• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3195-3201
• /
• 1994

In order to analytically predict tapping torque and thrust force in high speed tapping, a cutting model for main cutting edge with a uniformly restricted tool-chip contact area were developed. From this model equations are derived for the prediction of tapping torque given the cutting conditions, tap geometry, and an empirical factor which is related to the workmaterial. Computed values of torque is shown to compare favorably with those obtained from tapping tests on 16MnCr5. The applied torque about the cutting edge of teeth at lead chamfer is estimated respectively and it is shown that observed value is gradually decreased with following teeth.

• 한국정밀공학회지
• /
• 제18권11호
• /
• pp.67-73
• /
• 2001

This paper aims at developing a torque model for the high-speed tapping with small-diameter taps. As recent industries such as automobile and information technology grows, taps smaller than 5mm in diameter are needed much more. In that occasion, the friction force between a tap surface and a workpiece plays much more important role in the tapping torque than in he larger tapping. Tapping mechanism was analysed based on the tap geometry. It has two steps : one is a forward cutting composed of the chamfered threading and full threading and the other is the backward cutting. The torque by the cutting force in the chamfered threading is calculated using the cutting area and the specific cutting force while the torque by the friction force, which is rather dominant than the cutting force both in the full threading and in the backward cutting, is calculated using the normal force on the threads and the friction coefficient. The experiment has shown that the results by the proposed torque model fit quite well with the acutal measurements within the error of 10%.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.538-541
• /
• 2005

In tapping mode atomic force microscopy(TM-AFM). the vibro-contact response of a resonating tip is used to measure the nanoscale topology and other properties of a sample surface. However, the nonlinear tip-surface interact ions can affect the tip response and destabilize the tapping mode control. Especially it is difficult to obtain a good scanned image of high adhesion surfaces such as polymers and biomoleculars using conventional tapping mode control. In this study, theoretical and experimental investigations are made on the nonlinear dynamics and control of TM-AFM. To analyze the complex dynamics and control of the tapping tip, the classical contact models are adopted due to the surface adhesion. Also we report the surface adhesion is an additional important parameter to determine the control stability of TM-AFM. In addition, we prove that it is more adequate to use Johnson-Kendall-Roberts (JKR) contact model to obtain a reasonable tapping response in AFM for the soft and high adhesion samples.

• 한국항공우주학회지
• /
• 제37권11호
• /
• pp.1089-1095
• /
• 2009

태핑 테스트 시 방사되는 음압을 Rayleigh 적분식을 이용하여 해석하였다. 구조물에 의해 방사되는 음은 구조물의 거동과 직접적으로 연관되므로 충격응답해석이 수행되어야 한다. 본 논문에서는 층간분리가 존재하는 적층판의 해석을 위하여 층간분리 모델을 사용하였으며, 해머 형상의 충격체를 모사할 수 있는 효과적인 스프링-질량모델을 제시하였다. 예측된 음압이력과 시험결과와 비교하였으며, 음압이력과 충격하중이력에 손상이 주는 영향을 검토하였다. 방사되는 음압과 충격하중이력은 적층판에 존재하는 손상에 영향을 주는 것을 보였다. 결과적으로 제안된 음을 이용한 태핑실험은 복합재에 존재하는 손상을 검출하는데 신뢰성 있는 방법임을 알 수 있었다.

• 구강회복응용과학지
• /
• 제25권4호
• /
• pp.391-401
• /
• 2009

임플란트의 성공은 식립 후의 초기 안정성 (Initial stability)의 결과가 중요한 영향을 준다. 이 연구의 목적은 연질 골에서 두 종류의 테이퍼 형태 임플란트가 임플란트의 디자인과 self-tapping blade의 유무에 따라서 초기 안정성에 주는 영향을 알아보는 것이다. Self-tapping blade를 가지고 있는 것과 가지고 있지 않은 두 종류의 테이퍼 형태 임플란트가 사용되었다. Solid Rigid Polyurethane Form으로 연질 골 상태인 D4 골 모형을 재현하였다. 임플란트 고정체를 식립하면서 초기 안정성 값을 기록하고, 식립 직후 implant stability quotient (ISQ)을 측정하여 Resonance frequency Analysis (RFA)를 평가하였다. 마지막으로 임플란트가 식립된 모형골을 만능 시험기에 부착하여 장축 방향으로의 pull-out force를 측정하였다. 초기 안정성 값과 최대 pull-out torque 값은 non self-tapping implants가 self-tapping group에 비하여 통계학적으로 유의하게 큰 평균값을 나타냈다 (P = 0.008). 공진 주파수 분석 결과인 ISQ 값은 거의 비슷한 평균값을 보였으면 통계학적으로 차이가 없었다. 각 임플란트 시스템에서 식립 토크와 pull-out 최대 토크 그리고 공진 주파수 간에는 상관관계를 나타내지 않았다. Non self-tapping 임플란트의 높은 식립 토크는 임상적으로 우수한 초기 안정성을 의미한다. 결론적으로 연질 골에서 self-tapping blade가 없는 임플란트가 있는 것 보다 더 우수한 초기 안정성을 보였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.606-611
• /
• 2007

