• Journal of Welding and Joining
• /
• 제33권5호
• /
• pp.35-40
• /
• 2015

Characterization of microstructures and mechanical properties of 83mm thickness EH36-TM welds produced by the combined flux cored arc (FCA) and electro gas (EG) welding processes has been studied with the two different groove conditions, single-V (SV) and double-V (DV) bevels. The welding consumables used for FCA and EG welding processes were ASME/AWS A5.29 (E81T1-K2) and A5.26 (EG72T), respectively. Experimental results showed that all the mechanical properties of welds such as tensile property, CVN toughness and Vickers hardness met IACS requirements. The tensile strength of EG welded plates were reduced by approximately 4% (DV: 3.8%, SV: 4.2%) compared to the base metal. The hardness value of SV-beveled weld metal was slightly lower than that of DV-beveled one. There were no significant differences as per welding groove conditions except for the weld metal. In addition, at the fusion line, the toughness of SV condition was 20J lower and the weld metal was 40J lower than DV condition, respectively. On the basis of microstructural analysis, grain boundary ferrite (GBF) structures for SV condition were 2 times higher volume fraction than for DV condition and their packet sizes were coarsened to almost double. It was thus suggested that the GBF volume fractions and packet sizes in the weld metal of EH36-TM steel plates are the most important factors affecting the mechanical properties of the combined FCA and EG welded joint. Nevertheless, all the results of welds with both DV and SV conditions were found to be excellent.

• 비파괴검사학회지
• /
• 제23권4호
• /
• pp.349-355
• /
• 2003

후방복사 레일리 표면파를 사용하여 부식피로에 의한 재료손상을 평가하였다. $25^{\circ}C$, 3.5 wt.% NaCl 수용액에서 TMCP 강재에 대하여 하중의 크기를 변화시키면서 부식피로 시험을 수행하였다. 각각의 시험편에 대해서 입사각에 따른 후방복사 초음파의 진폭변화를 측정하였다. 후방복사 프로파일이 최대가 되는 입사각으로부터 레일리 표면 탄성파의 속도를 결정하였는데, 부식피로 시험에서 파손수명이 길었던 시험편에서의 표면탄성파의 속도가 더 느렸다. 이 사실은 시험편 표면에 발생한 부식손상이 주로 부식환경에 놓인 시간에 의존함을 의미한다 본 연구에서 얻어진 결과는 후방복사된 레일리 표면 탄성파가 노후 재료의 부식손상을 비파괴적으로 평가하는데 유용한 도구임을 보여주었다.

• Journal of Welding and Joining
• /
• 제34권1호
• /
• pp.7-20
• /
• 2016

A brief overview is given of the development of various structural steels and their welding application technology. Firstly, the general characteristics and welding performance of structural steels used in architecture and bridge are introduced. For safety against earthquakes or strong wind, and for highly efficient welding in high-rise building constructions, ultra high strength steel with tensile strength over 800 MPa or high HAZ toughness steel plates under high heat input welding have been developed. In particular, efficient welding technology ensuring high resistance to cold and hot cracking of ultra high strength steel is reviewed in the present paper. Secondly, various coated steels used mainly for outer part in construction are briefly discussed. Moreover, a major drawback of coated steel during welding operation, and several solutions to overcome such technical problem are proposed. It is hoped that this review paper can lead to significant academic contributions and provide readers interested in the structural steels with useful welding technology.

• Journal of Welding and Joining
• /
• 제8권4호
• /
• pp.69-75
• /
• 1990

In this paper, ultimate compressive strength of TMCP 50HT steel plates (yield stress .sigma.$_{o}$=36kg/mm$^{2}$) with HAZ softening is studied. Finite element method formulated by the author is applied to analyze the elasto-plastic large deflection behaviour of the plates. The influence of HAZ softening breadth, welding direction and slenderness ratio on the ultimate compressive strength is investigated. The results obtained are summarized as 1) With the increasing of the HAZ softening breadth, early plasticity on the plates is formed and then the ultimate compressive strength is decreased, in which about 8% of the ultimate strength for the plate with h/t=4(h: HAZ softening breadth, t: plate thickness) was reduced comparing with no HAZ softening. 2) The large decrease of the ultimate strength for the case that the welding direction is normal to the loading direction is occurred than the case that the welding direction is parallel to the loading direction. 3) The influence of HAZ softening on the ultimate compressive strength is serious for thick plates, while it may be negligible for thin plates.s.

