• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.6
• /
• pp.3-14
• /
• 2016

Recently, researches for new waveforms have been carried in order to satisfy KPI for 5G mobile communication system. UFMC and FBMC are well known as ways to reduce OOB power. In this paper, we analyze spectrum of OFDM, UFMC, and FBMC system under nonlinear HPA environment. And then we evaluate and analyze performance of these systems under the same environment. As simulation results, OOB power of OFDM, UFMC, and FBMC increases with HPA nonlinearity increasement. Especially, OOB power of FBMC is the largest increase due to HPA nonlinearity. Also, BER performance of these systems is degraded by increasement of HPA nonlinearity. Therefore, In this paper, we can confirm that a system with low-complexity and high-speed processing is advantageous, because BER performance and OOB power characteristic of these systems are degraded to similar level, when these systems are implemented in real world.

• 전자공학회논문지 IE
• /
• v.44 no.2
• /
• pp.8-13
• /
• 2007

This paper aims to analyze the characteristics of ITO which are caused by variation of plasma condition to fabricate the OLED of high efficiency. We treated $N_2$ gas and $O_2$ gas plasma on the surface of the ITO by changing their RF plasma power into 100 W, 200 W, 400 W and by changing their 9as pressure into 12 mTorr, 120 mTorr. The work function of ITO that plasma treatment was done by using $N_2$ gas had value of $4.88{\sim}5.07\;eV$, and that by using $O_2$ gas, $4.85{\sim}4.97 eV$. The characteristics of the ITO were most efficient in the $N_2$ gas plasma with the RF power of 200W and gas pressure of 120 mTorr. The rms roughness of ITO surface is the value from AFM image. In this case, ITO obtained $25.2\;{\AA}$ and $30.5\;{\AA}$ in the $N_2$ and $O_2$ gas plasma respectively when it had the RF power of 200 W. But ITO that didn't have plasma treatment was $44.5{\AA}$. The variation of ITO transmittance was almost not discovered by the change of $N_2$ gas and $O_2$ gas pressure.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.11
• /
• pp.2121-2130
• /
• 2015

In this paper, we analyze LM-MIMO (load-modulation multiple-input multiple-output) system with single RF chain. And then, we confirm that load modulation technique can support generation of high-order m-PSK modulation and m-QAM modulation in LM-MIMO system. Finally we evaluate performance of LM-MIMO system with load modulation. Conventional MIMO system requires a number of RF chains for expansion of MIMO dimension. A number of RF chains can cause various problems. On the other hand, although LM-MIMO system is expanded, LM-MIMO system requires single RF chain only. Therefore, LM-MIMO system has low-complexity and low power consumption. As results, we can confirm that load modulation of T-model can modulate high-order m-PSK and m-QAM singal. Also, we can confirm that $4{\times}4$ LM-MIMO system using load modulation has a similar performance to conventional $4{\times}4$ MIMO system.

• Journal of Information Technology and Architecture
• /
• v.11 no.1
• /
• pp.53-62
• /
• 2014

The research tries to find appropriate nations and cities of the international supporting centers according to Korean firms' requests. It also tries to find out proper designs of governance structure and strategic and operational control system of the center. Two methods are used to find out Korean firms' requests. One is the expert interviews and the other is the questionnaire survey. The email survey is sent to 120 firms of IT service, package software, telecom facilities and broadcasting equipment industries. Their opinions in addition to interview results are used as a basis of selecting potential regions for new centers and types of their services. According to survey results, southeast asia is the most preferred region and Indonesia, Vietnam, Thailand, Malaysia and Singapore are selected as potential nations for a location of the center in southeast asia. However, the survey result is not fully agreed with the interviewees' opinions. The interviewees tell that there are not much demand in nations with low purchasing power and low IT industry level. That is, Indonesia and Vietnam are not proper places for the centers.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.4
• /
• pp.88-94
• /
• 2007

This paper deals with the performance analysis of 3-dimensional array antenna by DOA estimation and beamforming in GPS receiver for performance improvement by interference elimination. The array antenna in GPS receiver can improve the system performance by estimating DOA of arriving signal direction, making the main beam for desired direction and elimate the jammer signal by nulling while keeping the GPS signal direction by spatial filtering. In this paper, we propose five types of 3-dimensional array antenna and analyze the estimation error via MUSIC algorithm which is used for the estimation of DOA of arrived signal and beamforming performance. In analyzing DOA performance, we measure DOA estimation error, while in analyzing beamformig performance, we measure BER. In beamforming performance analyzing, we use various jammer power and the existence of GPS signal and angle spread. By performing through the computer simulation, Curved (B) 7-element antenna in proposed 3-dimensional array antenna exhibits the superior performance in the DOA estimation, estimation error, BER characteristic and angle spread compared to the rest four array antenna types.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.1
• /
• pp.1-11
• /
• 2000

