• Tribology and Lubricants
• /
• 제32권1호
• /
• pp.9-17
• /
• 2016

Contact between solid surfaces is one of the most important factors that influence dynamic behavior in micro/nanoscale. Although numerous theories and experimental results on contact behavior have been proposed, a thorough investigation for nanomaterials is still not available owing to technical difficulties. Therefore, molecular dynamics simulation was performed to investigate the contact behavior of nanomaterials, and the application of conventional contact theories to nanoscale was assessed in this work. Particularly, the contact characteristics of cylindrical nanowires were examined via simulation and contact theories. For theoretical analysis, various contact models were utilized and work of adhesion, Hamaker constant and elastic modulus those are required for calculation of the models were obtained from both indentation simulation and tensile simulation. The contact area of the cylindrical nanowire was assessed directly through molecular dynamics simulation and compared with the results obtained from the theories. Determination of the contact area of the nanowires was carried out via simulation by counting each atom, which is within the equilibrium length. The results of the simulation and theoretical calculations were compared, and it was estimated that the discrepancy in the results calculated between the simulation and the theories was less than 10 except in the case of the smallest nanowires. As the result, it was revealed that contact models can be effectively utilized to assess the contact area of nanomaterials.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.319-329
• /
• 2016

Globally, many researchers have been trying to improve the fuel economy of a vehicle for satisfying future $CO_2$ regulation and minimizing air pollution problem. For the same background, diesel engine and vehicle system optimization using simulation models have been key technologies for the improvement of vehicle system efficiency. Therefore, in this study, calibration method for the air breathing system of a WGT diesel engine using mean value model has been composed for efficient engine and vehicle optimization simulation researches. And virtual WGT performances have been calculated for a 2 cylinder downsized diesel engine system. From these researches, the calibration method for the boost pressure and EGR rate of a virtual diesel engine related with WGT performances could be composed and some of technical issue related with downsized diesel engine could be investigated.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.103-109
• /
• 2014

This paper represents the s-cam manufacturing process with the high-carbon steel like S45C using laser welding system. Laser welding of the high-carbon steel is generally difficult because of hardening of the weld zone. Also, existing s-cam manufacturing process, electric resistance welding system, have some problems like increase of production and development cost. To solve those problems, we are introduced the laser welding system with the pre-heating system for precision welding of s-cam with separated shaft and cam part. S-cam manufactured with optimum laser welding conditions is verified the performance like tensile strength, torsional strength and fatigue test. Strength and fatigue test results are described.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제7권7호
• /
• pp.1705-1720
• /
• 2013

Human face gender recognition requires fast image processing with high accuracy. Existing face gender recognition methods used traditional local features and machine learning methods have shortcomings of low accuracy or slow speed. In this paper, a new framework for face gender recognition to reach fast face gender recognition is proposed, which is based on Local Ternary Pattern (LTP) and Extreme Learning Machine (ELM). LTP is a generalization of Local Binary Pattern (LBP) that is in the presence of monotonic illumination variations on a face image, and has high discriminative power for texture classification. It is also more discriminate and less sensitive to noise in uniform regions. On the other hand, ELM is a new learning algorithm for generalizing single hidden layer feed forward networks without tuning parameters. The main advantages of ELM are the less stringent optimization constraints, faster operations, easy implementation, and usually improved generalization performance. The experimental results on public databases show that, in comparisons with existing algorithms, the proposed method has higher precision and better generalization performance at extremely fast learning speed.

• 대한임베디드공학회논문지
• /
• 제8권3호
• /
• pp.129-136
• /
• 2013

In this paper, a motion control system based on 2-axis gimbal system is designed and implemented to drive a high speed and precision. The proposed system consists of the RS-422 interface, 2-axis gimbal platform, servo control unit integrated with a high speed DSP chip-set, servo amplifier unit, potentiometer sensor unit, and resolver sensor unit. The servo control unit using the high speed DSP firmware is designed to get a fast response without an overshoot with step input and a RMS error of low probability with ramp input. The servo amplifier unit using a voltage control is designed to resolve the zero-crossing distortion for precise motion. To verify the performance and stability of the implemented system, experiments are performed through a measurement of the time and frequency domain response in a laboratory environment by using a PXI(PCI eXtentions for Instrumentation).

