• 월간산업보건
• /
• s.372
• /
• pp.9-13
• /
• 2019

• 대한예방의학회:학술대회논문집
• /
• 1994.02a
• /
• pp.681-691
• /
• 1994

The American Conference of Governmental Industrial Hygienists (ACGIH) has proposed a threshold limit value (TLV) for benzene of 0.1 ppm. Individuals representing the American Petroleum Institute (API)and the Chemical Manufacturers Association (CMA) have argued that 1) the risk assessment by Rinsky .et al. which ACGIH partially relied upon for its proposed TLV overestimates the risk; however, at the exposures levels of interest - (e.g., 0.1 to 1.0 ppm) for establishing a benzene TLV, the Rinsky et al. assessment provides lower estimates of leukemia risk than most others; 2) ACGIH should not use the Dow study for direct observational evidence of leukemia risk associated with low-level benzene exposure because of confounding exposure; however, it is unlikely that confounding exposures played a role in the excess of leukemia demonstrated in the study, and the Dow cohort was exposed to an average benzene concentration of about 5.5 ppm benzene for 7.11 years (31:1.5 ppm-years), while some of the individuals in the study who died from leukemia were exposed to an average of only 1.0 ppm without the opportunity for highpeak exposures; 3) the Occupational Safety and Health Administration (OSHA) established an 8-hour time-weighted average (TWA) of 1.0 ppm in 1987, and there is no new evidence that would justify reducing the TWA below that level; however, the OSHA TWA of 1.0 ppm was based on economic feasibility and the level of excess risk remaining at 1.0 ppm, i.e., 10 excess leukemia deaths per 1000 workers over an occupational lifetime (45 years) according to OSHA's preferred estimate leaves behind I risk considered significant by OSHA. In addition, chromosomal studies among workers and in animals exposed to benzene indicate that low-level exposure, i.e., 1.0 ppm, is associated with elevated Cytogenetic damage. On the basis of adverse health effects data alone, in this author's opinion, it would be poor science and poor public health policy to establish a benzene TLV greater than 0.1 ppm.

• Wind and Structures
• /
• v.34 no.5
• /
• pp.395-405
• /
• 2022

Tornado-induced damages to high-rise buildings and low-rise buildings are quite different in nature. Tornado losses to high-rise buildings are generally associated with building envelope failures while tornado-induced damages to low-rise buildings are usually associated with structural or large component failures such as complete collapses, or roofs being torn off. While studies of tornado-induced structural damages tend to focus mainly on low-rise residential buildings, transmission towers, or nuclear power plants, the current rapid expansion of city centers and development of large-scale building complexes increases the risk of tornadoes impacting tall buildings. It is, therefore, important to determine how tornado-induced load affects tall buildings compared with those based on synoptic boundary layer winds. The present study applies an experimentally simulated tornado wind field to the Commonwealth Advisory Aeronautical Research Council (CAARC) building and estimates and compares its pressure coefficient effects against the Atmospheric Boundary Layer (ABL) flow field. Simulations are performed at the Wind Engineering, Energy and Environment (WindEEE) Dome which is capable of generating both ABL and tornadic winds. A model of the CAARC building at a scale of 1:200 for both ABL and tornado flows was built and equipped with pressure taps. Mean and peak surface pressures for TLV flow are reported and compared with the ABL induced wind for different time-averaging. By following a compatible definition of the pressure coefficients for TLV and ABL fields, the resulting TLV pressure field presents a similar trend to the ABL case. Also, the results show that, for the high-rise building model, the mean and 3-sec peak pressures are larger for the ABL case compared to the TLV case. These results provide a way forward for the code implementation of tornado-induced pressures on high-rise buildings.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.15 no.3
• /
• pp.221-231
• /
• 2005

In this study, occupational exposures to man-made mineral fibers (MMMFs) including glass wool, rock wool, and continuous glass filament fibers were determined and evaluated on the American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Value (TLV). A total of 171 personal samples collected from 4 glass wool fiber, 2 rock wool fibers, 4 continuous filament glass fiber products manufacturing and a glass fiber and rock wool insulations using industries, and determined respirable fibers concentrations using the National Institute for Occupational Safety and Health (NIOSH) Method 7400, "B counting rule. The fiber concentrations of samples from workers installing thermal insulations in a MMMF using industry showed the highest value: geometric mean (GM) = 0.73 f/cc and maximum = 2.9 f/cc, 70% of them were above the TLV, 1 f/cc. Workers' exposure level (GM= 0.032 f/cc) in the rock wool manufacturing industries was significantly higher than those of glass wool (GM=0.012 f/cc) and continuous filament glass fibers (GM=0.010 f/cc) manufacturing industries (p<0.01). No samples were more than the TLV in the MMMF manufacturing industries. There was a significant difference among companies in airborne fiber levels.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.15 no.3
• /
• pp.176-182
• /
• 2005

