선택적 촉매 환원(SCR)은 질소산화물 배출을 줄이는 가장 효과적인 방법이지만, V2O5-WO3/TiO2 촉매가 좁은 작동온도 (300~400℃) 범위를 가지기 때문에, V2O5-WO3/TiO2 촉매의 작동 온도범위가 200~450℃인 새로운 촉매를 개발하였다. SCR 과정에서 생성되는 촉매 독인 황산암모늄은 350℃ 이상으로 가열함으로써 제거할 수 있다. 촉매 활성 부위의 수를 증가시키고 활성 물질의 분산을 촉진하기 위해 TiO2 지지체에 티타늄 이소프로폭사이드(TTIP) 처리를 여러 TTIP/TiO2 질량비로 진행하였다. 그 중 5 wt% TTIP 부하에서 높은 W 분산성으로 인해 열 안정성이 증가하였고 V5+가 형성되어 최적의 성능을 보였다. 5 wt% TTIP 부하로 처리된 촉매를 One-step co-precipitation으로 제조하였을 때 기존의 방법보다 더 나은 V-OH와 W-OH 분산 및 상호작용 향상이 나타나 더 낮은 온도에서 높은 촉매 활성으로 인해 향상된 성능을 보였다. 이를 향후 TTIP를 이용하여 TiO2촉매의 표면을 개선하려는 연구자에게 이해하기 쉽게 설명하고자 하였다.
$TiO_2$ films were deposited from oxygen/titanium tetraisopropoxide (TTIP) plasmas at low temperature by Helicon-PECVD at floating potential ($V_f$) or substrate self-bias of -50 V. The influence of titanium precursor partial pressure on the morphology, nanostructure and optical properties was investigated. Low titanium partial pressure ([TTIP] < 0.013 Pa) was applied by controlling the TTIP flow rate which is introduced by its own vapor pressure, whereas higher titanium partial pressure was formed through increasing the flow rate by using a carrier gas (CG). Then the precursor partial pressures [TTIP+CG] = 0:027 Pa and 0.093 Pa were obtained. At $V_f$, all the films exhibit a columnar structure, but the degree of inhomogeneity is decreased with the precursor partial pressure. Phase transformation from anatase ([TTIP] < 0.013 Pa) to amorphous ([TTIP+CG] = 0:093 Pa) has been evidenced since the $O^+_2$ ion to neutral flux ratio in the plasma was decreased and more carbon contained in the film. However, in the case of -50 V, the related growth rate for different precursor partial pressures is slightly (~15%) decreased. The columnar morphology at [TTIP] < 0.013 Pa has been changed into a granular structure, but still homogeneous columns are observed for [TTIP+CG] = 0:027 Pa and 0.093 Pa. Rutile phase has been generated at [TTIP] < 0:013 Pa. Ellipsometry measurements were performed on the films deposited at -50 V; results show that the precursor addition from low to high levels leads to a decrease in refractive index.
$TiO_2$의 물리적 특성이 메틸렌 블루 광분해 특성에 미치는 영향을 연구하기 위해, $HNO_3$/TTIP가 0.1, 0.5, 1.0과 1.5인 몰비에서 아나타제와 아나타제/루틸 $TiO_2$ 시료들이 제조되었다. XRD, SEM, TEM, BET, FT-IR과 UV-vis 분광기를 사용하여 시료들의 물리적 특성을 측정하였다. 아나타제 상이 $HNO_3$/TTIP가 0.1인 시료에서 관찰되었고, 아나타제/루틸 상은 $HNO_3$/TTIP가 0.5~1.5인 시료들에서 관찰되었다. $HNO_3$/TTIP 몰 비를 증가시킴에 따라 루틸 결정상, $TiO_2$ 나노입자 사이의 메조 세공 크기와 $TiO_2$의 표면 OH 작용기는 점차 증가하였고, UV 조사 전 메틸렌 블루 잔류 농도는 78.0에서 53.3%으로 감소하였다. UV 조사 후 $HNO_3$/TTIP가 0.1, 0.5, 1.0과 1.5에서 제조된 시료들의 잔류 메틸렌 블루 농도는 각각 20, 14, 11과 23%이었고, $HNO_3$/TTIP가 1.0에서 제조된 시료가 가장 우수한 광촉매능을 나타내었다.
원자전달 라디칼 중합을 이용하여 poly(styrene sulfonic acid) 47 wt%를 가진 poly(vinylidene fluoride-co-chlorotrifluoroethylene)-g-poly(styrene sulfonic acid) (P(VDF-co-CTFE)-g-PSSA) 가지형 공중합체를 합성하였다. 티타늄 아이소프로폭사이드(TTIP)와 가지형 공중합체를 졸-겔 공정을 통하여 $TiO_2$/가지형 공중합체 복합막을 제조하였다. TTIP는 가지형 공중합체의 친수성을 가진 PSSA 영역에만 선택적으로 결합하였으며 그곳에 $TiO_2$ 나노 입자가 형성되어 성장하였다. 이와 같은 결과를 적외선과 자외선 분광학으로 확인할 수 있다. 함수량과 이온 교환 능력 (IEC)는 TTIP의 함량에 따라 감소하였고 이것은 막이 가진 술폰산의 수가 감소하기 때문이었다. TTIP가 5 중량%일 때, 막의 기계적 강도는 증가하고 수소이온 전도도도 유지되었다.
