• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.6
• /
• pp.1130-1141
• /
• 2015

Conventionally, a pulse radar is used for middle-sized or large-sized ships to detect other ships or obstacles located at a long distance. However, it is hardly equipped for most of the small-sized ships due to mounting and maintenance costs. Therefore, FMCW(frequency modulated continuous wave) radar is suggested as an alternative for the small-sized ships. Since it operates with low power and has good range resolution for relatively close objects, it is eligible for the small-sized ships. In previously proposed FMCW radar system, it only estimates distance and velocity of a target ship placed in the direction of main beam and is hard to detect several ships simultaneously. Thus, we suggest the method for detecting several ships at the same time by applying MUSIC(multiple signal classification) algorithm to FMCW radar signal received by a phased array antenna. In addition, by combining digital beam forming with the MUSIC algorithm, better angle resolution is achievable.

• Journal of the military operations research society of Korea
• /
• v.33 no.2
• /
• pp.17-29
• /
• 2007

This work describes a basic process of OMS/MP in guided weapons on board ship. The OMS/MP which provided basic data of ROC & RAM analysis must be prepared by user But data acquisition Quantified by specific operational environment of ship and related preparing instructions which are not established are now insufficient of reliable weapon systems acquisition. The OMS/MP is an important area that become measures of Acceptance Test and doctrine considering future battlespace environment From a development of the OMS/MP template that describe systematically and as quantitative of shipped guided weapons, combat developer oriented product development & reliable weapon system acquisition are ta be accomplished. This research developed OMS/MP preparation templete that presented quantified OMS/MP derivation and RAM target value calculation process which provide optimum weapon systems design concept to research developers

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.1
• /
• pp.1-8
• /
• 2017

In this study, a congestion assessment was conducted to verify seasonal differences in congestion for major coastal traffic routes and fairways in major ports with GICOMS Data for 7 days without issuing a special weather report. As a result, a maximum of 11 % and 82 % are shown, with an average of 3.5 % and a 30 % seasonal difference for hourly average congestion and peak time congestion. Therefore, seasonal differences for the target area should be taken into consideration to perform further congestion assessments, particularly for maritime traffic safety assessments, and keen attention should be given to setting up safety measures against congestion.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.5 no.1
• /
• pp.116-131
• /
• 2013

The resistance performance of an icebreaking cargo vessel in pack ice conditions was investigated numerically and experimentally using a recently developed finite element (FE) model and model tests. A comparison between numerical analysis and experimental results with synthetic ice in a standard towing tank was carried out. The comparison extended to results with refrigerated ice to examine the feasibility of using synthetic ice. Two experiments using two different ice materials gave a reasonable agreement. Ship-ice interaction loads are numerically calculated based on the fluid structure interaction (FSI) method using the commercial FE package LS-DYNA. Test results from model testing with synthetic ice at the Pusan National University towing tank, and with refrigerated ice at the National Research Council's (NRC) ice tank, are used to validate and benchmark the numerical simulations. The designed ice-going cargo vessel is used as a target ship for three concentrations (90%, 80%, and 60%) of pack ice conditions. Ice was modeled as a rigid body but the ice density was the same as that in the experiments. The numerical challenge is to evaluate hydrodynamic loads on the ship's hull; this is difficult because LS-DYNA is an explicit FE solver and the FSI value is calculated using a penalty method. Comparisons between numerical and experimental results are shown, and our main conclusions are given.

• Journal of Communications and Networks
• /
• v.18 no.1
• /
• pp.65-74
• /
• 2016

Ship ad-hoc network (SANET) extends the coverage of the maritime communication among ships with the reduced cost. To fulfill the growing demands of real-time services, the SANET requires an efficient clock time synchronization algorithm which has not been carefully investigated under the ad-hoc maritime environment. This is mainly because the conventional algorithms only suggest to decrease the beacon collision probability that diminishes the clock drift among the units. However, the SANET is a very large-scale network in terms of geographic scope, e.g., with 100 km coverage. The key factor to affect the synchronization performance is the signal propagation delay, which has not being carefully considered in the existing algorithms. Therefore, it requires a robust multi-hop synchronization algorithm to support the communication among hundreds of the ships under the maritime environment. The proposed algorithm has to face and overcome several challenges, i.e., physical clock, e.g., coordinated universal time (UTC)/global positioning system (GPS) unavailable due to the atrocious weather, network link stability, and large propagation delay in the SANET. In this paper, we propose a logical clock synchronization algorithm with multi-hop function for the SANET, namely multi-hop clock synchronization for SANET (MCSS). It works in an ad-hoc manner in case of no UTC/GPS being available, and the multi-hop function makes sure the link stability of the network. For the proposed MCSS, the synchronization time reference nodes (STRNs) are efficiently selected by considering the propagation delay, and the beacon collision can be decreased by the combination of adaptive timing synchronization procedure (ATSP) with the proposed STRN selection procedure. Based on the simulation results, we finalize the multi-hop frame structure of the SANET by considering the clock synchronization, where the physical layer parameters are contrived to meet the requirements of target applications.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.6
• /
• pp.391-399
• /
• 2021