We propose a predistorter to compensate for nolinear distortion induced by a high power amplifier employed in multi carrier-code division multiple access (MC-CDMA) systems. The proposed scheme rests upon the fixed point iteration (FPI) associated with the contraction mapping theorem. Unlike the predistorter based on the FPI already presented by the authors in other literatures which operates on complex-valued modulation signals, the proposed predistorter in this paper deals with real-valued FPI on modulation signal amplitudes, resulting in less complexity. Simulation results on a BPSK-modulated, 64-subcarrier synchronous MC-CDMA baseband system with a traveling wave tube amplifier in the transmitter, indicate that the proposed predistorter achieves significant improvement in terms of bit error rate and total degradation over those without the predistorter. Moreover, the proposed predistorter outperforms the complex-valued counterpart, in particular, for small output back-off levels.

• Korean Journal of Optics and Photonics
• /
• v.22 no.5
• /
• pp.223-229
• /
• 2011

We present a low jitter frequency up-conversion detector based on quasi-phase matched sum frequency generation in a periodically poled $LiNbO_3$ waveguide for efficient single-photon detection at 1.5 ${\mu}m$ telecommunication wavelengths. The maximum detection efficiency and the noise count rate using the pump power of 300 mW and the pump wavelength of 974 nm are about 7% and 480 kHz, respectively. We also characterize the timing jitter of the frequency up-conversion detector by analyzing the time distribution of the detection outputs for photons generated through a picosecond pump pulsed spontaneous parametric downconversion. The minimum timing jitter was measured to be about 39.1 ps. Coincidence measurement with a narrow time window for pulsed up-conversion photons can eliminate the unwanted noise counts and maximize signal to noise ratio.

• 전자공학회논문지 IE
• /
• v.43 no.4
• /
• pp.1-7
• /
• 2006

In this paper, two types of blue organic light-emitting device were designed. We have analyzed the characteristics of Type I device without a hole blocking layer, and analyzed the characteristics of Type II device using a hole blocking layer of BCP or BAlq materials with 30 ${\AA}$ thickness. We obtained the ITO having the work function value of 5.02 eV using $N_2$ plasma treatment method with the plasma power 200 W. Type I device structure was ITO/2-TNATA/$\alpha$-NPD/DPVBi/$Alq_3$/LiF/Al:Li, and type II device structure was ITO/2-TNATA/$\alpha$-NPD/DPVBi/HBL/$Alq_3$/LiF/Al:Li. We have analyzed the characteristics of Type I and Type II device. The characteristics of the device were most efficiency on occasion of using a hole blocking layer of BAlq material with 30 ${\AA}$ thickness. Current density was 226.75 $mA/cm^2$, luminance was 10310 $cd/m^2$, Current efficiency was 4.55 cd/A, power efficiency was 1.43 lm/W at an applied voltage of 10V. The maximum EL wavelength of the fabricated blue organic light-emitting device was 456nm. The full-width at half-maximum (FWHM) for the EL spectra was 57nm. CIE color coordinates were x=0.1438 and y=0.1580, which was similar to NTSC deep-blue color with CIE color coordinates of x=0.14 and y=0.08.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.11A
• /
• pp.1661-1671
• /
• 2000