유기금속 화학 증착법(MOCVD)을 이용하여 Si(100) 기판 위에 $TiO_2$와 PbO의 동시 증착으로 $Pb(TMHD)_2$(PT) 박막을 증착하였다. 원료물질로는 Titanium tetra-isopropoxide(TTIP)와 $Pb(TMHD)_2$를 사용하였다. 증착온도를 $520^{\circ}C$, Pbdbfid을 30 sccm으로 고정하고, 전체유량을 750 sccm으로 하여 TTIP의 증발온도와 유량에 따른 PT 박막의 XRD 변화를 관찰하였다. PT 박막 생성은 TTIP의 증발온도 및 유량이 각각 48~$50^{\circ}C$와 18~22sccm 영역에서 생성되었으며, 생성된 박막과 기판의 계면에서는 Pb, Si, O의 상호확산을 관찰할 수 있었다.
Recently, the application field of solar panels is increasing. Accordingly, the demand for flexible devices is also steadily increasing. It is therefore necessary to develop $TiO_2$ paste for low-temperature annealing for flexible DSSC fabrication. In this study, the $TiO_2$ paste for low-temperature annealing with varying molar ratio of titanium isopropoxide (TTIP) was prepared, and DSSC was fabricated and its characteristics were compared. As a result, there was no deformation of the particles on the surface in the SEM data. However, the highest open circuit voltage, short circuit current, and fill factor were measured in the DSSC unit cell prepared by adding 0.5 mol of TTIP to the $TiO_2$ paste, and the highest efficiency was 4.148%.
The pure $TiO_2$ particles have been prepared in vapor-phase hydrolysis of titanium tetraisopropoxide(TTIP). The rate of TTIP hydrolysis was so fast that the overall rate of formation of $TiO_2$ was controlled by the rate of mixing of TTIP and $H_2O$. Thus, the primary $TiO_2$ particles were prepared in nano sizes to form chainlike aggregates due to rapid coagulation. The pure $TiO_2$ particles as prepared were amorphous at the reactor set temperatures below $400^{\circ}C$ and became anatase at the temperatures of $450^{\circ}C$ above while the weak rutile peaks were also observed above $800^{\circ}C$. The actual size of primary particles as prepared were reduced by increasing the reactor set temperature while their crystalline sizes as well as BET sizes increased by post-sintering.
$1{\mu}l$ 정도의 미량 titanium tetraisopropoxide(TTIP)를 주사기를 사용하여 1 cc 부피의 증발관에 주입하여 기화시킨 후 질소에 의해 직경 4 mm, 길이 35 cm의 관형 에어로졸반응기로 운반하여 열분해 시킴으로써 30-300 nm 크기의 $TiO_2$ 나노입자를 제조하였으며, 반응온도 및 TTIP 증기 농도가 생성된 $TiO_2$ 입자의 형상, 크기, 결정성 등에 미치는 영향을 조사하였다. 전구체 증기 농도 1 mol%에서 반응온도를 300, 500, $700^{\circ}C$로 변화시킨 결과 반응온도가 증가함에 따라 응집체를 구성하고 있는 1차 입자 크기가 감소하였고, $700^{\circ}C$에서는 입자 크기분포가 bimodal 형태를 나타내었다. 반응온도를 $700^{\circ}C$로 유지하고 전구체 증기 농도를 1, 3.5, 7 mol%로 변화시킨 결과 전구체 증기 농도 3.5 mol% 이상에서는 1 mol%에서 관찰되었던 bimodal 분포가 사라지고 응집체 내 1차 입자들의 개수가 상대적으로 많이 증가하였다. 반응온도 및 전구체 농도가 입자의 형상, 크기분포에 미치는 이와 같은 영향들을 이전의 연구결과들과 함께 비교 분석하였다.
TiO2 sols were prepared by hydrolysis and polymerization of titanium tetra-isopropoxide (TTIP) in the presence of diethanolamine (DEA). The optimal mole ratio of water to TTIP is 2 and the concentration of the TiO2 sol 0.7 M. Golden TiN films without cracks were obtained by dipping Si(110) wafers into the TiO2 sol and followed by nitridation in NH3 at 1100$^{\circ}C$ for 5 h. The TiN films were studied by an optical microscope, DTA, TGA and X-ray analysis.
고효율 염료감응 태양전지를 제작하기 위해 Sol-gel법을 사용하여 $TiO_2$ 분말을 제조하였다. 제조 과정 중 다양한 양의 nitric acid를 첨가하여 pH를 조절하였다. Sol-gel법을 위한 출발 물질로 titanium (IV) isopropoxide(TTIP)와 DI water를 사용하였으며 nitric acid은 0, 0.05, 0.1, 0.15의 몰비(nitric acid/TTIP)로 첨가하였다. 첨가한 결과 pH는 $22^{\circ}C$에서 각각 5.52, 2.26, 1.68, 1.38이었다. 얻어진 $TiO_2$ 콜로이드 용액은 결정성 있는 분말로 제조 후 $5{\times}5[mm^2]$ 크기의 염료감응 태양전지를 제작하는데 사용 되였다. $TiO_2$의 결정구조 및 형태는 cell의 XRD와 FE-SEM으로 분석되었고 전기화학적 특성을 분석하기 위해 irradiation of AM 1.5 ($100mW/cm^2$) simulatedsunlight에서 I-V 곡선을 측정하였다. 측정 결과 몰비(nitric acid/TTIP) 0.05, pH가 2.26일 때 가장 우수한 효율 특성을 보였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.