• 전기전자학회논문지
• /
• 제28권3호
• /
• pp.369-374
• /
• 2024

본 논문에서는 차세대 메모리 기술로 주목받고 있는 커패시터리스 디램(one-transistor DRAM, 1T-DRAM)을 소자의 설계 최적화에 대해 다룬다. 기존 커패시터기반 DRAM의 한계를 해결하고자, 비대칭 듀얼 게이트 구조를 사용하여 보유 시간 및 성능을 향상시키는 방향성을 제시한다. ZTC(Zero-temperature coefficient) 지점을 1.25 V로 설정하여 온도 변화에 따른 성능 저하를 최소화하였다. 다양한 온도(300K~400K)에서 전류-전압 특성을 분석하여, ZTC 지점에서의 메모리 특성이 온도에 안정적으로 동작하는 것을 확인하였으며, 고온에서도 신뢰성 있는 동작을 보장하는 설계가 가능함을 입증하였다. 이를 통해 1T-DRAM 소자는 높은 신뢰성과 고효율을 갖춘 메모리 기술로서, 차세대 메모리 소자 개발에 중요한 기여를 할 수 있다.

• 터널과지하공간
• /
• 제19권6호
• /
• pp.507-516
• /
• 2009

고준위 방사성 폐기물 처분장의 경우 폐기물의 방사성 붕괴에 의해 발열 현상이 나타나게 되며, 암반을 통한 열전달에 의해 처분장 주변 환경이 변화됨으로써 처분장의 안전성에 영향을 미칠 수 있다. 그러므로 처분장의 안전성 확보를 위해선 적절한 처분장 내 환기장치가 필요하다. 적절한 환기시스템의 구축을 위해서는 암반 열물성치와 처분장 내 열전달계수의 산정을 통한 컴퓨터 시뮬레이션 연구가 핵심이라고 할 수 있다. 이에 본 연구에서는 KAERI Underground Research Tunnel(이하 KURT) 내부 환경 인자(건습구온도, 암반표면온도, 대기압)들의 측정을 통해 열전달계수를 산정하는 것에 초점을 맞추었다. KURT 내부 우측 연구모듈의 막장 벽면에 길이 2 m, 용량 5 kw의 히터가 $90^{\circ}C$로 암반 내부를 가열하고 있는 히터구간의 열전달계수 산정 결과, 태양의 위치에 따른 처분장 외부 대기의 온도변화에 의해 열전달계수의 수치 변화가 최대 7.9% 발생하였으며, 평균 열전달계수 h는 약 4.533 W/$m^2{\cdot}K$의 수치를 나타내었다.

• 설비공학논문집
• /
• 제18권11호
• /
• pp.906-914
• /
• 2006

The present paper dealt with an experimental study of boiling heat transfer characteristics of R-290. Pressure gradient and heat transfer coefficient of the refrigerant flow inside horizontal smooth minichannel were obtained with inner tube diameter of 3.0 mm and length of 2,000 mm. The direct electric heating method was applied for supplying a heat to the refrigerant uniformly. The experiments were conducted with R-290 purity of 99.99%, at saturation temperature of 0 to $10^{\circ}C$, a mass flux range of $50{\sim}250kg/m^2s$, and a heat flux range of $5{\sim}20kW/m^2$. The heat transfer coefficients of R-290 increased with increasing mass flux and saturation temperature, wherein the effect of mass flux was higher than that of the saturation temperature. Heat flux has a low effect on the increasing of heat transfer coefficient. The heat transfer coefficient was compared with six existing heat transfer coefficient correlations. The Zhang et al.'s correlation (2004) gave the best prediction of heat transfer coefficient. A new correlation to predict the two-phase flow heat transfer coefficient was developed based on the Chen correlation. The new correlation predicted the experimental data well with a mean deviation of 11.78% and average deviation of -0.07%.

• 한국재료학회지
• /
• 제32권9호
• /
• pp.391-395
• /
• 2022

Research is being actively conducted on the continuous thin plate casting method, which is used to manufacture magnesium alloy plate for plastic processing. This study applied a heat transfer solidification analysis method to the melt drag process. The heat transfer coefficient between the molten magnesium alloy metal and the roll in the thin plate manufacturing process using the melt drag method has not been clearly established until now, and the results were used to determine the temperature change. The estimated heat transfer coefficient for a roll speed of 30 m/min was 1.33 × 10⁵ W/m²·K, which was very large compared to the heat transfer coefficient used in the solidification analysis of general aluminum castings. The heat transfer coefficient between the molten metal and the roll estimated in the range of the roll speed of 5 to 90 m/min was 1.42 × 10⁵ to 8.95 × 10⁴ W/m²·K. The cooling rate was calculated using a method based on the results of deriving the temperature change of the molten metal and the roll, using the estimated heat transfer coefficient. The DAS was estimated from the relationship between the cooling rate and DAS, and compared with the experimental value. When the magnesium alloy is manufactured by the melt drag method, the cooling rate of the thin plate is in the range of about 1.4 × 10³ to 1.0 × 10⁴ K/s.