본 고에서는 한국통신(Korea Telecom) IMT-2000 시험시스템(이하: Trial system 라고 함) 단말기용 전력증폭단으로 적용하기 위한 다단구동증폭기 및 전력증폭기를 GaAs MMIC로 설계 구현하는 기술을 제시하였다. 설계된 구동증폭기는 3단으로구성하여 RF(Radia Frequency) 송신신호(1955$\pm$70MHz)대역에서 2단 (중간단)의 이득 조정범위가 40 dB이상이 될 수 있도록 능동부품인 MESFET를 Cascade 형으로 구성하고 MESFET의 게이트(gate)에 조정전압을 인가하는 증폭기를 설계하여 GaAs MMIC화 1 침(크기4$\times$5 mm)으로 제작하였다. 아울러, 본 논문에서는 제시한 구동증폭기는 동작주파수 대역폭 범위기 3.5배이고 출력전력은 15dBmm 이며, 출력전력이득이 25~27dB이고 반사계수는 -15~20dB이며 이득평탄도 3dB(동작주파수 대역폭내)로써 Trial system용 단말기의 최종단인 전력증폭단의 출력단 특성을 효과적으로 나타내었다. 그리고, 전력 증폭기는 2개의 입력단에서 출력되는 신호를 분배하는 전력분배기와 병렬구조인 4개의 증폭단에서 출력되는 출력신호를 외부에서 접속하는 전력결합기를 접소하여 구성하였으며 RF(Radio Frequency) 주파수(1955 $\pm$70NHz)에서 대역폭을 4배로 설계하여 광대역인 대역폭을 구현하였고 출력전력은 570mW이며, 출력부가효율(PAE; Power Added Efficency)가 -15$\pm$20dB이고, 이득 평탄도(Gain flatness)는 동작주파수 대역내에서 0.5dB이며 입출력 전압정재파비(Input & Output VSWR)가 13이하인 고출력 전력증포기를 GaAs MMIC화 1칩 (크기; 3$\times$4mm)으로 제작하였다.의 다양성이나 편리성으로 변화하는 것이 국적을 바꾸는 것보다 어려운 시 대가 멀지 않은 미래에 도래할 것이다. 신세기 통신 과 SK 텔레콤에는 현재 1,300만명이 넘 는 고객이 있으며. 이들 고객은 어 이상 음성통화 중심의 이동전화 고객이 아니라 신세기 통신과 SK텔레콤이 함께 구축해 나갈 거대란 무선 네트워크 사회에서 정보화 시대를 살아 갈 회원들이다. '컨텐츠의 시대'가 개막되는 것이며, 신세기통신과 SK텔레콤은 선의의 경쟁 과 협력을 통해 이동인터넷 서비스의 컨텐츠를 개발해 나가게 될 것이다. 3배가 높았다. 효소 활성에 필수적인 물의 양에 따른 DIAION WA30의 라세미화 효율에 관하여 실험한 결과, 물의 양이 증가할수록 그 효율은 감소하였다. DIAION WA30을 라세미화 촉매로 사용하여 아이소옥탄 내에서 라세믹 나프록센 2,2,2-트리플로로에틸 씨오에스터의 효소적 DKR 반응을 수행해 보았다. 그 결과 DIAION WA30을 사용하지 않은 경우에 비해 반응 전환율과 생성물의 광학 순도는 급격히 향상되었다. 전통적 광학분할 반응의 최대 50%라는 전환율의 제한이 본 연구에서 찾은 DIAION WA30을 첨가함으로써 성공적으로 극복되었다. 또한 고체 염기촉매인 DIAION WA30의 사용은 라세미화 촉매의 회수 및 재사용이 가능하게 해준다.해준다.다. TN5 세포주를 0.2 L 규모 (1 L spinner flask)oJl에서 세포간의 응집현상 없이 부유배양에 적응,배양시킨 후 세포성장 시기에 따른 발현을 조사한 결과 1 MOI의 감염조건 하에서는 $0.6\times10^6$cell/mL의 early exponential시기의 세포밀도에서 72시간 배양하였을 대 최대 발현양을 나타내었다. 나타내었다. $\beta$4 integrin의 표현이 침투 능력을 높이는 역할을 하나 이때에는 laminin과 같은 리간드와의 특이

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.2
• /
• pp.123-129
• /
• 2017

This paper proposes a new nonnegative matrix factorization (NMF) based direction-of-arrival (DOA) estimation method for multiple sound sources using a dual microphone array. First of all, sound signals coming from the dual microphone array are segmented into consecutive analysis frames, and a steered-response power phase transform (SRP-PHAT) beamformer is applied to each frame so that stereo signals of each frame are represented in a time-direction domain. The time-direction outputs of SRP-PHAT are stored for a pre-defined number of frames, which is referred to as a time-direction block. Next, In order to estimate DOAs robust to noise, each time-direction block is normalized along the time by using a block subtraction technique. After that, an unsupervised NMF method is applied to the normalized time-direction block in order to cluster the directions of each sound source in a multiple sound source environments. In particular, the activation and basis matrices are used to estimate the number of sound sources and their DOAs, respectively. The DOA estimation performance of the proposed method is evaluated by measuring a mean absolute error (MAE) and the standard deviation of errors between the oracle and estimated DOAs under a three source condition, where the sources are located in [$-35{\circ}$, 5m], [$12{\circ}$, 4m], and [$38{\circ}$, 4.m] from the dual microphone array. It is shown from the experiment that the proposed method could relatively reduce MAE by 56.83%, compared to a conventional SRP-PHAT based DOA estimation method.