American Conference of Governmental Industrial Hygienists (ACGIH) adopted the Lifting Threshold Limit Values ($TLVs^{(R)}$) in 2005 as a guideline for protecting the workers from work-related low back and shoulder disorders associated with repetitive lifting tasks. The TLVs consist of three tables with recommended weight limits for lifting tasks and their determination procedures are simple. The TLVs sans the material weight/the recommended values (LITLVs) were obtained from 45 lifting tasks in ship engine manufacturing factories. These values were compared and correlated with the Recommended Weight Limits (RWLs) and lifting indices (LIs) determined by the Revised Lifting Equation (LE) of the National Institute for Occupational Safety and Health (NIOSH). The average ratio, LITLVs/LIs, was 0.8 (LITLVs: $1.3{\pm}0.8$, LIs: $1.6{\pm}0.7$). Thus, the TLVs underestimated the risk than the LE. The LITLVs were highly correlated with LIs (r=0.82). The predicted value of LITLVs when LIs=1 wa 0.76. Using the predicted TLVs the higher risk ones of a large number of tasks can be screened to be further investigated.

• 월간산업보건
• /
• s.247
• /
• pp.16-19
• /
• 2008

파라티온(Parathion)은 폭넓고 다방면으로 사용되는 유기 인계 해충 진드기의 살충제이다. 파라티온의 첫 번째 생물학적 반응은 콜린에스테라아제 효소의 활성도 저감이다. 파라티온의 다양한 수준의 동물 노출 실험 결과, 경구 투여량 0.5-6 mg/kg 수준에서 악영향이 관찰되었다. 인간의 경우 파라티온 0.1 mg/kg 이하 수준에서는 RBC 콜린에스테라아제 효소의 활성도 감소가 나타나지 않았다. $0.2-0.8\;mg/m^3$의 작업장 노출 수준에서는 RBC 콜린에스테라아제 효소의 감소가 관찰되었다. 본 연구 결과에 근거하여 흡입 노출농도 $0.35\;mg/m^3$에 해당되는 0.05 mg/kg 이하 용량에서는 파라티온과 관련한 건강상의 생물학적 장애 증상이 유발되지 않았다. 따라서 흡입성 에어로졸과 증기상 형태로 $0.05\;mg/m^3$의 TLV-TWA가 파라티온의 작업장 노출기준으로 권고되었다. 이 노출기준은 부교감 신경의 이상과 다른 생물학적 장애 증상을 예방하는 목적에서 설정되었다. 이 수치는 인간을 대상으로 한 연구에서 얻어진 NOAEL로부터 근거를 둔 것이고, 작업자들의 RBC 콜린에스테라아제 효소의 활성도 저하를 방지하는 용량에 해당되는 것으로 예상된다. 이러한 접근은 RBC 콜린에스테라아제 효소의 억제가 단독 사용자에게서는 나타나지 않는다는 것을 확인하는데 이용되는 Biological Exposure Index의 활용과 일치된다. 인간에게 있어 파라티온 피부노출이 죽음까지도 이를 수 있다는 임상적 증세와 연관되어 있기 때문에 피부경고주석이 권고되었다. 쥐들을 대상으로 한 사료 공급 연구들에서 파라티온의 노출을 통한 명확한 종양의 발생 증가가 관찰되지 않아 비발암성 물질(A4)로 설정하였다. 파라티온의 TLV-STEL과 SEN notation을 설정하기에는 아직 충분한 데이터가 확보되어 있지 않고 있으며 파라티온의 작업 노출 모니터링에 대한 자세한 정보를 얻으려면 아세털콜린에스터라제 억제 농약의 BEI 문서들을 참고하는 것이 필요하다.

• Wind and Structures
• /
• v.33 no.6
• /
• pp.437-446
• /
• 2021

As wind turbine rotors increase, the overall loads and dynamic response become an important issue. This problem is augmented by the exposure of wind turbines to severe atmospheric events with unconventional flows such as tornadoes, which need specific designs not included in standards and codes at present. An experimental study was conducted to analyze the loads induced by a tornado-like vortex (TLV) on horizontal-axis wind turbines (HAWT). A large-scale tornado simulation developed in The Wind Engineering, Energy and Environment (WindEEE) Dome at Western University in Canada, the so-called Mode B Tornado, was employed as the TLV flow acting on a rigid wind turbine model under two rotor operational conditions (idling and parked) for five radial distances. It was observed that the overall forces and moments depend on the location and orientation of the wind turbine system with respect to the tornado vortex centre, as TLV are three-dimensional flows with velocity gradients in the radial, vertical, and tangential direction. The mean bending moment at the tower base was the most important in terms of magnitude and variation in relation to the position of the HAWT with respect to the core radius of the tornado, and it was highly dependent on the rotor Tip Speed Ratio (TSR).

