• 콘크리트학회논문집
• /
• 제28권5호
• /
• pp.509-517
• /
• 2016

교량의 슬래브에 파손이 발생할 경우 슬래브의 보수보강을 위한 공사로 인해 차량 통행이 제한된다. 모듈러 교량의 경우 이러한 시간적 비용을 줄일 수 있는 방법으로서 많은 연구가 진행되고 있다. 본 연구에서는 연결부에 높은 응력이 발생하는 모듈러 도로 슬래브를 온도하중과 차량하중을 적용하여 구조해석을 실시하였으며 수직연결부 부근에 나선철근을 매입하여 그 성능을 확인하였다. 또한 인양 시의 모듈러 도로 슬래브의 거동 및 취약부분을 확인하기 위하여 인양하중을 적용한 구조해석을 실시하여 유리한 조건의 인양방법을 살펴보았다. 그 결과 온도하중에 의해 수직연결부가 항복하는 것이 확인되었으며, 나선철근을 수직연결부 부분에 매립할 경우 인양 시에 구조물의 손상이 감소하는 것을 확인할 수 있었다. 또한 6개 수직연결부를 이용하여 인양할 시 3개 수직연결부 사용대비 50%의 응력을 감소시킬 수 있는 것으로 확인되었다.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제15권4호
• /
• pp.241-247
• /
• 2015

Purpose : The demand for higher fuel economy vehicles has helped develop fuel-efficient vehicles such as a CVVL called continuous variable valve lift. Existing CVVL has been applying DC type motor to control intake valve, but recently some car parts manufacturers have been developing a BLDC type CVVL motor for improvements of endurance performance. The purpose of this study is to find the potential failure mechanism of the CVVL BLDC moto in early stage of development based on the design properties and design the accelerated life test model. Methods : CVVL BLDC is consist of brushs, coil, magnetic, PCB, bearing and so on. Each component has a latent failure mechanism caused by temperature, humidity, vibration. By analysis result of the failure mechanism, thermal fatigue is the most important factor of a durability of CVVL BLDC motor. So, we designed a new accelerated life test model for guarantee of the CVVL BLDC motor. Results : A crack occurred on via hole in test using the conditions we designed, so we did change the design to avoid this failure. The via hole dimension is changed a little larger, as a result we achieve improvements in reliability of the CVVL BLDC motor. By applying various kinds and extreme level of stresses, we can find the operating limits of products. Conclusion : In thesis, We analyzed the failure mechanism of CVVL BLDC and designed an accelerated life test method to give a guarantee for reliability. Based on the test results, we could improve the reliability of developments by change of design.

• 대한기계학회논문집A
• /
• 제28권9호
• /
• pp.1408-1414
• /
• 2004

The use of flip-chip technology has many advantages over other approaches for high-density electronic packaging. ACF (anisotropic conductive film) is one of the major flip-chip technologies, which has short chip-to-chip interconnection length, high productivity, and miniaturization of package. In this study, thermal fatigue lift of ACF bonding flip-chip package has been predicted. Elastic and thermal properties of ACF were measured by using DMA and TMA. Temperature dependent nonlinear hi-thermal analysis was conducted and the result was compared with Moire interferometer experiment. Calculated displacement field was well matched with experimental result. Thermal fatigue analysis was also conducted. The maximum shear strain occurs at the outmost located bump. Shear stress-strain curve was obtained to calculate fatigue life. Fatigue model for electronic adhesives was used to predict thermal fatigue life of ACF bonding flip-chip packaging. DOE (Design of Experiment) technique was used to find important design factors. The results show that PCB CTE (Coefficient of Thermal Expansion) and elastic modulus of ACF material are important material parameters. And as important design parameters, chip width, bump pitch and bump width were chose. 2$^{nd}$ DOE was conducted to obtain RSM equation far the choose 3 design parameter. The coefficient of determination ($R^2$) for the calculated RSM equation is 0.99934. Optimum design is conducted using the RSM equation. MMFD (Modified Method for feasible Direction) algorithm is used to optimum design. The optimum value for chip width, bump pitch and bump width were 7.87mm, 430$\mu$m, and 78$\mu$m, respectively. Approximately, 1400 cycles have been expected under optimum conditions. Reliability analysis was conducted to find out guideline for control range of design parameter. Sigma value was calculated with changing standard deviation of design variable. To acquire 6 sigma level thermal fatigue reliability, the Std. Deviation of design parameter should be controlled within 3% of average value.

