• Journal of Aerospace System Engineering
• /
• v.11 no.6
• /
• pp.64-67
• /
• 2017

This work dealt with structural safety analysis about sandwich composite structure of automotive floor board. In this work, structural design and analysis of sandwich composite structure for automobile floor board were performed. Firstly, structural design requirement of automobile floor board was investigated. After structural design, the structural analysis of the automobile floor board were performed by the finite element analysis method. It was performed that the stress and displacement analysis at the applied load condition. After structural test of target structure, structural test results were compared with analysis results. Through the structural analysis, it was confirmed that the designed floor board structure is safety.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1684-1688
• /
• 2003

In this paper, position and speed control algorithm of LSM (Linear Stepping Motor) using general-purpose PCI I/O board is discussed. The main purpose of this paper is to show that LSM controller can be established on the non real time operating system such as Microsoft Win2000 under the assumption that thread priority strategy is well designed. We can guarantee sampling interval less than 5msec based on the Pentium III microprocessor. Therefore this kind of LSM controller development environment makes shorten the prior research period needed to verify the validness of the proposed control strategy. We also introduce the tool of the real-time windows target system of matlab, which also makes shorten the prior research period. The main focus of this paper is on developing general purpose NT device driver which can drive the general purpose PCI board and applying it for implementing the hardware interface for 2- axis linear stepping motor control. From the experimental results show that the developed LSM controller guarantee 2 micrometer resolution in position control with 10cm/sec moving speed

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.56-63
• /
• 1996

This study was to manufacture thinned wood of Larix leptolepis Gordon into Oriented Strand Board(OSB) with Urea-Formaldehyde Resin. The OSB was made of four kinds of strand in slenderness ratio 150 ; thickness $0.3{\pm}0.05mm$, $0.4{\pm}0.05mm$, $0.5{\pm}0.05mm$ and $0.6{\pm}0.05mm$, respectively length 45mm, 60mm, 75mm and 90mm. Target densities were 0.65gr/$cm^3$, 0.75gr/$cm^3$ and 0.85gr/$cm^3$. The stepwise 9 minutes-multi-pressing schedule in the maximum pressure 40kgf/$cm^2$, the minimum pressure 10kgf/$cm^2$ was applied for $400mm{\times}390mm{\times}12mm$ board at the temperature of $150^{\circ}C$ in a hot press. In MOR The OSB of thin strand thickness $0.3{\pm}0.05mm$(length 45mm) and density 0.85gr/$cm^3$ was the highest. The strand thickness had more effect on MOR than the strand length. In strand thickness $0.4{\pm}0.05mm$(length 60mm) and density 0.85gr/$cm^3$ was the highest MOE. The strand thickness and length had adverse effects on MOE each other. At internal bonding. The OSB of strand thickness $0.3{\pm}0.05mm$(length 45mm) and board density 0.75gr/$cm^3$ showed the highest value. OSB had higher IB value with thinner strand thickness. The thinner strand thickness showed the lower thickness swelling in turn $0.3{\pm}0.05mm$(length 45mm), $0.4{\pm}0.05mm$(length 60mm), $0.5{\pm}0.05mm$(length 75mm). $0.6{\pm}0.05mm$(length 90mm). Target densities 0.75gr/$cm^3$ 0.65gr/$cm^3$, 0.85gr/$cm^3$ showed in turn lower value. Finally, The OSB made of thinned wood of Larix leptolepis Gordon showed good results in laboratory experiment.

• Journal of Positioning, Navigation, and Timing
• /
• v.7 no.2
• /
• pp.105-112
• /
• 2018

This paper manufactured an active GPS antenna for ground vehicles and presented a method to verify the performances of the antenna and component technology of the low noise amplifier (LNA) board manufacturing. The manufactured GPS antenna is an active antenna where microstrip patch and LNA board were combined. The main performances were standing wave ratio, antenna gain, and axial ratio, and all satisfied the target specifications. The proposed component technology can be utilized as a basis data in which the performance of LNA board can be compensated in the mass production process inspection, and employed as a method to verify whether antennas are properly working in environmental tests.

• The Journal of Information Technology
• /
• v.8 no.4
• /
• pp.91-102
• /
• 2005

In this paper, development of embedded system based on Windows CE 5.0 which released recently is studied. Embedded softwares for the target board using S3C2410A SOC based on ARM920T core are composed of (1) BSP(Board Support Package) contains an OAL(OEM Adaptation Layer) which includes a boot loader for initializing and customizing target hardware, device drivers, and a corresponding set of configuration files (2) Windows CE 5.0 kernel (3) SDK and MP3 test application. Particularly, PB(Platform Builder) provides the efficient functions to build, test and debug the BSP and CE kernel. It is looked forward to being widely spread that Windows CE 5.0 will be utilized at smart devices such as PMP, CNS and DMB phone which inevitably require a display device.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.3
• /
• pp.241-248
• /
• 1996