• Wind and Structures
• /
• v.34 no.3
• /
• pp.303-312
• /
• 2022

As wind turbine rotors increase, the overall loads and dynamic response become an important issue. This problem is augmented by the exposure of wind turbines to severe atmospheric events with unconventional flows such as tornadoes, which need specific designs not included in standards and codes at present. An experimental study was conducted to analyze the loads induced by a tornado-like vortex (TLV) on horizontal-axis wind turbines (HAWT). A large-scale tornado simulation developed in The Wind Engineering, Energy and Environment (WindEEE) Dome at Western University in Canada, the so-called Mode B Tornado, was employed as the TLV flow acting on a rigid wind turbine model under two rotor operational conditions (idling and parked) for five radial distances. It was observed that the overall forces and moments depend on the location and orientation of the wind turbine system with respect to the tornado vortex centre, as TLV are three-dimensional flows with velocity gradients in the radial, vertical, and tangential direction. The mean bending moment at the tower base was the most important in terms of magnitude and variation in relation to the position of the HAWT with respect to the core radius of the tornado, and it was highly dependent on the rotor Tip Speed Ratio (TSR).

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.15 no.2
• /
• pp.90-103
• /
• 2005

Objective: This study was carried out to assess the status of working environments, to improve the working environments, and to be helpful to prevent occupational disease. Methods: The authors measured the noise level, concentration of dust, heavy metals, organic solvents, and other chemicals at 95 industries (22 working processes) by type of working process in manufacturing industry of parts and accessories for motor vehicles and its engines from January to December 2003. Samples were measured and analyzed by regulations of Korea Ministry of Labor, manuals of National Institute for Occupational Safety and Health (NIOSH) and Occupational Safety and Health Administration (OSHA). Results: Results are as follows. 1. Major processes exceeding mean noise levels provided the American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Value (TLV) were shakeout [97.5 dB(A)]. shot-blast [94.2 dB(A)], pressing [92.9 dB(A)], crushing [91.2 dB(A)], and cleaning [90.6 dB(A)]. 2. Mean concentrations of dusts were not exceeded to the TLV. But concentration on some points of processes as like welding (6.50 mg/m3), foundry (5.24 mg/m3) were exceeded. 3. Mean concentrations of heavy metals were not exceeded to the TLV. 4. Mean concentrations of organic solvents and chemicals were not exceeded to the TLV. 5. Improving rate for working environment were significantly higher in industries with health manager than without (p<0.05), and by increasing the year of working environmental measurement (p<0.01). Conclusions: The results suggest that working processes of exceeding to the TLV will be needed rapid improvement of the working environment, and also the others will be needed positive management of the working environment. Health managers must be recommended to employ in the workplace, and further studies for relationship between working environment and health effects for the workers must be carried out.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.5 no.1
• /
• pp.16-39
• /
• 1995

From July 8 to September 2 1994, asbestos exposure level among asbestos textile workers was surveyed. Six plants out of plants in Korea were selected for this study. In addition to the exposure level, the relationship between the level of exposure and some factors affecting exposure were studied. Also, using historical data of asbestos concentrations in asbestos textile plants plus current data, trend of asbestos exposure level could be introduced. Historical exposure level was estimated on the basis of these data. The main results of this study are follows. 1. Average concentration of all six plants surveyed was 1.54 f/cc, and range of those concentrations was 0.03 - 11.58 f/cc. The minimum average concentration was 0.32 f/cc and the maximum was 8.04 f/cc which is four times higher than the Korean standard. A wide difference of exposure level among the workers of different plants was observed. In three plants, the half of all the plants surveyed, their average concentrations exceeded the Korean standard, and those in all the plants exceeded the ACGIH TLV. 2. Among total 56 samples, 22 samples(39%) were in excess of the Korean standard, and 53 samples(95%) were above the ACGIH TLV. Among 32 personal samples, 15 samples(47%) exceeded the Korean standard, and 30 samples(94%) exceeded the ACGIH TLV. Among 24 area samples excluding a few samples collected in office area, seven samples exceeded the Korean standard, and 23 samples( 96%) exceeded the ACGIH TLV. 3. Distributions of concentrations were observed by processes. In weaving, the highest, average concentration was 4.29 f/cc, and range was 2.61 - 11.58 f/cc. In spinning, average concentration was 2.22 f/cc, and range was 0.41 - 8.93 f/cc. In carding, average concentration was 1.98 f/cc, and range was 0.23 - 10.93 f/cc, In twisting, average concentration was 1.65 f/cc, and range was 0.21 - 9.83 f/cc. In mixing, the lowest, average concentration was 0.48 f/cc, and range was 0.22 - 1.20 f/cc. 4. All the samples from basic processes of asbestos textile plants were above the ACGIH TLV. Nineteen samples(45%) out of all these 42 samples exceeded Korean standard. Fourteen samples(58%) of total 24 personal samples, and five samples(28%) of total 18 area samples exceeded the Korean standard. Considering processes, all the samples in weaving process exceeded the Korean standard and 50 did 54% of those in spinning, 40% in carding, and 27% in twisting. 5. Trend of decreasing asbestos concentrations in asbestos textile plants was observed by time. 6. Asbestos concentrations in asbestos textile plant in 1975 were estimated to be 11.0 - 92.4 f/cc.