In order to investigate force and cavitation characteristics for the flat & twisted rudders in the Large Cavitation Tunnel (LCT), the rudder dynamometer was designed and manufactured. The measuring capacities of lift, drag and moment are ±1000 N, ±2000 N, and ±150 N-m, respectively. The present dynamometer uses the actuator with a harmonic drive to control the rudder angle without backlash. As the target ship is a military ship with twin shaft, each dynamometer was installed above the port & starboard rudders. After the installation of the model ship with all appendages, the model test composed of rudder force measurement and cavitation observation was conducted for the existing flat rudder & the designed twisted rudder. While the flat rudder showed the big difference of lift & moment between port & starboard, the twisted rudder presented a similar trend. The cavitation of the twisted rudder showed better characteristics than that of the flat rudder. Another set of model tests were conducted to investigate rudder performance by the change of the design propeller. There was little difference in rudder performance for the design propellers with slight geometric change. Through the model test, the characteristics of the flat & twisted rudders were grasped. On the basis of the present study, it is thought that the rudder with better performance would be developed.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.3
• /
• pp.175-181
• /
• 2021

This study describes the model tests in ice according to the frictional coefficient of an ice-breaking ship and the change in ice resistance by the analysis method for each component of ice resistances. The target vessel is a 90K DWT ice-breaking tanker capable of operating in ARC7 ice conditions in the Arctic Ocean, and twin POD propellers are fitted. The hull was specially painted with four different frictional coefficients on the same ship model. The total ice resistance can be separated by ice breaking, ice buoyancy, ice clearing resistances through the tests in level ice, pre-sawn ice and creep test in pre-sawn ice under sea ice thickness of 1.2 m and 1.7 m. Ice resistance was analyzed by correcting the thickness and bending strength of model ice by the ITTC correction method. As the frictional coefficient between the hull and ice increases, ice buoyancy and clearing resistances increase significantly. When the surface of the hull is rough, it is considered that the broken ice pieces do not slip easily to the side, resulting in an increase in ice buoyancy resistance. Also, the frictional coefficient was found to have a great influence on the ice clearing resistance as the ice thickness became thicker.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.1
• /
• pp.31-37
• /
• 2023

In the present study, a method of performing cavitation erosion test directly on the anodized surface of the rudder model is proposed, not applying ink or paint on its surface. An image processing technique is newly developed to quantitatively evaluate the erosion damages on the rudder model surface after erosion test. The preprocessing saturation image, image smoothing, adaptive hysteresis thresholding and eroded area detection algorithms are in the image processing program. The rudder cavitation erosion tests are conducted in the rudder deflection angle range of 0° to -4°, which is used to maintain a straight course at the highest speed of the targeted navy ship. In the case of the conventional flat-type full-spade rudder currently being used in the target ship, surface erosion can occur on the model rudder surface in the above rudder deflection angle range. The bubble type of cavitation occurs on rudder surface, which is estimated to be the main reason of erosion damage on the rudder surface.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.3
• /
• pp.248-254
• /
• 2015

There has been no previous study on technology development of large capacity drainage pump for rescue sinking ship in the country. The agricultural drainage pump was widely used for rescue sinking ship but this pump has several problems such as efficiency, low displacement and malfunction in winter. Therefore, this paper proposes to solve the problems for swiftly rescue sinking ship and develops the drainage pump system that has $20m^3/min$ mass flow rate specification at suction head 8 m. The centrifugal pump type the most commonly used in the field of naval architecture and ocean engineering was selected and designed based on the requirement specification. The blade design of impeller was derived from the Stepanoff coefficient and requirement specification and used computational fluid dynamics to review the target mass flow rate according to the impeller RPM at design operating conditions. We also performed structure analysis of the impeller to find structurally vulnerable points for the pump in service and completed the theoretical design of drainage pump system.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.6
• /
• pp.535-541
• /
• 2008

As the concurrent engineering concept has emerged along with the support of optimization techniques, lots of endeavors have been made to apply optimization techniques to actual design problems for a holistic decision. Even if the range of design problems which the optimization is applicable to has been extended, most of ship designs still remain in an iterative approach due to the difficulties of seamless integration of all related design activities. In this approach, an entire design problem is divided into many sub-problems and carried out by many different disciplines through complicated internal interactions. This paper focuses on preliminary ship design process. This paper proposes a process centric integrated framework as the first step to establish a workflow based design process management system. The framework consists of two parts; a schedule management part to support a manager to monitor current progress status and adjust current schedule, and a process management part to assist a design to effectively perform a series of design activities by following a predefined procedure. Overall system are decomposed into modules according to the target to be managed in each module. Appropriate interactions between the decomposed modules are designed to achieve a consistency of the entire system. Design process model is also designed on a thorough analysis of actual ship design practice. The proposed framework will be embodied using a commercial workflow package.