The relationship between width of line target and distance at the limit of discrimination was examined by means of the behavioral method, for filefish Stephanolepis cirrhifer from 11 to 15cm body length. Target distance was distance from beginning of partition board to target plate, and was varied from 50cm to 200cm. The target plate was made of white acrylic resin with a vertical black line in the center. The width of line target was varied from 0.2mm to 8.0mm. Fish were trained to respond to a line target and the width of line target reduced until the minimum width required to elicit a response was established. Rate of success was expressed as the percentage of target choices in 90 trials. The line acuity of filefish was found to be 0.58 at a target distance of 50cm. The rate of success decreased slowly as line target width decreased from 8.0mm to 1.5mm, and decreased suddenly for target widths less than about 1.5mm. The width of the line target D(mm) at the limit of discrimination was shown to be an exponential function of the target distance L(cm) as follows : D=exp(9.947$\times$$10^-3$.L+0.146)

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.1
• /
• pp.38-43
• /
• 2012

Sound absorption capability and mechanical properties such as MOE and MOR in bending of miscanthus particle based board were estimated by the two microphone transfer function method and three point bending method, respectively. The results are summarized as follows: The sound absorption coefficients of miscanthus particle based board was higher than those of commercial gypsum board which is well used as sound absorbing barrier. The MOR and MOE of miscanthus particle based board increased with increasing of board density. The sound absorption coefficients of miscanthus particle based board were 50~80% in the frequency range of about 1~2.5 Khz. In entire frequency range, those value increased with target board density decreasing.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.5
• /
• pp.15-22
• /
• 2003

This study was carried out to investigate the properties of sawdust board impregnated with phenol resin according to the density and resin content of board. The sawdust board were manufactured to target densities of 0.4, 0.5, 0.6, 0.7 g/cm³ and resin content of 5, 10, 15, 20% made from Pinus densiflora S. et Z., Larix. kaemferi C. and Pinus koraiensis S. et Z. The impregnation process were executed in two ways, the application of vacuum pressure then followed by atmospheric pressure, and the application of vacuum pressure with ultrasonic vibration then followed by atmospheric pressure. The density of impregnated sawdust board increased as density and resin content of sawdust board increased, but impregnation rate decreased. The density, impregnation rate, bending strength and brinell hardness of sawdust board in impregnated vacuum pressure with ultrasonic vibration then nonpressure were higher than those of vacuum pressure then nonpressure. In this results, the impregnation rate is increased in vacuum pressure with ultrasonic vibration then nonpressure, it has affected the properties of sawdust board impregnated with phenol resin.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.2
• /
• pp.196-205
• /
• 2020

The purpose of this study was to investigate a method for improving the physical and mechanical properties of laminated board made from oil palm trunk (OPT). The effects of pretreating the lamina with heat-pressure and altering the lamina composition of the laminated board were investigated. The outer third of OPT in cross-section had high-density wood, while the underlying third had low to medium density. The hot press was applied to pretreat the lamina that had low to medium density. The lamina were 1.5 cm in thickness, 5 cm in width, and 65 cm in length. The hot press was applied at 2.94 MPa or 4.41 MPa at 150 ℃ for 60 minutes, and the target thickness of the lamina was 1 cm. The three layers of the laminated board samples were bonded with isocyanate adhesive at a glue spread of 300 g/㎡ and cold pressed at 0.98 MPa for 3 h. The laminated board samples were tested according to Japanese Agricultural Standard (JAS) 234-2003. The results showed that the densification of the inner lamina did not significantly affect the physical-mechanical properties of the laminated board produced. However, the laminated board made with high-density laminas for the outer layers fulfilled the JAS 234-2003 standard for the modulus of elasticity and the modulus of rupture.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.2
• /
• pp.57-65
• /
• 1993

The aim of this research was to manufacture sludge-particle board using paper sludge with wood particle and to investigate physical and mechanical properties of various sludge-particle boards, fabricated with ratios of sludge to particle of 10 to 90, 20 to 80, 30 to 70, 40 to 60 and 50 to 50(oven dry weight based). Sludge-particle boards were manufactured by urea-formaldehyde resin, 0.8 target specific gravity, and 10mm thickness. It was possible to manufacture sludge-particle board as the same processing in the present particleboard manufacturing system. This sludge-particle board have different properties as composition ratios of sludge and particle. And sludge-particle board made from 10 percent to 20 percent of sludge mixing ratio have similar mechanical properties compared with control particleboard. Especially, the sludge-particle board made from 10 percent to 40 percent mixing ratios of sludge have superior to control particleboard in internal bond, screw withdrawal holding strength and modulus of elasticity. In the case of dimensional stability, water absorption was increased and thickness swelling was decreased as increased with sludge mixing proportion. The sludge-particle board made of different mixing ratios of our laboratory design was able to concluded that there is possibility of partial substitution of wood particle materials.