• 한국연소학회지
• /
• 제15권3호
• /
• pp.8-14
• /
• 2010

Fuel processing systems which convert fuel into rich gas (such as stream reforming, partial oxidation, autothermal reforming) need high temperature environment ($600{\sim}1,000^{\circ}$). Generally, anode-off gas or mixture of anode-off gas and LNG is used as input gas of fuel reformer. In order to make efficient and low emission burner system for fuel reformer, it is necessary to elucidate the combustion and emission characteristic of fuel reformer burner. The purpose of this study is to develop a porous premixed flat ceramic burner that can be used for 1~5 kW fuel cell reformer. Ceramic burner experiments using natural gas, hydrogen gas, anode off gas, mixture of natural gas & anode off gas were carried out respectively to investigate the flame characteristics by heating capacity and equivalence ratio. Results show that the stable flat flames can be established for natural gas, hydrogen gas, anode off gas and mixture of natural gas & anode off gas as reformer fuel in the porous ceramic burner. For all of fuels, their burning velocities become smaller as the equivalence ratio goes to the lean mixture ratio, and a lift-off occurs at lean limit. Flame length in hydrogen and anode off gas became longer with increasing the heat capacity. In particular, the blue surface flame is found to be very stable at a very lean equivalence ratio at heat capacity and different fuels. The exhausted NOx and CO measurement shows that the blue surface flame represents the lowest NOx and CO emissions since it remains very stable at a lean equivalence ratio.

• 한국염색가공학회지
• /
• 제11권2호
• /
• pp.19-26
• /
• 1999

Strains degrading and decolorizing acid dyes, Nylosan red E-BL 150%. were isolated from natural system, was named as ARK3. The optimal culture conditions of temperature and pH were $35^\circ{C}$, 7.0, respectively. Growth rate of cells in conditions of aerobic shaking more than standing culture conspicuously increased, and optical density of those to strain ARK3 were found as 1.38 and 0.25 after 42 hrs. Decolorization efficiency in batch culture which used as immobilization media to natural zeolite was 15% after 6 hrs, while suspension culture was 5%, also its of immobilization and suspension culture were 90% and 85% after 48 hrs, respectively. Decolorization efficiency of air-lift bioreactor was more than 90% to a dilution rate of $0.038hr^{-1}$, but that was decreased as 70%, when the dilution rate was $0.05hr^{-1}$. Even though at maximum dilution rate of this study, there was not appeared "wash out" phenomienon of biomass. Decolorization efficiency was 97.7% at a dilution rate of $0.025hr^{-1}$, when influent dye concentration was $100mg/\ell$. But if influent dye concentration increased as $150mg/\ell$, even though MLVSS increased, that of treatment water decreased as 93%. Also, when influent dye concentration increased as $200mg/\ell$ and $300mg/\ell$, decolorization efficiencies of treatment water abruptly decreased as 85% and 63%, respectively. Decolorization efficiency was more than 92% to the limit volumetric loading rate of $3.75mg/\ell\cdot{hr}$hr, without regard to variation of influent dye concentration or hydraulic retention time. if volumetric loading rate was more than $3.80mg/\ell\cdot{hr}$, at same condition, decolorization efficiency was lower decrease of retention time than increase of influent dye concentration.entration.

• 마이크로전자및패키징학회지
• /
• 제13권2호
• /
• pp.21-26
• /
• 2006

NCA의 물성이 미세피치 Chip on glass (COG) 접합부의 신뢰성에 미치는 영향을 연구하였다. Si 위에 Sn을, 유리기판 위에 In을 열증발 방법으로 증착하고 lift-off 방법을 이용하여 $30{\mu}m$ 피치를 가지는 솔더범프를 형성하였으며 열압착 방법으로 $120^{\circ}C$에서 In 범프와 Sn 범프를 접합하였다. 접합할 때 세 종류의 Non conductive adhesive (NCA)를 적용하였다. 신뢰성은 $0^{\circ}C$와 $100^{\circ}C$ 사이로 열충격시험을 2000회까지 실시하여 평가하였다. 4단자 저항측정법을 이용하여 접합부의 저항을 측정하였다. 필러의 양이 증가할수록 열충격시험 후 접합부의 저항이 가장 적게 증가하여 신뢰성이 우수하였다. 필러의 양이 증가할수록 NCA의 열팽창이 작아지기 때문이다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 춘계학술대회 논문집
• /
• pp.7-7
• /
• 2009