• 전자공학회논문지T
• /
• 제36T권4호
• /
• pp.88-93
• /
• 1999

본 논문에서는 한방의료에서 인체 전신의 상태를 파악하는데 주요한 요소인 맥파를 과학적으로 관찰하고자 스트레인 게이지를 이용하여 맥파를 검출하는 새로운 시스템을 구성하였다. 스트레인 게이지는 센서의 변형에 대해 선형적으로 고유한 저항값이 변화되므로 손목에서 맥의 변화는 스트레인 게이지를 이용하여 맥파의 파형으로 검출할 수 있다. 맥파 검출 시스템의 구성에서 스트레인 게이지로부터 발생된 저항변화값을 검출하기 위해 정밀 브리지회로와 고감도 증폭회로를 설계, 제작하였으며 이 시스템으로 미세한 맥의 변화를 상응하는 전압파형으로 출력시킨다. 구성된 시스템을 이용하여 6인의 맥을 직접 검출하고 시간영역과 주파수 영역에서 맥의 특성을 관찰하므로써 본 연구에서 구성된 맥파 검출 시스템의 과학적인 효용성을 입증하였다.

• Journal of Mechanical Science and Technology
• /
• 제17권1호
• /
• pp.146-156
• /
• 2003

A numerical algorithm is developed to analyze the performance of a Unit-injector (UI) System for a diesel engine. The fundamental theory of the algorithm is based on the continuity equation of fluid dynamics. The loss factors that should be seriously regarded on the continuity equation are the compressibility effect of liquid fuel, the wall friction loss in high-pressure fuel lines of the system, the kinetic energy loss of fuel in the system, and the leakage of fuel out of the control volume. For an evaluation of the developed simulation algorithm, the calculation results are compared with the experimental outputs provided by the Technical Research Center of Doowon Precision Industry Co. (DPICO) ； the maximum pressure in the plunger chamber (P$\_$p/) and total amount of fuel injected into a cylinder per cycle (Q$\_$f/) at each operational condition. The result shows that the average error rate (%) of P$\_$p/ and Q$\_$f/ are 2.90% and 4.87%, respectively, in the specified operational conditions. Hence, it can be concluded that the analytical simulation algorithm developed in this study can be reasonably applied to the performance prediction of newly designed UI system.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1525-1532
• /
• 2010

현대의 측량기술은 위성항법시스템 및 원스톱디지털장비의 등장으로 지구공간상 어느 지점이라도 단일좌표체계의 절대성위치 취득이 가능한 시대로 진보하고 있다. 한편 철도의 속도는 나날이 고속화 되어가고 있어 철도건설시 궤도중심을 포함한 주요시설물 등의 위치를 결정할 때 고도화된 정밀성이 요구된다. 이에 따라 철도건설공사측량에서는 기술지원과 절차가 지침화되어 적용되고 있다. 본 연구에서는 철도건설의 설계와 시공 그리고, 유지관리로 이어지는 과정에서 철도건설측량지침 적용에 따른 측량시 문제점에 대한 대안을 시범지구의 실데이터를 통해 분석 연구 제시하였다.

• 열처리공학회지
• /
• 제5권3호
• /
• pp.171-178
• /
• 1992

The effect of nozzle characterristics on the mist-cooling heat transfer was investigated under the various flow conditions. Two different types of twin fluid nozzle were used, one is a $90^{\circ}$ angle tip nozzle with needle and the other is a $90^{\circ}$ angle tip non-needle nozzle. The cooling rate from the heated surface was measured and obtained the boiling curve as a function of surface temperature. An immersion sampling was employed for the measurement of droplet size of the spray. As a result of this experiment, the liquid sheet type nozzle shows better atomization when the mass ratio Mr>2.0, and collects more liquid droplets on the heated surface that results in better cooling effect. It was found that the maximum heat flux and heat transfer coefficient increased with increase in the volumetric flow rate, whereas the maximum heat flux decreased with increase in spray distance. The cooling effect depends upon the amount of collected droplet and droplet size, but it strongly depends upon the amount of collected droplet.

• 전자공학회논문지CI
• /
• 제45권6호
• /
• pp.1-10
• /
• 2008

보건의료는 u-Healthcare를 통하여 병원중심에서 시민 중심으로 의료 환경변화를 촉진시키고 예방에서 진단, 치료, 사후 관리의 모든 과정을 균형적으로 발전시킬 것으로 전망된다. u-Healthcare 단말이 언제, 어디서나 무자각의 유비쿼터스 단말이 되기 위하여 다음과 같은 기술이 구현되는 것이 필요하다. 이동통신 및 무선 통신망과 연동기능으로 모바일 게이트웨이 구현, Bluetooth 무선 연동기능, 다양한 정보통신기기와의 접목기술, 정밀한 데이터 전송 기술 등이 필요하다 따라서 본 논문은 u-healthcare를 위한 모바일 기반의 시스템 구현에 관한 연구를 수행하였다.