• 한국해양공학회지
• /
• 제1권2호
• /
• pp.67-73
• /
• 1987

The feasibility for a practical use of underwater wet arc welding process is experimentally investigated by using low hydrogen and high oxide type electrodes and TMCP steel plates. Main results are summarized as follows: 1)The absorption speed of the coated low hydrogen and high titanium oxide type eletrodes becomes constant after about 30 minutes in water, and more steeping time in water does not influnce welding arc behavior. 2) By bead appearance and X-ray inspection, the high titanium oxide type electrode is better than the low hydrogen type in underwater arc welding process. 3) The mechanical properties of underwater wet arc welds depend upon welding conditions more than those of in-air welds, and the optimum welding condition can be obtained. 4) Because of quenching effect by rapid cooling rate in underwater wet welding, the maximum hardness of HAZ is increased relatively higher in underwater wet welding, process.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.271-276
• /
• 1998

To apply the wear resistant steel plate for heavy duty vehicle, the wear characterisms of various kinds of commercial steel plates were invesigated by dry sand/rubber wheel tester which was tested under scratch abrasion mode. The wear tested pnaterials were boron steels which were manufactured by thereto machanical control process (TMCP) in order to achieve higher hardness. As the result of the test, wear resistance of steel plate increases with the hardness and carbon content. The wear loss of wear resistance steel plate (Hv440) is a half times than tinat of SWS490A (Hv160) steel plate in dry sand-rubber wheel test and the result in field test is similar to this dry sand/rubber wheel test result. Therefore, dry sand/rubber wheel tester can be used to predict the scratch abrasion life of the parts for heavy duty vehicle.

• 한국강구조학회 논문집
• /
• 제26권4호
• /
• pp.299-309
• /
• 2014

HSA800은 건축구조용 고성능 강재로서 KS규격에 항복강도 650MPa-770MPa, 인장강도 800MPa-950MPa를 가지며 항복비(항복강도/인장강도) 또한 0.85이하로 제한되어있으며 TMCP 기법으로 제조되어 뛰어난 용접성을 나타내는 특징이 있다. 본 연구에서는 국내 최초의 초고층 빌딩인 롯데월드타워의 메가 구조부재를 대상으로 고강도 강재 적용시 구조물 안전성의 변동사항 및 시공성 개선 등을 검토하여 경제적 설계를 위한 대안을 제시하는 것을 목적으로 한다. 대상 부재로는 아웃리거 코어월 매립부 상/하현재, 벨트트러스, 외곽 철골기둥이 선정되었다. 원설계 단면을 등가 도강도 강재 단면으로 환산하여 두께를 결정한 후 중력저항모델, 횡력저항모델, 연쇄붕괴 모델을 구조해 석시뮬레이션을 통하여 성능을 비교 평가하였다. 그 결과 횡강성에 영향을 주지 않는 부재는 고강도 강재 적용이 가능하며 원설계 대비 약 1100톤의 물량 절감 효과가 있었다. 따라서, 고강도 강재를 사용하면 부재 두께를 줄일 수 있으므로 부재 제작성 및 시공성이 향상될 수 있을 것으로 기대된다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.409-412
• /
• 2003

Fatigue strength. especially crack initiation behavior of high strength steel under marine water environment was investigated. Marine structures were usually constructed by lot of weld joints and were designed by basis of the fatigue strength of weld joints. This study was carried out to mini. The fatigue initiation behavior is more important rather than crack propagation behavior under the design of marine structures, because it is very difficult to find out the crack propagation phenomena and repair the damaged part of welded joints in sea water Then, the new configuration specimen for fatigue crack initiation tests was proposed. Using this new specimen, it is easy to carry out the crack initiation tests with relatively low cycling loading and clearly find out a crack initiation fatigue life.

• Journal of Welding and Joining
• /
• 제32권1호
• /
• pp.15-21
• /
• 2014

FCAW(Flux Cored Arc Welding), SAW(Submerged Arc Welding), EGW(Electro Gas Welding), and three-pole SAW are applicable in manufacturing the offshore wind tower. In this paper, mechanical properties of these welded-joints for TMCP steels were evaluated in all above welding processes. The tensile strength of welded-joints for all the welding methods satisfied the standard guideline (KS D 3515). No cracking on weldment was found after the bending test. Changes of weldedments hardness with welding processes were observed. In a weld HAZ (heat-affected zone), a softened HAZ-zone was formed with high heat input welding processes (SAW and EGW). However, the welded-joint fractures were found in the base metal for all cases and small decrease in welded-joint strength was caused by a softened zone. The multi-pole SAW welds exhibited similar mechanical properties comparing to the one with one-pole SAW process.

• 한국전산구조공학회논문집
• /
• 제22권6호
• /
• pp.565-572
• /
• 2009

본 연구에서는 EGW공정 적용에 따른 고강도 극후판 EH36-TMCP강 용접부의 역학적 거동 및 파괴인성 $K_{IC}$ 특성을 고찰하기 위해 먼저 자체 개발한 열분포, 열탄소성 프로그램을 이용한 유한요소해석을 통하여 용접부의 역학적 거동(용접잔류응력, 소성변형율 등의 크기, 분포, 발생기구)을 규명하였다. 그리고 이때 얻어진 잔류응력을 초기응력으로 하여 상용프로그램 ANSYS에서 노치가공으로 인한 응력 재분포 특성 및 잔류응력과 외력의 복합하중에 대한 파괴인성 KIC를 계산하였다. 균열이 존재하는 EGW용접부의 파괴기준$K_{IC}$를 살펴보면, 중첩된 경우가 순수 외부하중(굽힘하중)만 작용하는 경우 보다 파괴 인성치가 다소 감소하는 경향을 보였다. a/W가 작을 경우 중첩의 경우가 순수 외부하중(굽힘하중)만의 경우보다 파괴인성치 차이가 크나, a/W가 증가함에 따라 그 차이가 점차 없어지는 것으로 나타났다.