• 한국표면공학회지
• /
• 제46권6호
• /
• pp.264-270
• /
• 2013

Effects of preoxidation on high temperature wear of piercing plug tool steel sliding against SA210C steel used for production of seamless tube have been studied using a pin-on-disc CETR tribometer, under applied normal load of 20 N at $900^{\circ}C$ in air. It was found in the preoxidized pin specimens of piercing plug tool steel that the coefficient of friction decreased to about 0.4 at an initial stage followed by showing nearly constant value of about 0.4 during high temperature wear testing. On the other hand, it was also found in the pin specimens without preoxidation that the coefficient of friction increased and fluctuated, ranging from about 0.3 to 0.6 during the tests until the running period of about 800 sec. The compact and continuous Fe-oxide layer was formed on the contact surface of the preoxidized pin specimens after high temperature wear testing followed by penetrating along the grain boundaries of coarse ferrite in the decarburized region beneath the oxide layer due to the lower hardness of the region.

• 한국세라믹학회지
• /
• 제35권2호
• /
• pp.123-128
• /
• 1998

Multilayer ceramic capacitors(MLCC) were prepared by laminating the layer of composition with dif-ferent Curie temperature to improve temperature coefficient in the Pb(Mg1/3Nb2/3)O3-PbTiO3 binary system. Green sheet was formed by tape casting using Pb(Mg1/3Nb2/3)O3-PbTiO3 and PbTiO3 synthesized with solid state reaction of PBO. Nb2O5 MgO and TiO2. Green sheet with electrode of 70Ag-30Pd was laminated under 300 kg/cm2 at 70$^{\circ}C$ and sintered at 1100$^{\circ}C$ for 2hr. Curie temperatues for MLCC with 10 layers of pure PMN and 0.9PMN-0.1PT were lowered to -22$^{\circ}C$ and 36$^{\circ}C$ respectively. MLCC with 7 layers of PMN and 3 layers of 0.9PMN-0.1PT showed nearly zero temperature coefficient of capacitance in the range of -20∼30$^{\circ}C$ and sum of dissipation factor of each layer.

• 설비공학논문집
• /
• 제16권11호
• /
• pp.1044-1050
• /
• 2004

The present study has been conducted to develop a heat pipe heat exchanger for middle-high temperature ranged from 300 to $600^{\circ}C$. Heat transfer rate, overall heat transfer coefficient and temperature effectiveness were investigated using a heat pipe heat exchanger with Dowtherm A as working fluid. Theoretical analysis was also conducted, and the followings were obtained: (1) Heat exchange rate increased as waste gas temperature supplied to evaporator and frontal velocity in condenser increased, (2) Overall heat transfer coefficient increased by $3{\sim}7\%$ as frontal velocity in evaporator and condenser increased, (3) Temperature effectiveness was about $30\%$ in evaporator and was about $40\%$ in condenser, (4) Heat recovery rate was about $38\%$, (5) Pressure drop did not exceed $8\;mmH_{2}O$ under the running condition of $1{\sim}3Nm/s$, (6) Simulation results were corresponded with experimental results.

• Macromolecular Research
• /
• 제12권1호
• /
• pp.53-62
• /
• 2004

We have prepared polymer composites of low-density polyethylene (LDPE) and ionomers (Surlyn 8940) containing polar segments and metal ions by melt blending with carbon black (CB) as a conductive filler. The resistivity and positive temperature coefficient (PTC) of the ionomer/LDPE/CB composites were investigated with respect to the CB content. The ionomer content has an effect on the resistivity and percolation threshold of the polymer composites; the percolation curve exhibits a plateau at low CB content. The PTC intensity of the crosslinked ionomer/LDPE/CB composite decreased slightly at low ionomer content, and increased significantly above a critical concentration of the ionomer. Irradiation-induced crosslinking could increase the PTC intensity and decrease the NTC effect of the polymer composites. The minimum switching current (Ι$\sub$trip/) of the polymer composites decreased with temperature; the ratio of Ι$\sub$trip/ for the ionomer/LDPE/CB composite decreased to a greater extent than that of the LDPE/CB composite. The average temperature coefficient of resistance (${\alpha}$$\sub$T/) for the polymer composites increased in the low-temperature region.

• 한국재료학회지
• /
• 제15권12호
• /
• pp.780-785
• /
• 2005

To investigate the microcrack healing behavior of $Si_3N_4-20wt\%SiC-8wt\%Y_2O_3$ composite ceramics(SNCY8), we observe the crack length evolution a! the time of 20, 40, 60 minutes with in-situ optical microscopy by varying healing temperature of $800\~1200^{\circ}C$. Crack healing obviously occurred as heating temperature and time increased. We proposed a simple model of effective diffusion based on the crack length evolution with healing condition, and determined the effective diffusion coefficient as Our result implies that we may predict the healing ability quantitatively with temperature and time in structural ceramics through the effective diffusion coefficient model.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.843-846
• /
• 2000

The (1-x)MgTiO$_3$-xSrTiO$_3$(x=0.02∼0.08) ceramics were fabricated by conventional mixed oxide method. The sintering temperature and time were 1250$^{\circ}C$∼1400$^{\circ}C$, 2hr., respectively. The structural and microwave dielectric properties were investigated by varying sintering temperature and composition ratio. In the (1-x)MgTiO$_3$-xSrTiO$_3$(x=0.02) ceramics, the cubic SrTiO$_3$and hexagonal MgTiO$_3$phases were coexisted. The dielectric constant was increased and the temperature coefficient of resonant frequency( $\tau_f$) was decreased with addition of SrTiO$_3$. The temperature coefficient of resonant frequency($\tau_f$) was gradually varied from negative value to positive value with increasing the SrTiO$_3$.