• Journal of Korean Society for Quality Management
• /
• v.41 no.1
• /
• pp.119-134
• /
• 2013

Purpose: The purpose of this paper is to show whether the results are changed with respect to the variance of the data, by analysis of data obtained from the Taguchi experimental techniques and general experiment. Because which cannot be prove by mathematical Formula, through experimental examples will show. Methods: Taguchi experiments were carried out with paper Helicopter experiment. Experimental Data are obtained by special designed Drop Test Equipment. While Experimental value arbitrarily changed, we looked at how Significant control Factor of Taguchi Methods and Factor experiments are changed. This process cannot be expressed as a Mathematical formula, but showed as a numerical example. Results: Saw significant changes in the factors when data is outside a certain range of the experimental data. By Test of Equivalence Variance, Experiment data is verified reliability. To find the Control Factor, Taguchi Method is better than the general experiment. Conclusion: We know that a Significant Factor is changed with the range of Variance of Experiment Data. The value of this paper is verified change process with Numerical Data obtained Experiment.

• Journal of the military operations research society of Korea
• /
• v.27 no.1
• /
• pp.101-113
• /
• 2001

Taguchi and VTA(variation Transmission Analysis) methods have been widely used recently as new methods for product design. In this study, Taguchi method using analysis of variance and VTA method using regression analysis are reviewed and compared with each other in terms of parameter design and tolerance design. In analysis of variance, variation of quality characteristics arises from noise factors, therefore the optimal levels of design factors are selected to minimize the effect of noise factors. n regression analysis, variation of quality characteristics arises from variation of each own design factors. As a method to reduce variation of these quality characteristics, sensitivity analysis was performed for each design factors. An example of calculating tolerance interval for the given defect rate in PPM is also introduced. Especially, the new method is suggested to increase the estimation accuracy of variation of quality characteristics through regression analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.157-162
• /
• 2003

This Paper presents a robust design of an Electrorheological(ER) damper using Taguchi method. Taguchi method is a robust design method that determines control parameters in the presence of noise effect. Electrode length, electrode gap, base oil viscosity and the weight ratio of ER particles are chosen for the control parameters and the temperature is considered to be a noise factor. The sensitivity of each factor with signal-to-noise(S/N) ratio and analysis of variance are investigated. The analysis results show that the electrode length and base oil viscosity of the ER fluid mostly affect the damping force in the absence of electric field. On the other hand, when the voltage is applied to the ER damper, the electrode length and the weight ratio of ER fluid exhibit significant effect. Based on the Taguchi method, an optimal configuration was designed and the robustness of the designed ER damper was validated by comparing the analysis and experimental results.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.66-77
• /
• 1997

In the present work, Taguchi method for electron beam welding(EBW) process in AISI 4130 steel plate has been adopted for investigating the contribution of effect of welding variables. $A L_8(2^7)$ orthogonal array is adopted to obtain the effect of adjustment parameters. The adjustment parameters consist of accelerating voltage, beam current, travel speed and focus currrent. And the quality features selected for the EBW process are bead width of weldment, reinforcement, penetration depth, undercut and area of weld metal. Variance analysis is performed in order to check the effect of adjustment parameters on EBW. The mechanical properties of electron beam welded joints for each heat treatment conditions are investigated in comparison with those of base metal, especially from the view point of tensile and impact properties.

• Journal of Power System Engineering
• /
• v.17 no.6
• /
• pp.108-114
• /
• 2013

This paper describes process optimization for thermal-sprayed Co-based self-flux alloy coating by Taguchi method. Co-based self-flux alloy coatings were fabricated according to $L_9(3^4)$ orthogonal array using flame spray process. Hardness test and wear test were performed, the results were analyzed by analysis of variance(ANOVA) considering a multi response signal to noise ratio(MRSN). From the results of ANOVA, the optimal combination of the flame spray parameters on Co-based self-flux alloy coating could be predicted. The calculated hardness and wear rate of the coatings by ANOVA were found to be close to that of confirmation experimental result.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.638-642
• /
• 2003

This paper presents a parameter design of an Electrorheological(ER) panel for noise reduction using Taguchi method. Taguchi method is a robust design method that determines control parameters in the presence of noise effect. Host structure thickness, spacer thickness, base oil viscosity and the weight ratio of ER particles are chosen for the control factors. A test setup in an SAE J1400 facility is used to analyze the sound transmission loss. The sensitivity of each factor with signal-to-noise(S/N) ratio and analysis of variance are investigated. The analysis results show that the weight ratio of ER particle and base oil viscosity of the ER fluid mostly affects the noise reduction in the presence of electric field. Based on the Taguchi method, an optimal configuration was designed and comparison is made with experimental result fer the verification.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.221-222
• /
• 2010

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.534-538
• /
• 2004

On this study, we improved diaphgram for micro speaker performance using Taguchi method in discrete design space. The design of diaphgram has an effect on performance of micro speaker such as, thickness of diaphgram, shape of diaphgram, etc. Therefore this study carried to decide shape of diaphgram and thickness of diaphgram for minimizing 2nd natural frequency of diaphgram using Taguchi method. we showed improved design factors that minimized 2nd natural frequency of diaphgram. Also, 2nd natural frequency of diaphgram for micro speaker is reduced up to 37 percent maintaining twist mode shape. From the results of ANOVA, 2nd natural frequency of diaphgram for micro speaker have an effect on position of the outer curved shape and thickness of diaphgram.

• Journal of Power System Engineering
• /
• v.16 no.2
• /
• pp.54-59
• /
• 2012

In the present study, process optimization for thermal-sprayed Ni-based alloy coating has been performed using Taguchi method and analysis of variance(ANOVA). Ni-based alloy coatings were fabricated by flame spray process on steel substrate, and the hardness test and wear test were performed. Experiments were designed as per Taguchi's L9 orthogonal array and tests were conducted with different Oxygen gas flow, Acetylene gas flow, Powder feed rate and Spray distance. Multi response signal to noise ratio (MRSN) was calculated for the response variables and the optimum combination level of factors was obtained simultaneously using Taguchi's parametric design.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.3
• /
• pp.97-103
• /
• 2001

This paper has focused on the Optimization of the cutting parameters for urning operation based on the Taguchi method. Four cutting parameters. nemely, cutting speed, feed depth of cut and nose radius are optimized with consideration of the surface roughness. The design and analysis of experiments are conducted to study the performance characteristic. The effects of these parameters on the surface roughness have been investigated using signal-to-noise(S/N) ratio and analy-sis of variance(ANOVA). The experiments have been performed using coated tungsten carbide inserts without any cutting fluid. Experimental results illustrate the effectiveness of this approach.