Lead telluride (PbTe) is a very promising thermoelectric material due to its narrow band gap (0.31 eV at 300 K), face-centered cubic structure and large average excitonic Bohr radius (46 nm) allowing for strong quantum confinement within a large range of size. In this work, we present the thermoelectric properties of individual single-crystalline PbTe nanowires grown by a vapor transport method. A combination of electron beam lithography and a lift-off process was utilized to fabricate inner micron-scaled Cr (5 nm)/Au (130 nm) electrodes of Rn (resistance of a near electrode), Rf (resistance of a far electrode) and a microheater connecting a PbTe nanowire on the grid of points. A plasma etching system was used to remove an oxide layer from the outer surface of the nanowires before the deposition of inner electrodes. The carrier concentration of the nanowire was estimated to be as high as $3.5{\times}10^{19}\;cm^{-3}$. The Seebeck coefficient of an individual PbTe nanowire with a radius of 68 nm was measured to be $S=-72{\mu}V/K$ at room temperature, which is about three times that of bulk PbTe at the same carrier concentration. Our results suggest that PbTe nanowires can be used for high-efficiency thermoelectric devices.

• 대한기계학회논문집B
• /
• 제37권9호
• /
• pp.837-845
• /
• 2013

공기부양 펌프는 액체 내 공기부양 효과에 의해 양수 조작이 어려운 액체 및 액체 내의 침전물을 손상 없이 토출할 수 있는 장점을 가지고 있다. 이러한 장점을 이용하여 DCFC(Direct Carbon Fuel Cell)에서 고온의 용융된 연료를 혼합 및 순환시키기 위해 공기부양 펌프를 적용할 수 있다. 이를 위한 연구의 일환으로 공기부양 특성을 파악하기 위한 기초 실험을 수행하였다. 본 실험에서는 공기부양 펌프 시스템을 구축하여 저수통 내에 모사 액체로 물을 채우고 관(tube)을 삽입한 후, 관 하단부에 가스유량을 공급하여 상단부의 토출유량을 측정하였다. 설계 인자로서 관직경과 잠수비를 변경하면서 이에 맞는 공기유량을 공급하였고, 정해진 각 조건에서 생성된 관 내부의 기포(bubble) 형상을 디지털 카메라로 촬영, 그 형상을 네 단계로 구분하였다. 펌프의 성능을 이론식을 모델링하여 실험 데이터와 비교하였고, 토출 유량을 측정하여 물이 토출되는 시작점인 가스유량과 전체 유량비와의 상관관계를 분석하였다.

• Tribology and Lubricants
• /
• 제28권6호
• /
• pp.265-271
• /
• 2012

In the preceding Part I study, for improving the unbalance response vibration of a large PRT motor-generator rotor fundamentally by design, a series of design analyses were carried out for bearing improvement by retrofitting from original plain partial journal bearings, applied for operation at a rated speed of 1,800 rpm, to final tilting pad journal bearings. To satisfy evenly key basic lubrication performances such as the minimum lift-off speed and maximum oil-film temperature, a design solution of 5-pad tilting pad journal bearings and maximizing the direct stiffness by about two times has been achieved. In this Part II study, a detailed rotordynamic analysis of the large PRT motor-generator rotor-bearing system will be performed, applying both the original plain partial journal bearings and the retrofitted tilting pad journal bearings, to confirm the effect of rotordynamic vibration improvement after retrofitting. The results show that the rotor unbalance response vibrations with the tilting pad journal bearings are greatly reduced by as much as about one ninth of those with the plain partial journal bearings. In addition, for the tilting pad journal bearings there exist no critical speed up to the rated speed and just one instance of a concerned critical speed around the rated speed, whereas for the plain partial journal bearings there exist one instance of a critical speed up to the rated speed and two instances of concerned critical speeds around the rated speed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.99-99
• /
• 2008

대구경, 고품질 GaN 단결정 기판은 HVPE 방법을 이용하여 제조하였다. 이때 성장 방법은 기판인 $Al_2O_3$ 단결정 기판을 질화처리 하였으며, 이종기판 성장 시 야기되는 격자 불일치와 성장 후 냉각동안에 열팽창 계수의 불일치로 야기되는 휨이나 crack 발생을 제거하기 위하여 step-growth 방법을 사용하였다. 사파이어 위에 성장된 GaN의 기판은 두께가 380um이며, 직경은 3"로 crack 발생은 없었으며, $600^{\circ}C$에서 레이저 분리 방법을 이용하여 사파이어와 분리하였다. 그러나 분리된 기판은 이종기판과의 접촉면에서 고밀도 결함발생으로 인하여 휨이 발생하였으며, 표면을 연마한 후 DCXRD의 FWHM은 107 arcsec, PL을 이용한 결함밀도는 $6.2\times10^6/cm^2$으로 나타났다.