Proper orthogonal decomposition (POD) is a method for extracting bases for modal decomposition from the ensemble of dynamic signals. Using the POD method, we analyzed the proper orthogonal modes (POMs) of AFM microcantilevers in dynamic mode operations such as Tapping Mode. The POMs and POVs (proper orthogonal values) were computed through MATLAB simulation for the 5-mode model of the microcantilever. We found that the POV portion of the higher POMs of the tapping microcanilever slightly increased in comparison with no tapping. This implies that the modal energy in the fundamental mode can be transferred to the higher modes during tapping.

• 대한기계학회논문집A
• /
• 제30권2호
• /
• pp.135-140
• /
• 2006

In tapping mode atomic force microscopy (TM-AFM), the vibro-contact response of a resonating tip is used to measure the nanoscale topology and other properties of a sample surface. However, the nonlinear tipsurface interactions can affect the tip response and destabilize the tapping mode control. Especially it is difficult to obtain a good scanned image of high adhesion surfaces such as polymers and biomolecules using conventional tapping mode control. In this study, theoretical and experimental investigations are made on the nonlinear dynamics and control of TM-AFM. Also we report the surface adhesion is an additional important parameter to determine the control stability of TM-AFM. In addition, we proved that it was adequate to use Johnson-Kendall-Roberts (JKR) contact model to obtain a reasonable tapping response in AFM for the soft and high adhesion samples.

• Journal of Forest and Environmental Science
• /
• 제27권3호
• /
• pp.135-141
• /
• 2011

The present study was carried out from September 2007 to February 2008 in Umfakarin natural forest reserve, South Kordofan, Sudan. The objective was to analyze the effect of different management strategies on yield of gum talha from Acacia seyal. A total of 493 single target trees were selected, based on their diameters, and assigned to tapping treatments in three different stand densities (making a total of nine treatments per stand density). The treatments are as follows: tapping date with three levels (first of October, 15 October and first of November) and two levels of local tapping tools (sonki, and makmak). Untapped trees were used as control. The first picking of gum was started fifteen days after tapping while the subsequent pickings were done in intervals of fifteen days. Yield per tree throughout the season was obtained by summing up the gum yield from all pickings. Yield throughout the season (from first to the last picking) were analyzed. General linear model (GLM) was used to test the effect of different tapping treatments on the yield of gum talha. Post hoc test after analysis of variance (ANOVA) based on Scheffe test was performed to examine the differences in gum yield as a result of different management strategies. The results showed that tapping has a significant influence on gum yield. Analysis of pick-to-pick yield indicated that only three treatments in dense stand density showed a decreasing pattern while the rest of treatments either have constant or unclear patterns. The results of the present study were based on a single season data and that may underscore the real effect of Acacia seyal stands' management strategies on gum talha yield. Conducting gum yield experiments in permanent trial plots are highly recommended in order to analyze gum yield of seasonal time series.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1560-1565
• /
• 2003

Tapping mode atomic force microscopy (TM-AFM) utilizes the dynamic response of a resonating probe tip as it approaches and retracts from a sample to measure the topography and material properties of a nanostructure. We present recent results based on nonlinear dynamical systems theory, computational continuation techniques and detailed experiments that yield new perspectives and insight into AFM. A dynamic model including van der Waals and Derjaguin-Muller-Toporov (DMT) contact forces demonstrates that periodic solutions can be represented with respect to the approach distance and excitation frequency. Turning points on the surface lead to hysteretic amplitude jumps as the tip nears/retracts from the sample. Experiments are performed using a tapping mode tip on a graphite sample to verify the predictions.

• Journal of the Optical Society of Korea
• /
• 제16권1호
• /
• pp.57-62
• /
• 2012

Using continuous wave near-infrared spectroscopy, we measured time-resolved concentration changes of oxy-hemoglobin and deoxy-hemoglobin from the primary motor cortex following finger tapping tasks. These data were processed using partial least squares-discriminant analysis (PLS-DA) to develop a prediction model for a brain-computer interface. The tasks were composed of a series of finger tapping for 15 sec and relaxation for 45 sec. The location of the motor cortex was confirmed by the anti-phasic behavior of the oxy- and deoxy-hemoglobin changes. The results were compared with those obtained using the hidden Markov model (HMM) which has been known to produce the best prediction model. Our data imply that PLS-DA makes better judgments in determining the onset of the events than HMM.