency. It was observed that dielectric constant of 90.1, quality factor of 1320 (at 3.8GHz) and temperature coefficient of resonance frequency 2.3 ppm/$^{\circ}C$ for 0.5wt% Mn doped 0.17($Ba_{0.53}$, $Pb_{0.47}$)0-$0.16Nd_2O_3$-$0.67TiO_2$ system in sintering condition $1290^{\circ}C$/2hr. The quality factor increase due to the compensation effect of Mn ions yp to 0.5wt% and the decrease due to the interface relaxation effect. The temperature coefficient of resonance frequency increases to negative direction with increasing the amounts of Mn.

• Journal of the Korean Wood Science and Technology
• /
• 제41권5호
• /
• pp.466-473
• /
• 2013

Nondestructive evaluation (NDE) technique method using a resonance frequency mode was carried out for heat-treated wood under different conditions. The effect of heat treatment on the bending strength and NDE technique using the resonance frequency by impact hammer and force transducer mode for Korean paulownia, Pinus densiflora, Lidiodendron tulipifera and Betula costata were measured. The heat treatment temperature has been investigated at $175^{\circ}C$ and $200^{\circ}C$, respectively. There were a close relationship of dynamic modulus of elasticity and static bending modulus of elasticity to MOR. In all conditions, It was found that there were a high correlation at 1% level between dynamic modulus of elasticity and MOR, and static modulus of elasticity and MOR. However, the result indicated that correlation coefficient is higher in dynamic modulus of elasticity to MOR than that in static modulus of elasticity to MOR. Therefore, the dynamic modulus of elasticity using resonance frequency by impact hammer mode is more useful as a nondestructive evaluation method for predicting the MOR of heat-treated wood under different temperature and species conditions.

• Journal of the Korean Wood Science and Technology
• /
• 제42권2호
• /
• pp.130-137
• /
• 2014

Nondestructive evaluation (NDE) method by using a resonance frequency mode was carried out for ceramics made from particle boards with different phenol resin impregnation ratios (30, 40, 50, 60%) at carbonizing temperature of $800^{\circ}C$. The material for ceramics was Miscanthus sinensis var. purpurascens board. Dynamic modulus of elasticity increased with increasing impregnation ratio. There was a close relationship of dynamic modulus of elasticity and static bending modulus of elasticity to modulus of rupture (MOR). However, the result indicated that correlation coefficient is higher in dynamic modulus of elasticity to MOR than that in static modulus of elasticity to MOR. Therefore, the dynamic modulus of elasticity using resonance frequency by free vibration mode is more useful as a nondestructive evaluation method for predicting the MOR of ceramics made from Miscanthus sinensis var. purpurascens particle boards by different phenol resin impregnation ratios.