• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04a
• /
• pp.18-22
• /
• 2004

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with rubbing alignment method on polyimide surfaces using thin plastic substrates. It was found that monodomain alignment of NLC is obtained with rubbing alignment method on polyimide surfaces using thin plastic substrates. The NLC pretilt angles generated are about $3^{\circ}$ by the rubbing alignment method on thin plastic substrates, However, the pretilt angle are at about $1.7^{\circ}$ lower on the glass substrate than on thin plastic substrate. Also, EO characteristics of the TN-LCD with a rubbed PI surface based on polymer are almost the same as that of the TN-LCD with a rubbed PI surface based on glass. However, the transmittances of the TN-LCD with a rubbed PI surface based on polymer is less than that with a rubbed PI surface based on glass.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.487-488
• /
• 2005

We have investigated the Electro-Optical Characteristics for a nematic liquid crystal (NLC) alignment with rubbing alignment method on polyimide surfaces using plastic substrates. It was found that monodomain alignment of NLC is obtained with rubbing alignment method on polyimide surfaces using thin plastic substrates. EO characteristics of the TN-LCD with a rubbed PI surface based on polymer are almost the same as that of the TN-LCD with a rubbed PI surface based on glass. However, the transmittances of the TN-LCD with a rubbed PI surface based on polymer is less than that with a rubbed PI surface based on glass.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.3
• /
• pp.209-212
• /
• 2012

In this paper, we have studied on the optimal design of the optical compensation film for the TN-LCDs. To have wide viewing angle panels, several methods such as multi-domain method, optical path method, and phase compensation method have been proposed. Among these methods, this paper focused on the phase compensation method. In the phase compensation method, the phase retardation generated from the optical birefringence for the off-axis incident is compensated by using optical films with refractive anisotropy. To compensate the phase retardation of the TN-LCDs, we have proposed design concept for the biaxial optical films and analyzed the optical performance for the proposed structures. The calculation of the dynamic motion of the liquid crystals was based on the Ericksen-Leslie theory and the optical performance of the TN-LCD was calculated from the Extended Jones Matrix Method. From the results, we have confirmed that the optical characteristics of the TN-LCDs with the biaxial films have been improved considerably compared with the TN-LCDs compensated by the combination of the uniaxial films.

• Korean Journal of Optics and Photonics
• /
• v.9 no.6
• /
• pp.417-422
• /
• 1998

In this paper we introduce a method to optimize panel parameters and drive signals in a matrix-adressed bistable twsited-nematic (BTN) liquid crystal display (LCD) panel. We measured the effect of data pulses on optical switching characteristics in a BTN LC cell to model the effect theoretically. We introduce a weighting function to model the effect of data pulses on the switching energy as a function of time. Once the weighting function is known, we can estimate the maximum number of lines for multiplexing operation at a given frame rate by calculating the minimum data pulse width. By characterizing a unit cell as we change panel parameters (for example, d/p ratio), we can optimize parameters for high-speed operation. We found that our theoretical predictions agree very well with experimental results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.2
• /
• pp.207-211
• /
• 2004

We have performed computer simulation to obtain a globa1 optimization of power consumption and viewing angle characteristic of reflective twisted nematic (R-TN) mode liquid crystal display (LCD) with sin81e polarizer and λ/4 plate. Our studies shout that with increasing the twist angle, a steepness of reflectance-voltage curve increase, operation voltages decreases, the region where contrast ratio (CR) greater than 10 increases but the reflectance of the white state starts to decrease at above the twist angle of 75$^{\circ}$. Above the twist angle of 90$^{\circ}$, the R-TN mode LCD shows the most favorable combination of low consumption and good viewing angle characteristic.

• Korean Journal of Optics and Photonics
• /
• v.9 no.2
• /
• pp.117-122
• /
• 1998

We modeled the dynamic switching behavior of a bistable twisted-nematic liquid crystal cell by employing the Berreman's backflow model. Although viscosity paramenters of the liquid crystal material are not known, numerically calculated optical switching characteristics shows good agreement with experimental results. With this model we also have shown that bistable switching can be observed in a $180^{\circ}$ twisted cell only when two alignment layers are rubbed in the opposite direction.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.11
• /
• pp.969-976
• /
• 2007

In this thesis, an anchoring energy in the upper and lower substrates of TFT-LCD cell has been modeled and applied in the numerical calculation of the molecular orientation of the TN-LCD. The molecular orientation of liquid crystals defined as tilt and twist angles was simulated using the Newton-Raphson method and the Gaussian integration method. From the results, the tilt and twist angles for the strong anchoring energy were proven to be coincide with those of the conventional results. on the other hand, for the weak anchoring energy, azimuth angles of the molecules were changed abruptly from $0^{\circ}\;to\;90^{\circ}$ near the middle area of the cell due to the balance of the anchoring energy and the elastic energy of the liquid crystals.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.4
• /
• pp.166-169
• /
• 2007

In applying LCD to TV application, one of the most significant factors to be improved is image sticking on the moving picture. LCD is different from CRT in the sense that it's continuous passive device, which holds images in entire frame period, while impulse type device generate image in very short time. To reduce image sticking problem related to hold type display mode, we made an experiment to drive TN-LCD like CRT. We made articulate images by turn on-off backlight, and we realized the ratio of Back Light on-off time by counting between on time and off time for video signal input during 1 frame (16.7 ms). Conventional CCFL (cold cathode fluorescent lamp) cannot follow fast on-off speed, so we evaluated new fluorescent substances of light source to improve residual light characteristic of CCFL. We realized articulate image generation similar to CRT by CCFL blinking drive and TN-LCD overdriving. As a result, reduced image sticking phenomenon was validated by naked eye and response time measurement.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.21-25
• /
• 2005

In order to implement high pixel density in AMLCDs, high aperture ratio is a very important design factor. We have implemented VGA panels with IPS and TN modes. IPS mode is a very attractive solution to meet the requirement for mobile phone displays. It provides much higher aperture ratio as well as wider viewing angle at extremely high pixel density over 400 ppi.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1121-1124
• /
• 2004

Carbon Nitride exhibits high electrical resistivity and thermal conductivity that are similar to the properties shown by diamond-like carbon (DLC) films. These diamond-like transport properties in Carbon Nitride come in a material consisting of $sp^2$-bonded carbon versus the $sp^3$-carbon of DLC. The diamond-like properties and nondiamond-like bonding make NDLC an attractive candidate for applications. Liquid crystal (LC) alignment capabilities with ion beam exposure on carbon nitride thin films and Electro-Optical (EO) performances of the ion-beam aligned twisted nematic liquid crystal display (TN-LCD) with oblique ion beam exposure on the Carbon Nitride thin film surface were studied. An excellent uniform alignment of the nematic liquid crystal (NLC) alignment with the ion beam exposure on the Carbon Nitride thin films was observed. In addition, the good EO properties of the ion-beam-aligned TN-LCD were achieved. Finally, we achieved the residual DC property of the ion-beam- aligned TN-LCD on the Carbon Nitride thin film.